AT&T Partner Plus - Manuals

Installation Overview This guide explains how to install the system. It begins with an example system setup, then follows with an illustration of the components you need to install the system and general guidelines to consider before installation. Next, it providesstep-by-step instructions for conne...

An Example System Setup The next page shows a control unit with two 206 modules andtwo 400 modules, giving the system a capacity of 12 outside lines and 12 extensions. Although your system may differ, thisexample will give you an idea of the types of equipment youcan connect to it. In the example, s...

Required Parts You will have up to three types of system component packages; Figure 1 shows the contents of each package in the area marked by a dashed line. Check your packages to be sure you have the parts shown here (if not, call the appropriatesupport telephone number as instructed on the inside...

Installation Guidelines Telephones and Devices You can connect the following telephones and devices to the system: MLS- and MLC-Model System Phones. System phones require at least ■ two-pair wiring and are compatible with AT&T 4-pair SYSTIMAX™ wiring. Call Assistant Intercom Autodialers with Bus...

Combination Extensions You can connect a standard device (such as a standard phone or an answeringmachine) on an extension by itself, or so that it shares an extension with another piece of equipment (either another standard device or a system phone). Anextension with two devices connected to it is ...

Installation Procedures Before installing the system, be sure you read the safetyinstructions on page ii. WARNING: There are no customer-serviceable components inside the system modules or backplane. There arehazardous voltages within that can cause severe or fatal personal injury. DO NOT OPEN THE M...

4 A) B) C) D) To power down the control unit, pull out the maincircuit breaker on the control unit. On a PARTNER Plus 220V system, move theon/off switch to the “off” position (“O”). Press the AC power cord firmly into the power jack on the top right side of the backplane until it locks into place. P...

Connecting Lines and Extensions If extensions are not wired to any modular jacks, call a qualified service technician. 555-1343 1 2 3 4 555-1344 A) B) C) A) B) C) Test for dial tone at the network interface jacks before connecting outside lines to the controlunit. For the test, connect a standard ph...

Connecting Caller ID Display Units To get Caller ID information for an extension, you mustfirst subscribe to the service (on a per-line basis) fromyour local telephone company, then connect the units asdescribed here. You must connect the Caller ID displayunit directly to the line that supports Call...

Assembling System Phones You can either desk mount or wall mount a system phone. If the system phone is manufactured with a separate stand, you can use the stand to either wall mount the phone or raise the angle of the phone when desk mounting. (The stand is required for MLS-34D phones.) Alternative...

2 A) B) C) 3 A) B) C) Unscrew the phone’s four mounting screws and lift the base of the phone off the top. CAUTION: Do not touch electrical circuitry. To do so will expose you to a risk of electrical shock and possibly damage the equipment. Turn the base of the phone upside down so thatthe phone bas...

Connecting Paging, Music-On-Hold, and Call Reporting (SMDR) Devices SMDR Jack Only steps for connection to the processor module are provided here. Refer to Chapter 4 of the PARTNER PlusProgramming and Use guide and the manufacturer’sinstructions for additional information on installing,programming, ...

Connecting Intercom Autodialers Since the autodialer has a fixed stand, you may need to adjust the height of the system phone—by installing a stand—to match the height of the autodialer. Refer toStep 2 of “Desk Mounting” under “Assembling System Phones” for instructions. You can wall mount an Interc...

Equipment Upgrades Adding New Modules 1 A) B) C) 2 A) B) 3 A) B) Power Jack Handle Tab 4 To power down the control unit, pull out the main circuit breaker. On a PARTNER Plus 220V system, move the on/off switch to the “off” position (“O”). To remove the cover, place one hand on the handle on the bott...

5 A) To replace the cover, while holding the cover at an angle, gently move the top rear edge of the cover over the top of the control unit and match up the grooves where the top edge ofthe cover meets the backplane. Gently push the edge into place. B) Lower the bottom of the cover until it is secur...

Specifications Capacities System 206 Module Extension Jack ■ ■ ■ 12 outside lines via line jacks on ■ 2 outside lines ■ Maximum 2 devices per extension two 206 plus two 400 modules ■ 6 extensions jack, total REN on jack not to 24 extensions via extension jackson four 206 modules 400 Module exceed 2....