AT&T 9371 - Manuals

INSTALLATION 3 3 Attach belt clip to the cordless handset (optional) . Table/Desk Installation To attach To remove Standardelectrical outlet Modular telephone jack 1 Connect the telephone line cord. 2 Connect the power cord. The ANSWER ON/OFF light goes on,and CL f lashes in the Message Window. Use ...

Align tabs on wallmount adapter withholes on bottom ofbase. Snap wallmount adapter firmlyinto place. INSTALLATION 5 Wall Installation 1 Position the wall mount adapter on the base. 9371_book_1ATT 8/14/01 10:00 AM Page 5

Redial Press P , then press r to call last number dialed (up to 32 digits). 7 TELEPHONE OPERATION AT THE HANDSET Intercom 1 Press to signal the base — OR — Press to answer a page from the base. Then speak with someone at the base without tying up the phone line. 2 Press O to disconnect. Answer a Cal...

8 TELEPHONE OPERATION AT THE HANDSET Handset Ringer Style/Battery Save You can select from four different handset ringer styles, or turn the ringeroff and extend the battery life. 1 Make sure the handset is off. 2 Press p to enter programming mode. 3 Press > until the screen displays RINGER: and ...

9 TELEPHONE OPERATION AT THE HEADSET Operating Range This cordless telephone operates within the maximum power allowed bythe Federal Communications Commission (FCC). Even so, this handset andbase can communicate over only a certain distance — which can vary withthe locations of the base and handset,...

10 TELEPHONE OPERATION AT THE BASE Indicates handset is in base On steadily: handset or base speakerphone is in use Flashing quickly: an extension is in use Flashing slowly: a call is on hold Speaker Volume While on a call, use to adjust the volume of what you hear. Base Ringer Volume Switch Use to ...

TELEPHONE OPERATION AT THE BASE 11 Handset Locator Press to locate thehandset. The handsetwill beep for up toone minute or untilyou turn it off bypressing again orpressing o on the handset. NOTE: When the handset is in use the Page/Intercom and Handset Locator features are inactive. Page/Intercom 1 ...

12 TELEPHONE MEMORY AT THE HANDSET Store a Number in m 1 Press p to enter programming mode. 2 Press < or > until the screen displays S ET ONE TOUCH . 3 Press s . A f lashing cursor appears on screen. 4 Enter the telephone number you want to store. Use < to backspace and make a correction. 5...

13 This cordless handset can store an additional 50 telephone numbers withnames in the directory, each up to 16 digits long. Entries are storedalphabetically. For consistency with Caller ID entries, you may wish toenter last names first. Note: Press O at any time to exit memory. Store a Number in th...

14 TELEPHONE MEMORY AT THE HANDSET 4 When you finish entering the name, press s . The screen displays ENTER NUMBER . 5 Enter the telephone number. Use < to backspace and make a correction. Press r to store a pause in the dialing sequence. 6 Press s or p to store your entry. You’ll hear a series o...

15 Delete a Number Stored in the Directory 1 Press > (DIR). The screen displays DIRECTORY . 2 Press < or > to scroll alphabetically through numbers stored in the directory —OR— Press the dial pad key for the first letter of the entry you want to delete. 3 When the screen displays the number...

HEADLINE LEFT HEADLINE L-SUB 16 You can store 10 telephone numbers (up to 16 digits each) in the basememory locations (0-9). Store a Number in Base Memory 1 Press p on the base to enter programming mode. The SPEAKER light f lashes. 2 Press M . 3 Press the dial pad key (0-9) for the location where yo...

17 CALLER ID OPERATION About Call History This phone assigns each incoming call a number from 1 to 50. The mostrecent call will have the highest number. When the memory is full, theoldest call information is deleted to make room for new incoming callinformation. For each call that comes in, the scre...

18 Delete Records from Call History Delete a Specific Call 1 Locate the record you want to delete from call history. 2 Press s , then press > until ERASE f lashes. 3 Press s . The screen displays ERASE NO YES ALL and the phone number. The current choice f lashes. 4 Press > until YES f lashes. ...

20 Audible Indicators This system gives you voice prompts for feature operations and voiceconfirmations when you press a button or complete an operation. Set the Clock 1 With answering system on, press U until the system announces,“ Change clock. ” 2 Press S until the system announces the correct da...

ANSWERING SYSTEM OPERATION AT THE BASE Turn Answering System on or off Enter Answering Systemfeature setup andchoose a feature to set Confirm/reviewfeature setting Record outgoingannouncement Delete outgoingannouncement,messages Select afeature setting 21 Record Your Announcement NOTE: If you have a...

23 ANSWERING SYSTEM OPERATION AT THE BASE Listen to, Save & Delete Messages The system automatically saves your messages until you delete them,and can store approximately 15 minutes of messages, memos, andannouncements (up to a maximum of 99 messages). After playing a message, the system announc...

24 Call Screening/Intercept 1 Make sure the answering system is on and call screening is turnedon (see “Change call screening” on page 22). Adjust the messageplayback volume. 2 Adjust the message so you can hear the caller’s message. 3 If you decide to take the call, press P on the handset. 4 If you...

25 ANSWERING SYSTEM OPERATION AT TOUCH TONE PHONE Connect with the Answering System You can access many features of this system remotely from a touch tonephone. 1 Dial your telephone number. 2 When the system answers, press # , then enter your Remote Access Code (preset to 19). The system beeps once...

26 ANSWERING SYSTEM OPERATION AT TOUCH TONE PHONE Remote Access Commands (continued) Function: Command: Record memo Press * 8 ; then mailbox number where you want memo recorded; speak afterbeep; press # 5 to exit. End remote access call Press * 0 . Turn system off Press # 0 ; the system announces, “...

27 Charging the Handset Battery Pack This battery should remain charged up to six days with the ringer turnedon and up to 12 days with the ringer off. A fully charged battery providesan average talk time of about five hours. The battery pack needs charging when:• A new battery is installed in the ha...

28 Replacing the Handset Battery Pack 1 Remove the battery compartment cover on the handset by pressing on the indentation and sliding the cover downward. 2 Lift out the old battery pack and disconnect. 3 Align the two holes in the new battery pack’s plug with the socket pins, and snap the plug into...

29 IN CASE OF DIFFICULTY If you have difficulty operating this phone, try the suggestions below.For Customer Service, visit our website at www.telephones.att.com or call 1 800 222–3111. Please retain your receipt as your proof of purchase . If the phone doesn’t work at all, check these items first: ...

30 If you hear noise or interference when using the phone: • Make sure the base antenna is fully upright. • You may be out of range. Move closer to the base. • Press and release C to change to another of the 30 channels available. If noise is exceptionally loud, move closer to the base beforechangin...

31 If you have difficulty hearing messages: Check the volume setting. If the system does not answer after the correct number of rings: • Make sure that the answering system is on. • If Toll Saver is on, the number of rings changes to two when you havenew messages waiting. • In some cases, the system...

PERF . PERF . fo ld Answering System 9371 Remote Commands T o connect with your answering system: 1 Dial y our telephone number fr om a touc h tone phone. 2 When the system ans w e rs ,p ress # ,then enter y our Remote Access Code (pr eset to 19). 3 W ithin tw o seconds, enter a r e mote command fr ...

PERF . Remote Command Press V o ice Help menu *5 Pla y messa g e s # ,then mailbo x number ( 1 , 2 ,o r 3 ) Repeat messa g e # 4 Skip messa g e # 6 Stop #5 Sav e messa g e s H ang up Delete messa g e #9 while messa g e pla y s Revie w announcement #7 Recor d announcement *7 ,speak after beep, pr ess...