AT&T 9357 - Manuals

Use only the power cord supplied with this product. If you need areplacement, call 1 800 222–3111. 3 Charge the handset battery. Place the handset in the base. Charge the battery for at least 16 hoursthe first time. 4 Check for dial tone. After the batteries are charged, pick up the handset and pres...

5 INSTALLATION Wall Installation 1 Connect the telephone line cord. 2 Connect the power cord. CL f lashes in the Message Window. Use only the power cord supplied with this product. If youneed a replacement, call 1 800 222–3111. 3 Mount the base on the wall. 4 Follow Steps 3–5 in “Table/Desk Installa...

TELEPHONE OPERATION 6 End a Call Press O — OR — Place handset in base. Exit programming. Cancel a page. Handset Volume While on a call, adjust volume of what you hear. Hold Press to put acall on hold.Press again torelease hold — OR — Lift the handsetof an extension. Answer a Call Press any keyexcept...

8 TELEPHONE OPERATION Handset Ringer Style/Battery Save You can select from four different handset ringer styles, or turn the ringeroff and extend the battery life. 1 Make sure the handset is off. 2 Press G to enter programming mode. 3 Press > until the screen displays RINGER: . 4 Press s . The s...

9 TELEPHONE OPERATION Operating Range This cordless telephone operates within the maximum power allowed bythe Federal Communications Commission (FCC). Even so, this handset andbase can communicate over only a certain distance — which can vary withthe locations of the base and handset, the weather, a...

10 TELEPHONE MEMORY This cordless phone can store 20 telephone numbers with names, each upto 16 digits long. Entries are stored alphabetically. For consistency withCaller ID entries, you may wish to enter last names first. Note: Press O at any time to exit memory. Store Memory Numbers 1 Press G . Th...

11 4 When you finish entering the name, press s . The screen displays ENTER NUMBER . 5 Enter the telephone number. Use < to backspace and make a correction. Press r to store a pause in the dialing sequence. 6 Press s to store your entry. The screen displays SAVING… and you’ll hear a series of bee...

12 TELEPHONE MEMORY Delete Numbers Stored in Memory 1 Press > (DIR). The screen displays DIRECTORY . 2 Press < or > to scroll alphabetically through numbers stored in memory —OR— Press the dial pad key for the first letter of the entry you want to delete. 3 When the screen displays the numb...

13 CALLER ID OPERATION About Call History This phone assigns each incoming call a number from 1 to 50. The mostrecent call will have the highest number. When the memory is full, theoldest call information is deleted to make room for new incoming callinformation. For each call that comes in, the scre...

14 CALLER ID OPERATION Delete Records from Call History Delete a Specific Call 1 Locate the record you want to delete from call history. 2 Press s , then press < or > until ERASE f lashes. 3 Press s . The screen displays ERASE NO YES ALL and the phone number. The current choice f lashes. 4 Pre...

15 CALLER ID OPERATION Store a Call History Record in Memory 1 Locate the record in call history you want to store in memory. 2 If you wish to change how the number is stored, press # . The screen displays any alternate dialing sequences available for this call (area code + number; 1 + area code + n...

HEADLINE LEFT HEADLINE L-SUB 16 Audible Indicators This system gives you voice prompts for feature operations and voiceconfirmations when you press a button or complete an operation. Set the Clock 1 With answering system on, press U until the system announces,“ Change clock. ” 2 Press S until the sy...

17 ANSWERING SYSTEM OPERATION AT THE BASE Record Your Announcement NOTE: If you have assigned different mailboxes to different people, be sure to tell callers in your announcement to press * 1 , * 2 , or * 3 while the announcement is playing to leave a message in the appropriatemailbox. Remember to ...

18 ANSWERING SYSTEM OPERATION AT THE BASE Answering System Feature Setup You can set up one feature at a time, or you can set up a feature and thenmove on to set up another feature. 1 Make sure the answering system is on. 2 Press and release U until you hear the system announce the feature you want ...

19 ANSWERING SYSTEM OPERATION AT THE BASE Listen To, Save & Delete Messages The system automatically saves your messages until you delete them,and can store approximately 15 minutes of messages, memos, andannouncements (up to a maximum of 99 messages). After playing a message, the system announc...

20 ANSWERING SYSTEM OPERATION AT THE BASE Call Screening/Intercept 1 Make sure the answering system is on, and set the message playbackvolume control above level 1 so you can hear the caller’s message. 2 If you decide to take the call, press P on the handset. 3 If you pick up an extension phone duri...

21 ANSWERING SYSTEM OPERATION AT TOUCH TONE PHONE Connect with the Answering System You can access many features of this system remotely from a touch tonephone. 1 Dial your telephone number. 2 When the system answers, press # , then enter your Remote Access Code (preset to 19). The system beeps twic...

23 Charging the Handset Battery Pack This battery should remain charged up to six days with the ringer turnedon and up to 12 days with the ringer off. A fully charged battery providesan average talk time of about five hours. The battery pack needs charging when:• A new battery is installed in the ha...

24 Replacing the Handset Battery Pack 1 Remove the battery compartment cover on the handset by pressing on the indentation and sliding the cover downward. 2 Lift out the old battery pack and disconnect. 3 Align the two holes in the new battery pack’s plug with the socket pins, and snap the plug into...

If you have difficulty operating this phone, try the suggestions below.For Customer Service, visit our website at www.telephones.att.com or call 1 800 222–3111. Please retain your receipt as your proof of purchase . If the phone doesn’t work at all, check these items first: • Make sure the AC adapte...

26 IN CASE OF DIFFICULTY If you hear noise or interference when using the phone: • Make sure the base antenna is fully upright. • You may be out of range. Move closer to the base. • Press and release G to change to another of the 30 channels available. If noise is exceptionally loud, move closer to ...

If you have difficulty hearing messages: Check the volume setting. If the system does not answer after the correct number of rings: • Make sure that the answering system is on. • If Toll Saver is on, the number of rings changes to two when you havenew messages waiting. • In some cases, the system ma...

PERF . PERF . fo ld Answering System 9357 Remote Commands T o connect with your answering system: 1 Dial y our telephone number fr om a touc h tone phone. 2 When the system ans w e rs ,p ress # ,then enter y our Remote Access Code (pr eset to 19). 3 W ithin tw o seconds, enter a r e mote command fr ...

PERF . Remote Command Press V o ice Help menu *5 Pla y messa g e s # ,then mailbo x number ( 1 , 2 ,o r 3 ) Repeat messa g e # 4 Skip messa g e # 6 Stop #5 Sav e messa g e s H ang up Delete messa g e #9 while messa g e pla y s Revie w announcement #7 Recor d announcement *7 ,speak after beep, pr ess...