AT&T 1305 - Manuals - manualsarea.com

Page 2 - I N S T A L L A T I O N; Insert the microcassette.; TEL SET; Connect the power adapter.

I N S T A L L A T I O N 1 Insert the microcassette. Slide the cover down and insert the microcassette with the full reel at thebottom. Replace the cover. 1 2 Connect the line cord. Plug the line cord into a modular wall jack. 3 Connect a telephone (optional). Plug the line cord from the telephone in...

Page 3 - O P E R A T I O N; Recording Your Announcement

O P E R A T I O N 2 Repeat all or part of a message / Record a memo or phone conversation Skip all or part of a message / Record outgoing message Microphone Begin message playback / Stop or pause message playback Decrease volume / Erase all or selected messages Recording Your Announcement Before usi...

Page 4 - To review your announcement; Turning the System On or Off

2 Press and hold A for two seconds, then release the button and wait for the system to beep. 3 After the beep, speak toward the microphone, from about nine inchesaway. 4 Press and release p , when you are finished. The tape resets automatically and plays the announcement, and the MESSAGE light goeso...

Page 5 - Priority Call Signal; MESSAGE Light

Priority Call Signal When a caller enters the Priority Calling Code from a touch tone phone, thesystem beeps loudly to alert you that you have a priority call. You’ll need toprovide select callers with the Priority Calling Code (preset to 1235) in orderfor them to use this feature. Your Priority Cal...

Page 7 - Call Screening/Intercept; — OR —

5 If you wish, press and release f to fast forward while the memo is playing — OR — Press and release to rewind — OR — Press and release p to pause. Two-Way Recording You can record a phone conversation (the length of the recording depends onthe length of your microcassette). You can listen to the r...

Page 8 - When the Tape is Full; Saving Messages on One Side of Tape; Saving Messages When Tape is Full; Changing/Removing the Microcassette

When the Tape is Full When the recording side of the tape is completely full, the system beeps, theMESSAGE light f lashes rapidly, and the system turns itself off because it cannotrecord a caller’s message. The system answers calls after 10 rings and beeps,but does not play an outgoing announcement ...

Page 9 - R E M O T E O P E R A T I O N

Remote Access Code You can use many features of this answering system remotely from a touchtone phone. Most features can be accessed only after you enter a RemoteAccess Code. (The preset Remote Access Code is printed on the label on thebottom of the answering system.) Connect with the Answering Syst...

Page 10 - Room Monitor; Connect with the answering system and listen to messages.; Turn System On

Room Monitor You can call the answering system and listen to any activity in the room for15 seconds. 1 Connect with the answering system and listen to messages. 2 Press 3 3 . You can listen after the beep. 3 After 15 seconds, the system exits Room Monitor and beeps twice. Turn System Off 1 Connect w...

Page 11 - I N C A S E O F D I F F I C U L T Y

If this answering system does not work properly, tr y the following suggestions.If you’re still having difficulty, call 1 800 722–9125. If the MESSAGE light flashes rapidly: • The tape is full.• No outgoing announcement is recorded. If you have difficulty hearing messages: The recording heads might ...

Page 12 - If the system does not respond to remote commands:

I N C A S E O F D I F F I C U L T Y If the system does not respond to remote commands: • Make sure you are calling from a touch tone telephone. If you hear clicks when you dial, the phone is not a touch tone phone. • There might be noise or interference on the phone line. Press dial buttons firmly. ...

Page 13 - From a Remote Touch Tone Phone; From a Remote Touch Tone Phone

© 1998 Philips Consumer Communications L.P. All rights reserved. Printed in China. 848230090 Issue 1AT&T From a Remote Touch Tone Phone To connect with your answering system:1 Dial your telephone number from a touch tone phone. 2 When the system answers, press * * during the announcement, then e...