APC SUOL1000UXI - Manuals - manualsarea.com

Page 3 - NPACKING; UPS; Placement; Sm; NSTALLATION; TTACH; The UPS is shipped with the front bezel removed

1 990-1137, 3/02 1: I NSTALLATION U NPACKING Inspect the UPS upon receipt. APC designed robust packaging for your product. However, accidents and damage may occur during shipment. Notify the carrier and dealer if there is damage. The packaging is recyclable; save it for reuse or dispose of it proper...

Page 4 - Batteries must be Sealed Lead-Acid type.

990-1137, 3/02 2 2. C ONNECT THE E XTERNAL B ATTERIES 3. C ONNECT THE EQUIPMENT TO THE UPS AND C ONNECT THE UPS TO THE AC P OWER S UPPLY 1. On the back panel, plug the female end of the power cord into the receptacle. Then plug the male end into a two-pole, three-wire, grounding receptacle. Avoid us...

Page 5 - PLUS; NT

3 990-1137, 3/02 5. P ROGRAMMING S MART -UPS O N - LINE WITH A PPROPRIATE N UMBER OF B ATTERY P ACKS It is important to follow these instructions. The number of batteries affects the run time calculations the Smart-UPS On-Line performs when it is running on battery power. 5A. U SING P OWER C HUTE ® ...

Page 6 - PERATION; RONT; not a normal condition. To cold start the unit, push and hold the; ELF; User Configurable Items

990-1137, 3/02 4 3: O PERATION F RONT P ANEL Power On Power Off For Position Only | Cold Start When the UPS is off and there is no utility power, use the cold start feature to apply power to the connected equipment from the UPS’s battery. Cold start is not a normal condition. To cold start the unit,...

Page 7 - On Battery

5 990-1137, 3/02 U TILITY P OWER During normal operation, the UPS monitors the utility power and delivers power to the connected equipment. If your system is experiencing excessive periods of high or low voltage, have a certified electrician check your facility for electrical problems. If the proble...

Page 8 - HUTDOWN; EAR

990-1137, 3/02 6 Battery Charge The five-LED display on the right of the front panel shows the present charge of the UPS battery as a percentage of the battery capacity. When all five LEDs are lit, the battery is fully charged. The LEDs extinguish, from top to bottom, as the battery capacity diminis...

Page 9 - To connect optional external battery pack(s) to the UPS, refer to the

7 990-1137, 3/02 B ASIC C ONNECTORS Computer Inter- face Port Power management software and interface kits can be used with the UPS. Use only interface kits supplied or approved by APC. Use the APC supplied cable to connect to the Computer Interface Port. DO NOT use a standard serial interface cable...

Page 11 - ERMINAL

9 990-1137, 3/02 N OTE : S ETTING THESE ITEMS REQUIRES SOFTWARE , OPTIONAL HARDWARE , OR CONFIGURATION IN T ERMINAL M ODE . F UNCTION F ACTORY D EFAULT U SER S ELECTABLE C HOICES D ESCRIPTION Output Frequency Automatic 50 ± 3 Hz, 50 ± 0.1 Hz, 60 ± 3 Hz, 60 ± 0.1 Hz Sets the allowable output frequenc...

Page 12 - RANSPORTING YOUR; Follow these steps to prepare the UPS for transport.; TORAGE

990-1137, 3/02 10 4: T RANSPORT , M AINTENANCE , AND T ROUBLESHOOTING T RANSPORTING YOUR UPS Always DISCONNECT THE BATTERY before shipping in compliance with U.S. Department of Transportation (DOT) regulations. This requirement applies whether the UPS is shipped alone or installed in an equipment ra...

Page 13 - Replace Battery

11 990-1137, 3/02 T ROUBLESHOOTING Use the chart below to solve minor UPS installation problems. Refer to the APC web site www.apc.com for assistance with complex UPS problems. P ROBLEM AND P OSSIBLE C AUSE S OLUTION UPS WILL NOT TURN ON ON button not pushed. Press the ON button once to power the UP...

Page 15 - Refer to the information provided at the APC Internet site:

13 990-1137, 3/02 5: C ONTACT , R EGULATORY , AND W ARRANTY I NFORMATION C ONTACTING APC Refer to the information provided at the APC Internet site: http://www.apc.com/support R EGULATORY A GENCY A PPROVALS N 394 B ME 61 D ECLARATION OF C ONFORMITY geprüfte Sicherheit