APC SUA750RM1U - Manuals - manualsarea.com

Page 3 - Introduction; NSTALLATION; Read the Safety Instruction sheet before installing the UPS.; Unpacking; on servers with permanently attached power cords.; Positioning the UPS; Place the UPS where it will be used.; The UPS is heavy. Select a location sturdy enough to handle

1 Introduction American Power Conversion Corporation (APC) is the leading national and international manufac-turer of state-of-the-art uninterruptible power supplies, redundant switches, power management soft-ware, and related equipment. APC products protect hardware, software, and data from power d...

Page 4 - Installing the Rails in the Rack

2 Installing the Rails in the Rack The UPS fits in a standard 46.5-cm (19-inch) rack. Mounting brackets and rails are packaged sepa-rately within the main box. Cleats for rack mounting are preinstalled on the UPS. 8 8 2

Page 5 - Mounting the UPS in a Rack; Install the UPS at or near the bottom of the rack.; Step B

3 Mounting the UPS in a Rack The UPS is heavy. To lighten it, you may remove the battery before mounting the unit in the rack (Steps 1 and 2). Install the UPS at or near the bottom of the rack. Check to make sure the rack will not tip after installing the UPS into the rack. Step B Step A Step 1 Step...

Page 6 - Connecting Equipment and Power to the UPS; Step 1

4 Installing and Connecting the Battery and Attaching the Front Bezel Connecting Equipment and Power to the UPS S MART -UPS R EAR P ANEL 230V Models 120/100V Models Step 1 Step 2 Step 3 Step 4

Page 7 - Do not connect a laser printer to the UPS. A laser; Do not; Serial Port; Use only interface kits supplied or approved by APC.

5 1. Connect equipment to the UPS. Note: Do not connect a laser printer to the UPS. A laser printer draws significantly more power than other types of equipment and may overload the UPS . 2. Add any optional accessories to the Smart-Slot. 3. Using a power cord, plug the UPS into a two-pole, three-wi...

Page 8 - PERATION; Power On

6 2: O PERATION S MART -UPS F RONT P ANEL 230/100V Models 120V Models Power On Power Off Online The online LED illuminates when the UPS is supplying utility power to the connected equipment. If the LED is not lit, the UPS is either not turned ON, or is supplying battery power.

Page 9 - On Battery Operation

7 AVR Trim This LED illuminates to indicate the UPS is compensating for a high utility voltage. AVR Boost This LED illuminates to indicate the UPS is compensating for a low utility voltage. On Battery When the on battery power LED is lit the UPS is supplying battery power to the connected equipment....

Page 12 - Storage; Refer to; Disconnecting the Battery for Transport; The battery may remain in the UPS it does not have to be removed.; Shut down and disconnect any equipment attached to the UPS.

10 4: S TORAGE , M AINTENANCE , AND T RANSPORTING Storage Store the UPS covered and positioned as for proper functioning, in a cool, dry location, with the bat-teries fully charged. At -15 to +30 ° C (+5 to +86 ° F), charge the UPS battery every six months. At +30 to +45 ° C (+86 to +113 ° F), charg...

Page 13 - ROUBLESHOOTING; replace battery

11 5: T ROUBLESHOOTING Use the chart below to solve minor Smart-UPS installation and operation problems. Refer to the APC web site, www.apc.com, for assistance with complex UPS problems. P ROBLEM AND P OSSIBLE C AUSE S OLUTION UPS WILL NOT TURN ON Battery not connected prop-erly. Check that the batt...

Page 14 - Specifications

12 P ROBLEM AND P OSSIBLE C AUSE S OLUTION T HE OVERLOAD LED IS LIT AND THE UPS EMITS A SUSTAINED ALARM TONE The UPS is overloaded. The connected equipment exceeds the specified “maximum load” as de-fined in Specifications at the APC web site, www.apc.com . The alarm remains on until the overload is...

Page 15 - UPS; Utility Voltage; Press and hold the

13 P ROBLEM AND P OSSIBLE C AUSE S OLUTION UPS OPERATES ON BATTERY ALTHOUGH NORMAL LINE VOLTAGE EXISTS UPS input circuit breaker tripped. Reduce the load on the UPS by unplugging equipment and resetting the circuit breaker (on the back of UPS) by pressing the plunger in. Very high, low, or distorted...

Page 16 - Service; Review the problems discussed in the; Contacting APC; Refer to the information provided at the APC Internet site,

14 Service If the UPS requires service do not return it to the dealer. Instead, follow these steps: 1. Review the problems discussed in the Troubleshooting section of this manual to eliminate com- mon problems. 2. If the problem persists, contact APC Customer Service through the APC web site, www.ap...

Page 17 - Regulatory Agency Approvals and Radio Frequency Warnings

15 6: R EGULATORY AND W ARRANTY I NFORMATION Regulatory Agency Approvals and Radio Frequency Warnings 230V MODELS This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take corrective ac-tions. 120V MODELS This equip...