APC Automatic Transfer - Manuals

Automatic Transfer Switch - Installation and Quick Start 3 Overview Front panel Configuration A B Output Input Preference A B Au tomatic Tran sfer Switch Reset Link - RX/TX Status 10/100 Smar t Sl ot Network Managem ent Card m ph00 26 a No. Item Description/Function  Reset switch Restarts the Netwo...

4 Automatic Transfer Switch - Installation and Quick Start Installation Attach mounting brackets Attach the left and right mounting brackets to the unit, using two flat-head, Phillips screws (provided) for each bracket. Disassemble the adjustable brackets The adjustable brackets are necessary only i...

Installation Automatic Transfer Switch - Installation and Quick Start 5 Attach rear segments to the rack 1. Insert caged nuts (provided with your enclosure) on the enclosure’s rear vertical mounting rails at your chosen location. 2. Align the rear segments of the adjustable bracket with the caged nu...

Installation 6 Automatic Transfer Switch - Installation and Quick Start Mount the Automatic Transfer Switch in the enclosure 1. Position the Automatic Transfer Switch in front of the mounted rear adjustable bracket segments. 2. Align the front and rear adjustable bracket segments, and slide the fron...

Automatic Transfer Switch - Installation and Quick Start 7 Quick Configuration Overview You must configure the following TCP/IP settings before the Automatic Transfer Switch can operate on a network: • IP address of the Automatic Transfer Switch • Subnet mask • Default gateway TCP/IP configuration m...

Quick Configuration 8 Automatic Transfer Switch - Installation and Quick Start Device IP Configuration Wizard You can use the Device IP Configuration Wizard on a Windows NT ® 4.0, Windows 2000 ® , Windows 2003, or Windows XP computer to discover unconfigured Automatic Transfer Switches and configure...

Quick Configuration Automatic Transfer Switch - Installation and Quick Start 9 BOOTP. You can use an RFC951-compliant BOOTP server to configure the TCP/IP settings for the Automatic Transfer Switch. 1. Enter the Automatic Transfer Switch’s MAC and IP addresses, the subnet mask and default gateway se...

Quick Configuration 10 Automatic Transfer Switch - Installation and Quick Start 2. A properly configured DHCP server responds with a DHCP offer that includes all of the settings that the Automatic Transfer Switch needs for network communication. The DHCP offer also includes the Vendor Specific Infor...

Automatic Transfer Switch - Installation and Quick Start 11 How to Access the Automatic Transfer Switch Interfaces Overview After the Automatic Transfer Switch is running on your network, you can use the interfaces summarized here to access the unit. Web interface As your browser, you can use Micros...

How to Access the Automatic Transfer Switch Interfaces 12 Automatic Transfer Switch - Installation and Quick Start Telnet/SSH You can access the control console through Telnet or Secure SHell (SSH), depending on which is enabled. (An Administrator can enable these access methods through the Telnet/S...

14 Automatic Transfer Switch - Installation and Quick Start Configuring the ATS Configuring sensitivity The sensitivity setting controls how tolerant the ATS is of fluctuations in power before it switches to the secondary power source. Configure the sensitivity range for your ATS using the Switch Co...

Configuring the ATS Automatic Transfer Switch - Installation and Quick Start 15 Remote access to the control console From any computer on the same subnet as the Automatic Transfer Switch, you can use ARP and Ping to assign an IP address to a Automatic Transfer Switch, and then use Telnet to access t...

16 Automatic Transfer Switch - Installation and Quick Start Recovering From A Lost Password 1. Select a serial port at the local computer and disable any service that uses that port. 2. Connect APC serial cable 990-1000A to the Automatic Transfer Switch serial port and to the serial port on the loca...

Automatic Transfer Switch - Installation and Quick Start 17 Warranty Limited warranty APC warrants the Automatic Transfer Switch to be free from defects in materials and workmanship for a period of two years from the date of purchase. Its obligation under this warranty is limited to repairing or rep...

Warranty 18 Automatic Transfer Switch - Installation and Quick Start 4. Pack the unit carefully. The warranty does not cover damage sustained in transit. Enclose a letter with your name, address, RMA number and daytime phone number; a copy of the sales receipt; and a check as payment, if applicable....

Automatic Transfer Switch - Installation and Quick Start 19 Life-Support Policy General policy American Power Conversion ( APC ) does not recommend the use of any of its products in the following situations: • In life-support applications where failure or malfunction of the APC product can be reason...

20 Automatic Transfer Switch - Installation and Quick Start Radio Frequency Interference USA — FCC This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against...

10/2005 990-1233E-001 *990-1233E-001* Customer support for this or any other APC product is available at no charge in any of the following ways: • Visit the APC Web site to access documents in the APC Knowledge Base and to submit customer support requests.– www.apc.com (Corporate Headquarters) Conne...