APC AP9615 - Manuals

2 Product Description Front panel This figure shows the front panel of the 5 Port 10Base-T Hub. The features of the front panel are described in the paragraphs that follow. Figure 1: Front Panel and Connector Detail APC Communications Compatibility Number The APC Communications Compatibility Number ...

3 Product Description continued LEDs The LEDs provide important information concerning opera- tion of the hub and each of its ports. Refer to the table below for a description of the conditions indicated by LEDs . Continued on next page Label Color Activity Description Pwr Green On The hub is receiv...

4 Product Description continued Station ports The Station ports are the first 4 RJ-45 ports, which are labeled 1X – 4X . The Station ports use straight-through UTP cables to connect the hub with: • Workstations or other non-hub devices that you want to include in your network. • The Uplink port of a...

5 Installing the Hub Warning Do not operate the 5 Port 10Base-T Hub where conditions are outside the limits listed in “Product Specifications” on page 14. Installing on critical systems The installation procedure that follows may involve shut-ting off power from the UPS . However, if your setup requ...

6 Installing the Hub continued Installation procedure, continued Matrix- UPS ™ a Shut down and power off the connected equipment. b Turn off the circuit breaker on the bottom left side on the back panel of the UPS . Symmetra ™ Power Array ™ a Shut down and power off the connected equipment. b Turn o...

7 Installing the Hub continued Installation procedure, continued 3 Use a #2 Phillips head screwdriver to remove the 2 screws fastening the SmartSlot cover plate to the back panel of the UPS or triple chassis. Keep the screws for Step 5 below. Save the SmartSlot cover plate for future use (e.g. shipp...

8 Installing the Hub continued Installation procedure, continued 5 Secure the hub with the screws removed in Step 3. 6 Using straight-through UTP cables, connect the Sta- tion ports ( 1X – 4X , in any order) to each worksta- tion’s 10Base-T port or to the Uplink port of a hub to be connected in casc...

9 Installing the Hub continued Installation procedure, continued Symmetra Power Array a Turn on the System Enable switch on the bottom left side on the back panel of the UPS . b Turn on the UPS via the PowerView display. c Power on the connected equipment. Smart-UPS DP a Turn on the ON/OFF switch on...

10 Installing the Hub continued Maximum configuration Using a star configuration, you can cascade up to ten 5 Port 10Base-T hubs together to provide network connections for as many as 32 stations, as shown below in Figure 4. Note the use of a crossover cable to connect the Uplink ports of the 2 cent...

11 Removing the Hub Removal procedure To remove the 5 Port 10Base-T Hub, perform the following steps in the order given. 1 Disconnect all cables from the hub. 2 Turn off the UPS or device that houses the hub. (For detailed instructions, see “Installation procedure” on page 5.) 3 Use a #2 Phillips he...

12 Troubleshooting Troubleshooting suggestions Table 2 provides suggestions for troubleshooting your hub. Continued on next page LED Action Cause Solution Col Blinking Normal data collisions on the network. No action is necessary. Col Blinking excessively Data collisions are occurring because of a h...

13 Troubleshooting continued Troubleshooting suggestions, continued LED Action Cause Solution Partition On 32 consecutive collisions have caused the port to partition. Check that the correct cable is in use and verify that the connected equipment is set to operate at 10 Mbit and half-duplex mode. As...

14 Specifications Product specifications The following table shows the product specifications for the 5 Port 10Base-T Hub. Item Specification Power Input voltage range: 18 – 30 VDC Maximum current draw: 45 mA Physical Size (H × W × D): 1.46 × 4.75 × 4.30 in(3.7 × 12.1 × 10.9 cm) Weight: 0.25 lb (0.1...

15 Warranty Information Limited warranty American Power Conversion ( APC ) warrants the 5 Port 10Base-T Hub to be free from defects in materials and work-manship for a period of 2 years from the date of purchase. Its obligation under this warranty is limited to repairing or replacing, at its own sol...

16 Warranty Information continued Obtaining service To obtain service for your 5 Port 10Base-T Hub, follow this procedure: 1 Note the serial number and date of purchase of the hub. (The serial number is located on the top, interior surface of the hub’s front panel.) 2 Contact APC Customer Support at...

Declaration of Conformity Application of Council Directives 89/336/EEC Standards to Which Conformity is Declared EN55022: 1995, Class BEN50082-1: 1992, including: IEC 1000-4-2: 1995 IEC 1000-4-3: 1995 IEC 1000-4-4: 1995 FCC Part 15, Class B VCCI, Class 2 Manufacturer’s Name and Address American Powe...

w w w . a p c c . c o m Toll-free Customer Support: U. S. & Canada 1-800-800-4272 Austria 0660 6480 Belgium 0800 15063 Czech Republic 0 800 102063 Denmark 800 18 153 Finland 9800 13 374 France 0 800 906 483 Germany 01300818907 Holland 0800 0224655 Hungary 00800 12221 Ireland 1 800 702000 x 2045 ...