APC AP7922 - Manuals

Switched Rack PDU Installation and Quick Start 3 How to Install the Rack PDU Installation guidelines • For a Rack PDU installed in an enclosed communications rack, the recommended maximum ambient temperature is 45° C ( 11 3º F). • Install the Rack PDU so that it does not reduce the air flow required...

How to Install the Rack PDU 4 Switched Rack PDU Installation and Quick Start Attach cords to the tray Attach a cord to the tray by looping the cord and securing it to the tray, using a wire tie (provided). Cords from both banks of outlets may be secured to the bottom tray, or you may attach an addit...

How to Install the Rack PDU Switched Rack PDU Installation and Quick Start 5 For a recessed placement : use four flat-head screws (provided) through the last four holes of each bracket. 2. Insert caged nuts (provided with the rack) on the vertical mounting rails above a number at the start of two U-...

6 Switched Rack PDU Installation and Quick Start Operation Display interface Link - Rx/Tx 10 /100 Status Serial Port Reset - Warning - OK - Overload B2 B1 TOTAL Amp s Am ps Amps Switched Rack PDU Line Indicator LED: Indicates normal (green), warning (yellow), and alarm (red) conditions for bank 1 (B...

Switched Rack PDU Installation and Quick Start 7 Quick Configuration Overview You must configure the following TCP/IP settings before the Rack PDU can operate on a network: • IP address of the Rack PDU• Subnet mask• Default gateway TCP/IP configuration methods Use one of the following methods to def...

Quick Configuration 8 Switched Rack PDU Installation and Quick Start APC Management Card Wizard You can use the APC Management Card Wizard at a Windows ® 98, Windows NT ® 4.0, Windows 2000, or Windows XP computer to configure a Rack PDU. 1. Insert the APC Switched Rack PDU Utility CD into a computer...

Quick Configuration Switched Rack PDU Installation and Quick Start 9 BOOTP. You can use an RFC95 1 -compliant BOOTP server to configure the TCP/IP settings for the Rack PDU. If the BOOTP server is properly configured, the Rack PDU’s default setting ( DHCP & BOOTP ) for BOOT Mode causes it to dis...

Quick Configuration 10 Switched Rack PDU Installation and Quick Start DHCP. You can use a RFC2 1 3 1 /RFC2 1 32-compliant DHCP server to configure the TCP/IP settings for the Rack PDU. 1 . The Rack PDU sends a DHCP request that uses the following to identify itself:– Vendor Class Identifier (APC by ...

Quick Configuration Switched Rack PDU Installation and Quick Start 11 Local access to the control console You can use a local computer to connect to the Rack PDU to access the control console. 1 . Select a serial port at the local computer, and disable any service which uses that port. 2. Use the co...

Quick Configuration 12 Switched Rack PDU Installation and Quick Start 3. Use Telnet to access the Rack PDU at its newly assigned IP address. For example: telnet 156.205.14.141 4. Use apc for both user name and password. 5. See “Control console” on this page to finish the configuration. Control conso...

Switched Rack PDU Installation and Quick Start 13 How to Access a Configured Rack PDU Overview After the Rack PDU is running on your network, you can use the interfaces summarized here to access the unit. Web interface As your browser, you can use Microsoft ® Internet Explorer 5.0 (and higher) or Ne...

How to Access a Configured Rack PDU 14 Switched Rack PDU Installation and Quick Start Telnet/SSH You can access the control console through Telnet or Secure SHell (SSH), depending on which is enabled. An Administrator can enable these access methods through the Telnet/SSH option of the Network menu....

16 Switched Rack PDU Installation and Quick Start How to Recover From a Lost Password You can use a local computer, a computer that connects to the Rack PDU or other device through the serial port to access the control console. 1 . Select a serial port at the local computer, and disable any service ...

Switched Rack PDU Installation and Quick Start 17 How to Download Firmware Updates You can use a local computer that connects to the Rack PDU through the serial port on the front of the unit. 1 . Select a serial port at the local computer, and disable any service that uses that port. 2. Use the conf...

18 Switched Rack PDU Installation and Quick Start Specifications AP7922 Electrical Nominal input voltage 230 V Acceptable input voltage ± 1 0% Nominal input voltage Maximum total current draw 32 A Input frequency 47 – 63 Hz Cord length 1 2 ft ( 1 44 in) Input connectors IEC 309, 32 A, 230 V, 1 ~ plu...

Switched Rack PDU Installation and Quick Start 19 Warranty and Service Limited warranty APC warrants the Rack PDU to be free from defects in materials and workmanship for a period of two years from the date of purchase. Its obligation under this warranty is limited to repairing or replacing, at its ...

20 Switched Rack PDU Installation and Quick Start Life-Support Policy General policy American Power Conversion (APC) does not recommend the use of any of its products in the following situations: • In life-support applications where failure or malfunction of the APC product can be reasonably expecte...

Radio Frequency Interference USA — FCC This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 1 5 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a c...

*990-1694-001* APC Worldwide Customer Support Customer support for this or any other APC product is available at no charge in any of the following ways: • Visit the APC Web site to find answers to frequently asked questions (FAQs), to access documents in the APC Knowledge Base, and to submit custome...