APC AP7562J - Manuals

Basic and Metered Rack Power Distribution Unit 3 How to Install the Basic and Metered PDU Attach the cord retention trays Attach the cord retention trays to the PDU , using four flat-head screws (provided) per tray. Attach cords to the tray Attach a cord to the tray by looping the cord and securing ...

How to Install the Basic and Metered PDU 4 Basic and Metered Rack Power Distribution Unit Toolless mounting 1. Slide the mounting pegs into the holes located in the channel in the rear panel of the enclosure. 2. Snap the PDU into place by pushing it downward until it locks into position. Note You ca...

How to Install the Basic and Metered PDU Basic and Metered Rack Power Distribution Unit 5 Bracket-mounting You can order a rack-mount bracket kit from APC ( AR8116BLK) . The brackets attach to the PDU in either of two directions, shown in the figures in step 1. Consider the orientation of the PDU in...

How to Install the Basic and Metered PDU 6 Basic and Metered Rack Power Distribution Unit 2. Insert mounting screws (provided with the bracket kit) in the top and bottom positions in the channel where the brackets align with the holes. Tighten the screws to secure the PDU to the enclosure. – Recesse...

Basic and Metered Rack Power Distribution Unit 7 Operation Display interface (AP7862J only) Link - Rx/Tx 10 /100 Status Serial Port Reset Press to select line. Press and hold to inver t display. - Warning - OK - Overload L3 L2 L1 Am ps Am ps Phase Indicator LED s: • Indicates the phase corresponding...

8 Basic and Metered Rack Power Distribution Unit Quick Configuration for a Metered PDU Overview You must configure the following TCP/IP settings before the PDU can operate on a network: • IP address of the PDU • Subnet mask• Default gateway TCP/IP configuration methods Use one of the following to de...

Quick Configuration for a Metered PDU Basic and Metered Rack Power Distribution Unit 9 BOOTP & DHCP configuration The Boot Mode setting, a TCP/IP option in the PDU ’s Network menu, identifies how TCP/IP settings will be defined. The possible settings are Manual , DHCP only , BOOTP only , and DHC...

Quick Configuration for a Metered PDU 10 Basic and Metered Rack Power Distribution Unit DHCP. You can use a RFC2131/RFC2132 -compliant DHCP server to configure the TCP/IP settings for the PDU . 1. The PDU sends a DHCP request that uses the following to identify itself:– Vendor Class Identifier ( APC...

Quick Configuration for a Metered PDU Basic and Metered Rack Power Distribution Unit 11 Local access to the control console You can use a local computer to connect to the PDU to access the control console. 1. Select a serial port at the local computer, and disable any service which uses that port. 2...

Quick Configuration for a Metered PDU 12 Basic and Metered Rack Power Distribution Unit 3. Use Telnet to access the PDU at its newly assigned IP address. For example: telnet 156.205.14.141 4. Use apc for both User Name and Password. 5. See “Control console” on this page to finish the configuration. ...

Basic and Metered Rack Power Distribution Unit 13 How to Access a Configured PDU Overview After the PDU is running on your network, you can use several different interfaces to access the PDU . Browser interface As your browser, use Microsoft ® Internet Explorer 5.5 (or higher) to configure PDU optio...

14 Basic and Metered Rack Power Distribution Unit How to Recover From a Lost Password You can use a local computer that connects to the PDU through the serial port on the front panel of the unit. 1. Select a serial port at a local computer, and disable any service that uses the port. 2. Use the conf...

Basic and Metered Rack Power Distribution Unit 15 Specifications AP7862J/AP7562J Electrical Nominal input voltage 173 V, 3-phase Acceptable input voltage ± 10 % Nominal input voltage Input frequency 47 – 63 Hz Input connectors NEMA L21-20 plug Output connectors 42 NEMA 5-15 outlets Maximum total cur...

16 Basic and Metered Rack Power Distribution Unit Warranty and Service Limited warranty APC warrants the PDU to be free from defects in materials and workmanship for a period of two years from the date of purchase. Its obligation under this warranty is limited to repairing or replacing, at its own s...

Basic and Metered Rack Power Distribution Unit 17 Life-Support Policy General policy American Power Conversion ( APC ) does not recommend the use of any of its products in the following situations: • In life-support applications where failure or malfunction of the APC product can be reasonably expec...

Radio Frequency Interference This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial e...

APC Worldwide Customer Support Customer support for this or any other APC product is available at no charge in any of the following ways: • Visit the APC Web site to find answers to frequently asked questions ( FAQ s), to access documents in the APC Knowledge Base, and to submit customer support req...