Andis P333T-PWR - Manuals

Before you Start 8 Quick Start for Hardware Installation: P333T-PWR Stackable Switch Building a stack Follow the guidelines in this section in order to build a working stack using any combination of the following devices: ● P330 series ● P330-ML series ● G700 ● P330 series 1. Add only a single box a...

Before you Start 10 Quick Start for Hardware Installation: P333T-PWR Stackable Switch Stack Master election rules Table 5 lists the switches in order of election priority from highest to lowest. Note: Note: If there are two switches with the same firmware version and the same election priority, the ...

Issue 1 September 2005 13 Chapter 2: Unpack the Device ELECTROSTATIC ALERT: ! ELECTROSTATIC ALERT: Wear an anti-static wrist ground strap whenever you handle components of a P333T-PWR Connect the strap to an approved ground, such as an unpainted metal surface. Equipment Open the box that contains th...

Unpack the Device 14 Quick Start for Hardware Installation: P333T-PWR Stackable Switch Documentation ● Avaya P333T-PWR Quick Start Guide (this document) ● Avaya P333T-PWR Release Notes One RJ45 to DB9F Adapter One DB25M Adapter Four (4) 5/16" Round Head Screws Four (4) Washers Four (4) stand-off...

Documentation Issue 1 September 2005 15 ● Avaya P330 Documentation and Utilities CD (see detail below) ● Avaya Communication Warranty and License Agreement Avaya P330 Documentation and Utilities CD The CD contains the latest User's Guides for the Avaya P330 stackable switches and files for use with ...

Issue 1 September 2005 17 Chapter 3: Mount the Device You can mount the P333T-PWR in a rack. The P333T-PWR chassis fits in most standard 19-inch racks. It is 2U (3.5”, 88 mm) high. Before you Install the P333T-PWR in a Rack ● Disconnect all cables from the unit before proceeding with the rack instal...

Issue 1 September 2005 19 Chapter 4: Power Up Connecting the P333T-PWR to the main electrical supply provides power to the switch. VOLTAGE ALERT: ! VOLTAGE ALERT: To isolate the switch completely, you must disconnect all power connections: AC plug or DC terminal block and DC BUPS power. AC input 1. ...

Issue 1 September 2005 21 Chapter 5: Prepare for Configuration This chapter provides information on preparing the P333R for configuration, and discusses the following topics: ● Establishing a Console Connection ● Assigning a Stack IP Address ● Establishing a Telnet Connection ● Configuring the Switc...

Prepare for Configuration 22 Quick Start for Hardware Installation: P333T-PWR Stackable Switch ● 9600 baud ● 8 bits ● 1 stop bit ● no parity. - If you reset or powered up the switch after connecting and configuring the terminal, Welcome to P333T-PWR appears followed by the Login Name prompt. - If th...

Establishing a Telnet Connection Issue 1 September 2005 23 - At the prompt, type set ip route <dest> <gateway> and replace <dest> and <gateway> with the destination and gateway IP addresses. Establishing a Telnet Connection Perform the following steps to establish a Telnet co...

Prepare for Configuration 24 Quick Start for Hardware Installation: P333T-PWR Stackable Switch For instructions on the CLI, see the Avaya P330 Reference Guide . For instructions on the use of the graphical user interfaces, refer to the P330 Device Manager User Guide on the Avaya P330 Documentation a...

Issue 1 September 2005 27 Chapter 6: Device Manager This chapter describes the installation procedures for the Device Manager. Overview The Device Manager provides the following: ● Managing and monitoring Power over Ethernet. ● Device Configuration - Viewing and modifying the different device config...

Device Manager 28 Quick Start for Hardware Installation: P333T-PWR Stackable Switch ● Sun Microsystems Java plug-in (supplied on the “Documentation and Utilities” CD). Refer to the Release Notes for the exact version of the Java plug-in. Configuring the Device Manager You can configure several Devic...

Device Manager 30 Quick Start for Hardware Installation: P333T-PWR Stackable Switch Figure 8: Device Manager 3. If you do not have the Java plug-in installed, follow the instructions on the Welcome page for a variety of options to install the plug-in (see Installing the Java Plug-in ). Installing th...

Installing the On-Line Help and Java Plug-In on your Web Site Issue 1 September 2005 31 4. Browse to the embweb-aux-files\ folder on the CD. 5. Double-click plugin_a_b_c.exe (a, b and c are the version numbers of the plug-in). 6. Follow the on-screen instructions. Install from the Avaya Web Site Cli...