Airlink101 AWLH6075 - Manuals

Airlink101 AWLH6075 – Manual in PDF format online.

Manuals:

Manual

Manual Airlink101 AWLH6075

Summary

Page 2 - Table of Contents

1 Table of Contents 1. Introduction ..............................................................................................................................2 1.1 Package Contents................................................................................................................2 1....

Page 3 - Package Contents

2 1. Introduction Congratulations on your purchase of the Wireless N PCI Adapter. Its high bandwidth combined with extended wireless coverage delivers fast and reliable connection for all of your networking applications especially when used with other Airlink101® Wireless N, Wireless 300N products. ...

Page 4 - Install the Wireless PCI Adapter; the following picture.; Step 5; Click; Cancel; when you see the; Found New Hardware Wizard

3 2. Install the Wireless PCI Adapter Step 1 SWITCH THE COMPUTER OFF, remove the cover and insert the wireless PCI adapter into an available PCI slot of your computer. Step 2 Fasten the 2 antennas to the antenna connectors on the wireless PCI adapter. Step 3 To improve radio reception, please adjust...

Page 5 - select; Install Utility and Driver; to continue with the installation of the driver software.; Step 7; Next

4 Step 6 Insert the Installation CD in the CD drive. When the autorun screen pops up, select Install Utility and Driver . Windows Vista Users : When you get warning message(s), make sure that you click Allow to continue with the installation of the driver software. Step 7 Click Next .

Page 6 - to start installing the software.; Continue Anyway; at the Windows Logo Screen.

5 Step 8 Click Next to start installing the software. For Windows XP, click Continue Anyway at the Windows Logo Screen.

Page 7 - Finish; and restart your computer as prompted.

6 Step 9 Click Finish and restart your computer as prompted. Step 10 You will see the Airlink101 Wireless Monitor pops up.

Page 8 - installed on your computer.

7 Congratulations! The Wireless N PCI Adapter has now been successfully installed on your computer.

Page 9 - Connect to Wireless Network; Step 1; Click on; Step 2; Type in the network key of your wireless network and click

8 3. Connect to Wireless Network This section describes how to connect your wireless adapter to a wireless network. Note: If the Airlink101 Wireless Monitor does not open on your desktop, you can open the Airlink101 Wireless Monitor utility by double clicking on the Airlink101 Wireless Monitor Utili...

Page 10 - Step 3

9 Step 3 After the adapter connects to the wireless network successfully, a blue triangle will appear at the front of your wireless network.

Page 11 - Configure Wireless Monitor; Top Menu

10 4. Configure Wireless Monitor This section describes the various functions of the Wireless Monitor that you can configure. Some general functions of this utility will be described here, and the features of each tab will be described in the following sections. Top Menu : Click on the buttons to go...

Page 13 - Delete

12 4.1 Profile The Profile tab lists the current profiles and allows you to manage and create new profiles. The Profile List box lists all the profiles that you’ve created for your networks. You can create a profile for a wireless network you use very often at certain area, such as the wireless netw...

Page 15 - Profile Name; and symbols are allowed, but space is not allowed.; TX Power; : Check the box and you can set RTS threshold manually here. It is

14 Profile Name : Please give this profile a name, up to 32 alphanumerical Characters and symbols are allowed, but space is not allowed. SSID : The SSID of the wireless access point or wireless device you selected will be displayed here. But if the SSID of access point or wireless device is not avai...

Page 16 - Step 4; Select the profile you just created and click; Activate

15 Step 4 Select the profile you just created and click Activate .

Page 17 - : Check this box to accelerate the data transmit rate. It may not work; Enable TCP Window Size; : Check this box and the configuration utility will adjust TCP; Fast Roaming at; : Check this box and you can adjust the threshold of when this; Select Your Country / Region Code; : Select the country / region code of the place

16 4.3 Advanced This wireless network card provides several advanced settings for experienced wireless users. You can change these settings to increase data transfer performance, or change operation mode. Wireless mode : Select wireless mode, only 2.4G (single bandwidth) is available here. Enable TX...

Page 18 - Reset Counter; to reset all counters to zero.

17 4.4 Statistics The Statistics section gives you information about transmit and receive packet count. Click Reset Counter to reset all counters to zero. 4.5 WMM The AWLH6075, Wireless N PCI Card provides QoS (Quality of Service) function, which can improve the performance of certain network applic...

Page 20 - Open the Airlink101 Wireless Monitor. Click the; WPS; method, write down the Pin Code on a piece of paper then click PIN; Push Button; method; Step 3a; Pin Code

19 4.6 WPS (Security Push Button) WPS is a new and easy way to configure the encryption for your wireless network clients. In order to use it, you need to have a router that supports this feature, like the AR675W Airlink101 Wireless N Green Router. You also need to configure the wireless encryption ...

Page 21 - Step 2a; Wireless Router. Open the browser enter; admin; for both the user name and password and click; OK; Click on Wireless > WPS on the left menu bar. Make sure the “; Disable WPS

20 Step 2a If you selected PIN Input method, go to a computer that is connected to your Wireless Router. Open the browser; enter http://192.168.2.1 into the URL address bar. Step 2b Enter admin for both the user name and password and click OK . Step 2c Click on Wireless > WPS on the left menu bar...

Page 22 - Step 2d; Enter the PIN number you just wrote down into the; Client PIN Number; box; Start PIN; router for 3 seconds.

21 Step 2d Enter the PIN number you just wrote down into the Client PIN Number box and click Start PIN . Continue to Step 4 . Step 3a If you selected PBC method, click the Reset/WPS button on the back of the router for 3 seconds. Step 4 The Router will now start the handshake with the wireless adapt...

Page 23 - configuration page and click on; Wireless; . Make sure that Disable

22 Note: If you cannot connect successfully with WPS, you need to log in to your router’s configuration page and click on Wireless . Then click WPS . Make sure that Disable WPS box is unchecked, refer to Step 2c.

Page 25 - About; and the current driver version.

24 4.8 About The About window provides the information about the Wireless Monitor Utility version and the current driver version.

Page 26 - Troubleshooting

25 Troubleshooting 1. If you cannot open the wireless monitor utility, make sure that the PCI adapter is inserted firmly into the PCI slot. 2. If you cannot connect to the wireless router, you may want to double check the wireless security settings on the router. The network key you entered into the...

Page 28 - Technical Support

27 Technical Support E-mail: [email protected] Toll Free: 1-888-746-3238 Web Site: www.airlink101.com *Theoretical maximum wireless signal rate derived from IEEE standard 802.11g and draft 802.11n specifications. Actual data throughput will vary. Network conditions and environmental factors, in...