Page 2 - Table of Contents
2 Table of Contents 1. Introduction ................................................................................................................................. 3 2. Connecting the Router ..............................................................................................................
Page 3 - Equipped with a
3 1. Introduction Congratulations on your purchase of this Super G Wireless Broadband Router. This product is specifically designed for Small Office and Home Office needs. It provides a complete SOHO solution for Internet surfing and is easy to configure and operate even for non-technical users. Ins...
Page 4 - Connecting the Router
4 2. Connecting the Router Note : Prior to connecting the router, be sure to power off your computer, DSL/Cable modem, and the router. You should setup the router with a wired connection first before attempting to setup any wireless connection. Step 1 Connect one end of a network cable to the Intern...
Page 5 - Verifying Connection to the Router
5 3. Verifying Connection to the Router Step 1 Go to Start , Run , type command (for Windows 95/98/ME) or cmd (for Windows 2000/XP) and click OK . You will see the command prompt as below. Step 2 Type ping 192.168.1.1 and press Enter . You should get four reply responses back. Step 3 If you get Requ...
Page 7 - After your IP address is released, click; . You should get an IP address of; Renew
7 Step 8 After your IP address is released, click Renew . You should get an IP address of 192.168.1.x (where x is a number between 2 - 254). If you don’t get an IP address, reset the router by holding in the reset button at the back of the router for 10 seconds while it is ON and try Renew again.
Page 8 - Configuring the Router; Open the web browser and type; Enter; admin; for both the username and password fields and click; OK
8 4. Configuring the Router Step 1 Open the web browser and type 192.168.1.1 in the URL Address field and press Enter . Step 2 Enter admin for both the username and password fields and click OK .
Page 9 - Cable Modem
9 Cable Modem For most cable modem users, you should be able to connect to the Internet without any configuration. If your ISP has provided you with a host name, enter it in the optional Host Name field. Click Apply and OK to save the setting. If your ISP requires a registered MAC Address, click on ...
Page 10 - DSL; Select; PPPoE; Enter your username and password provided by your ISP.; Apply; and; to save the setting.; Troubleshooting
10 DSL For DSL users, follow the steps below to configure the router. Step 1 Select PPPoE from the drop-down menu. Step 2 Enter your username and password provided by your ISP. Note: Depending on the ISP, you may need to include the domain name with your username. Example: [email protected] Ste...
Page 11 - Connecting to the Router Wirelessly; tab. Be sure to click
11 5. Connecting to the Router Wirelessly Below are the default wireless settings of the router. You must configure your wireless network card to the same settings in order to establish a wireless connection to the router. Please refer to your wireless network card’s manual on how to configure these...
Page 12 - Web Configuration Utility; Remember to click; to save your changes.
12 6. Web Configuration Utility This router has a built-in web configuration utility that you can use to configure the router’s settings. Simply log in to the router using your computer’s web browser. 6.1 Setup 6.1.1 Basic Setup This is the default screen when you log in to the router’s web configur...
Page 15 - Enabled; Click the; Clone My PC’s MAC; Click
15 6.1.3 MAC Address Clone Some ISPs require a registered MAC address to access the Internet. You can use the following steps to clone your PC’s registered MAC address to access the Internet. Step 1 Select Enabled from the drop-down menu. Step 2 Click the Clone My PC’s MAC button. Step 3 Click Apply...
Page 16 - To see the current routing table, click on; Show Routing Table; to save each entry.
16 6.1.4 Advanced Routing You can configure your own static routing table using the Advanced Routing function. To see the current routing table, click on Show Routing Table button. Be sure to click Apply and OK to save each entry.
Page 17 - Mode; : You can change the router’s SSID in this field. Once you have; Channel; : Choose to enable or disable the broadcasting of your SSID.
17 6.2. Wireless 6.2.1 Basic Wireless Settings You can configure the router’s basic wireless settings on this screen. Mode : Choose from Wireless-G only, Super G, Mixed, Wireless-B only, or Disabled to disable the Wireless function. Network Name (SSID) : You can change the router’s SSID in this fiel...
Page 18 - WEP
18 6.2.2 Wireless Security You can configure wireless security such as WEP or WPA encryption on this screen. Note : It is recommended that you use WPA encryption over WEP if your wireless clients support WPA. All of the wireless clients must use the same security settings in order to connect to the ...
Page 19 - WPA
19 WPA To enable WPA, select WPA-PSK or WPA2-PSK from the Security Mode . Encryption Methods : Select either TKIP or AES as the encryption method. Passphrase : Enter a passphrase between 8 to 63 characters long. Key Renewal : Enter the desired key renewal time in seconds. Click Apply and OK to save ...
Page 20 - WPA with RADIUS
20 WPA with RADIUS If you are using a RADIUS server in your network for authentication, you may choose WPA or WPA2 from the Security Mode . Encryption Methods : Select either TKIP or AES as the encryption method. RADIUS Server : Enter the IP Address of your RADIUS server. RADIUS Port : Enter the por...
Page 21 - from the drop-down menu and choose whether the specified wireless
21 6.2.3 Wireless MAC Filter You can restrict certain wireless clients from accessing the router by specifying their MAC address and enabling access restriction. Select Enabled from the drop-down menu and choose whether the specified wireless clients will be prevented or permitted to access the wire...
Page 23 - SPI Firewall Protection; : Select to enable or disable Stateful Packet Inspection.; Block Anonymous Internet Requests
23 6.3 Security 6.3.1 Firewall SPI Firewall Protection : Select to enable or disable Stateful Packet Inspection. Block Anonymous Internet Requests : Enable or Disable. Web Filters : You can select to filter Proxy, Java, ActiveX, and/or Cookies. Click Apply and OK to save the setting.
Page 25 - Access Restrictions; Enter Policy Name; : Choose to enable or disable the selected policy.
25 6.4 Access Restrictions 6.4.1 Internet Access Policy You can setup policies that deny or allow specific clients to access the Internet. Enter Policy Name : Enter a name for the policy. Status : Choose to enable or disable the selected policy.
Page 32 - : Select to enable or disable remote management/upgrade of; UPnP; : You can choose to backup the router’s settings so that you don’t
32 6.6 Administration 6.6.1 Management The Management screen allows you to change the router’s log in password as well as other administrative settings. Router Password : Set the router’s log in password. Remote Router Access : Select to enable or disable remote management/upgrade of the router. You...
Page 34 - Ping Test; : Enter the IP or URL Address you wish to ping and click; Start to Ping; : Enter the IP or URL Address you wish to trace and click; Start to Tracer
34 6.6.3 Diagnostics The Diagnostics screen allows you to perform Ping and Traceroute tests. Ping Test : Enter the IP or URL Address you wish to ping and click Start to Ping . Traceroute : Enter the IP or URL Address you wish to trace and click Start to Tracer .
Page 35 - Restore Factory Defaults; button to restore all the settings to default.
35 6.6.4 Factory Defaults The Factory Defaults screen allows you to set all the router’s settings to the factory default. Click on the Restore Factory Defaults button to restore all the settings to default.
Page 36 - You must download and unzip the new firmware first from; Browse; to browse to the new firmware, and click; Start to Upgrade
36 6.6.5 Firmware Upgrade The Firmware Upgrade screen allows you to upgrade the router’s firmware. You must download and unzip the new firmware first from www.airlink101.com Click on Browse to browse to the new firmware, and click Start to Upgrade .
Page 37 - Click on the; Restart; button to restart the router.
37 6.6.6 Restart The Restart page allows you to restart the router without restoring the settings to factory default. Click on the Restart button to restart the router.
Page 38 - Refresh; button to reload the screen.
38 6.7 Status 6.7.1 Router The Router screen displays various status of the router including the firmware version. Click on the Refresh button to reload the screen.
Page 39 - DHCP Client Table; to display a list of all the DHCP clients in your network.
39 6.7.2 LAN The LAN screen displays various status about your Local Area Network. Click on the DHCP Client Table to display a list of all the DHCP clients in your network.
Page 41 - Step 2
41 7. Troubleshooting If you have trouble connecting to the Internet, try the following steps. Step 1 Power off the Cable/DSL modem, router, and computer and wait for 5 minutes . Step 2 Turn on the Cable/DSL modem and wait for the lights on the modem to settle down. Step 3 Turn on the router and wai...
Page 42 - Technical Support
42 Technical Support E-mail: [email protected] Toll Free: 1-888-746-3238 Web Site: www.airlink101.com *Super GTM technology (108 Mbps) can only be obtained when using products with Atheros Super GTM chipset *Theoretical maximum wireless signal rate based on IEEE standard 802.11g specifications....