Airlink101 APSUSB211 - Manuals

4 3. Installing PS Utility Step 1 Insert the provided CD and wait for the autorun screen to appear. Step 2 Click on Install PS Utility . Note: If the autorun screen does not appear automatically, go to Start , Run , type D:\autorun.exe (where D is the letter of your CD drive) and click OK . Step 3 C...

5 Step 4 Click Next . Step 5 Click Yes . Step 6 Click Finish .

6 4. Configuring Network Setting Before configuring the Print Server’s network setting, please take note of your computer’s TCP/IP setting. Step 1 Click on Start , Run , and type command (for Windows 95/98/ME) or cmd (for Windows 2000/XP) and click OK . Step 2 At the command prompt, type ipconfig an...

8 5. Verifying Network Connection Step 1 Run the PS Utility by going to Start , (All) Programs , PS-Utility , PS-Utility v3.00 . Step 2 Make sure the Print Server is detected under the Device Name . Step 3 Click on Show Web Setup to display the Print Server’s Web Configuration Utility . Step 4 Click...

9 Step 5 Click on the Print Test link and click the Test button. The Print Server will perform a low-level print test, bypassing the operating system layer. Note: Your printer should print out a test page. If not, verify that the printer is powered on and all cables are securely connected and try ag...

10 6. Running PS Wizard Warning: Make sure you have installed the printer driver locally on every computer that will use the print server in your network before running the PS Wizard. Otherwise, the PS Wizard will not run properly. Be sure to run the PS Wizard on all the computers that will use the ...

11 Step 3 Click Next . Step 4 Select the printer that is connected to the Print Server and click Next .

13 7. Performing Operating System Print Test The final step in setting up the Print Server is to perform an operating system print test. Please note that the instructions below are for Windows XP, but the steps are similar for all the other Windows operating systems. Step 1 Click on Start , Settings...

14 Step 3 Click on the Print Test Page button. Windows should print out a test page. You have successfully configured the Print Server for printing.

15 8. Using the PS Utility PS Utility is a user-friendly program that allows you to configure some basic functions of the Print Server such as performing a factory reset or updating the firmware. To access the complete management features of the Print Server, you’ll need to use the Web Configuration...

16 9. Using the Web Configuration Utility The Web Configuration Utility allows you to manage the full features of the Print Server with an easy-to-use user interface. You can start the Web Configuration Utility in two ways: 1. Click on the Show Web Setup button in PS Utility . or 2. Open your web br...

17 9.1 Home The Home page displays the status of your Print Server. Click Refresh to update the page.

18 9.2 Setup Wizard The Setup Wizard page allows you to configure some basic settings of the Print Server, including specifying an optional password to log in to the Web Configuration Utility. This page is optional unless you want to setup a password for the Print Server. Server Name : You can chang...

19 IP Address : Select to Manually Assign an IP Address for the Print Server (recommended) or have the router Automatically Assign an IP Address. Click Next to proceed.

20 Workgroup : Enter the name of your Microsoft Network. Click Next to proceed.

21 Second HTTP Port : Select to Enable or Disable a second HTTP port for Remote Web Configuration and IPP Printing. Port Number : You may enter the desired port number for the second HTTP port. Click Next to proceed.

22 Click Yes to save the settings, No to cancel the settings. Note : you may need to re-run the PS Wizard to update these changes.

23 9.3 Change IP Address The Change IP Address page allows you to manually assign an IP Address for the Print Server. The IP Address must be on the same subnet as your network. Click Save to save and activate any configuration changes. Click Cancel to cancel the changes.

24 9.4 Printer Information The Printer Information page shows the status of your printer. Click Refresh to update the page.

25 9.5 Print Test The Print Test page allows you to perform a print test. Click on the Test button to begin the print test. Your printer should print out a test page. If not, verify that the printer is powered on and all cables are securely connected and try again. If the printer still fails to prin...

26 9.6 Factory Reset The Factory Reset page allows you to reset the Print Server to the default factory settings. Click Yes to reset all the settings to factory default.

27 9.7 Firmware Upgrade When a new version of the firmware is available on our web site, www.airlink101.com , you can download the new firmware and proceed to the following page to upgrade the firmware. 1. Click Browse and browse to the location of the downloaded firmware. 2. Click Upgrade to begin ...

28 9.8 About The About page displays the Print Server’s firmware version number.

29 10. Printing in Mac OS This section describes how to set up your Mac OS settings to work with the Print Server. 10.1 Using Rendezvous Mac OS X provides a new feature called Rendezvous . Rendezvous is a networking technology standard that lets you create an instant network of computers and devices...

30 Step 2 Select Rendezvous from the pop-up menu. Step 3 A list of Rendezvous-enabled printers will appear in the list.

31 Step 4 Choose the desired printer and select Generic . Step 5 The printer is installed into the system successfully.

32 11. Appendix Technical Support E-mail: [email protected] Toll Free: 1-888-746-3238 Web site: www.airlink101.com Copyright © 2005 AirLink101. All rights reserved. AirLink101, the stylized AirLink101 logo, specific product designations, and all other words and logos that are identified as trad...