Advantech FPM-3150 Series - Manuals

vii 15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20° C (-4° F) OR ABOVE 60° C (140° F). THIS MAY DAMAGE THE EQUIPMENT. The sound pressure level at the operator's position according to IEC 704-1:1982 is no more than 70dB(A).DISCLAIMER: This se...

ix Table of Contents Contents Chapter 1 Introduction ..................................................... 2 1.1 Introduction ................................................................................. 21.2 Specifications............................................................................

2 CHAP T ER 1 Introduction This chapter includes: • Introduction• Specifications• LCD Specification• Power Consumption• Connectors• Dimensions

FPM-3150 Series User Manual 2 Chapter 1 Introduction 1.1 Introduction Advantech's FPM-3150 is a 15" color TFT LCD flat panel monitor built specifically for industrial applications. With the optional touchscreen, FPM-3150 is an excellent and user-friendly system control interface.In addition to i...

3 Chapter 1 Touchscreen (Optional) • Type: 8 wire, analog resistive • Resolution: 1024 x 1024 • Light Transmission: 75% (Gouge Hardness is greater tahn 4H per ASTM D3363-92 for HCC01, HCG10 and HCG12 • Operating Pressure: 30 ~ 45 gram for stylus pen contact bounce < 10 ms • Controller: RS-232 int...

FPM-3150 Series User Manual 4 1.5 Connectors The following connectors are situated on the left hand side of the FPM-3150 Series: VGA Port (DB-15) This DB-15 connector can be connected to the system via the external 15-pin DB-15 connector locatd on the left side of the system unit. Touchscreen Connec...

2 CHAP T ER 2 Mounting • Wall Mounting• Panel Mounting• Rack Mounting• Desktop Mounting• Swing Arm Mounting

FPM-3150 Series User Manual 8 Chapter 2 Mounting 2.1 Mounting the Monitor The FPM-3150 Series can be mounted in many different ways. The ver-satility of the FPM-3150 mounts enable it to be mounted on your desk or anywhere else. 2.1.1 Wall Mounting FPM-3150 can be mounted directly on a wall with pane...

FPM-3150 Series User Manual 10 2.1.3 Rack Mounting (Optional) If you need to install the FPM-3150 on a rack, you must order the rack mount kit for FPM-3150 (Part Number is FPM-3150Rack-MT). Attach the two rack mounting brackets on each side of FPM-3150 with 12 screws, then affix the monitor in the r...

2 APPENDIX A Touchscreen This appendix contains information on the touchscreen, its installation and configuration.

FPM-3150 Series User Manual 14 Appendix A Touchscreen A.1 Introduction The FPM-3150 Series’ optional touchscreen uses advanced 8-wire resis-tive technology. It provides more accurate sensing capacity than other technologies. The touchscreen is specially designed for tough industrial environments, an...

15 Appendix A Optical • Visible light transmission: 75% typical (>74% @ 550 nm test) • Clarity: Clear Finish - 25%, Antiglare Finish - 15% Sensor board • Chemical strengthened glass with 4 H hardness standard. (Test condition: ASTM D3363-92A) Ball drop test • Able to bear a 225 g steel ball dropp...

FPM-3150 Series User Manual 18 4. A License Agreement appears. Click “I accept…” and “Next” 5. The “Ready to Install the Program” screen appears. Select “Install.”

19 Appendix A 6. The next screen is “Hardware Installation.” Select “Continue Any-way.” 7. The “InstallShield Wizard Completed” appears. Click “Finish.”

FPM-3150 Series User Manual 20 A.4 Configuring PenMount Windows 2000/XP Driver Upon rebooting, the computer automatically finds the new 9000 control-ler board. The touch screen is connected but not calibrated. Follow the procedures below to carry out calibration.1. After installation, click the PenM...

FPM-3150 Series User Manual 24 Draw Tests or demonstrates the PenMount touch screen operation. The display shows touch location. Click Draw to start. Touch the screen with your finger or a stylus and the drawing screen registers touch activity such left, right, up, down, pen up, and pen down. Touch ...

25 Appendix A Multiple Monitors Multiple Monitors supports from two to six touch screen displays for one system. The PenMount drivers for Windows 2000/XP support Multiple Monitors. This function supports from two to six touch screen displays for one system. Each monitor requires its own PenMount tou...

FPM-3150 Series User Manual 26 2. When the mapping screen message appears, click OK. 3. Touch each screen as it displays “Please touch this monitor.” Fol-lowing this sequence and touching each screen is called mapping the touch screens .

27 Appendix A 4. Touching all screens completes the mapping and the desktop reap-pears on the monitors. 5. Select a display and execute the ‘Calibration’ function. A message to start calibration appears. Click OK. 6. “Touch this screen to start its calibration” appears on one of the screens. Touch t...

FPM-3150 Series User Manual 28 Option This panel function supports two modes—Operation Mode and Beep Sound Mode—which allow configuration for specific touch screen appli-cations, such as point-of-sales (POS) terminals. NOTE: 1. If you used a single VGA output for multiple monitors, please do not use...

29 Appendix A About This panel displays information about the PenMount controller and driver version.

FPM-3150 Series User Manual 30 A.4.2 PenMount Monitor Menu Icon The PenMount monitor icon (PM) appears in the menu bar of Windows 2000/XP system when you turn on PenMount Monitor in PenMount Util-ities. PenMount Monitor has the following functions. Beep Turns beep on or off. Right Button When you se...

31 Appendix A A.4.3 PenMount Rotating Functions The PenMount driver for Windows 2000/XP supports several display rotating software packages. Please see Chapter 5 for more information. The PenMount drivers for Windows 95, Windows 98/Me, Windows 2000/XP, as well as Windows 98 USB and Windows Me/2000/X...

FPM-3150 Series User Manual 32 A.5 Uninstall the PenMount Windows 2000/XP driver 1. Exit the PenMount monitor (PM) in the menu bar. 2. Go to Settings, then Control Panel, and then click Add/Remove program. Select PenMount DMC9000 and click the Add/Remove button. 3. Select PenMount DMC9000 and DMC910...

FPM-3150 Series User Manual 34 Appendix B Standard Timing Set Serial Data for Expansion B.1 Setting serial data for expansion The twelve kinds of timings below are already programmed in this mod-ule. The input synchronous signals are automatically recognized. Resolution Vertical Frequencies56 Hz 60 ...

2 APPENDIX C OSD • OSD Selection• Keypad Interface• OSD Function

FPM-3150 Series User Manual 36 Appendix C OSD C.1 Keypad Interface C.2 Power Indicator LED Status The keypad interface provides a driver for a dual color LED to indicate status.(1) Green: COMMON board detects a input signal and sends output sig-nal to LCD panel.(2) Orange: No signal detected, or out...

37 Appendix C C.3 OSD Function Each selected value is stored into LCD memory after SEL signal input or time out. The stored values are not affected if the power is turned off. But the selected value is not available in case a selected mode is changed before time out or power is turned off before tim...