Page 2 - Copyright Notice
FPM-3150 Series User Manual ii Copyright Notice This document is copyrighted by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements to the products described in this manual at any time. Specifications are thus subject to change without notice.No p...
Page 4 - FCC Class B; to which the receiver is connected
FPM-3150 Series User Manual iv FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-ence when the equipment is operated in...
Page 6 - Safety Instructions; Read these safety instructions carefully.
FPM-3150 Series User Manual vi Safety Instructions 1. Read these safety instructions carefully. 2. Keep this User's Manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for clean-ing. 4. For plug-in equip...
Page 7 - Wichtige Sicherheishinweise; Bitte lesen sie Sich diese Hinweise sorgfältig durch.
vii 15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20° C (-4° F) OR ABOVE 60° C (140° F). THIS MAY DAMAGE THE EQUIPMENT. The sound pressure level at the operator's position according to IEC 704-1:1982 is no more than 70dB(A).DISCLAIMER: This se...
Page 9 - Contents; Chapter
ix Table of Contents Contents Chapter 1 Introduction ..................................................... 2 1.1 Introduction ................................................................................. 21.2 Specifications............................................................................
Page 11 - Introduction; This chapter includes:
2 CHAP T ER 1 Introduction This chapter includes: • Introduction• Specifications• LCD Specification• Power Consumption• Connectors• Dimensions
Page 12 - Chapter 1 Introduction; General; Heavy-duty aluminum and steel chassis
FPM-3150 Series User Manual 2 Chapter 1 Introduction 1.1 Introduction Advantech's FPM-3150 is a 15" color TFT LCD flat panel monitor built specifically for industrial applications. With the optional touchscreen, FPM-3150 is an excellent and user-friendly system control interface.In addition to i...
Page 13 - LCD Specification; Storage Temperature:; Power Consumption
3 Chapter 1 Touchscreen (Optional) • Type: 8 wire, analog resistive • Resolution: 1024 x 1024 • Light Transmission: 75% (Gouge Hardness is greater tahn 4H per ASTM D3363-92 for HCC01, HCG10 and HCG12 • Operating Pressure: 30 ~ 45 gram for stylus pen contact bounce < 10 ms • Controller: RS-232 int...
Page 14 - DC 12V Power In
FPM-3150 Series User Manual 4 1.5 Connectors The following connectors are situated on the left hand side of the FPM-3150 Series: VGA Port (DB-15) This DB-15 connector can be connected to the system via the external 15-pin DB-15 connector locatd on the left side of the system unit. Touchscreen Connec...
Page 17 - Mounting
2 CHAP T ER 2 Mounting • Wall Mounting• Panel Mounting• Rack Mounting• Desktop Mounting• Swing Arm Mounting
Page 18 - Chapter 2 Mounting; Mounting the Monitor; Screw the hook and panel-mount brackets on the wall.
FPM-3150 Series User Manual 8 Chapter 2 Mounting 2.1 Mounting the Monitor The FPM-3150 Series can be mounted in many different ways. The ver-satility of the FPM-3150 mounts enable it to be mounted on your desk or anywhere else. 2.1.1 Wall Mounting FPM-3150 can be mounted directly on a wall with pane...
Page 20 - Figure 2.3: Rack Mounting by Rack Mounting Brackets
FPM-3150 Series User Manual 10 2.1.3 Rack Mounting (Optional) If you need to install the FPM-3150 on a rack, you must order the rack mount kit for FPM-3150 (Part Number is FPM-3150Rack-MT). Attach the two rack mounting brackets on each side of FPM-3150 with 12 screws, then affix the monitor in the r...
Page 23 - APPENDIX; Touchscreen
2 APPENDIX A Touchscreen This appendix contains information on the touchscreen, its installation and configuration.
Page 24 - Appendix A Touchscreen; A.2 Touchscreen Specifications; Electrical; Hard coating is highly resistant to most solvents and chemicals
FPM-3150 Series User Manual 14 Appendix A Touchscreen A.1 Introduction The FPM-3150 Series’ optional touchscreen uses advanced 8-wire resis-tive technology. It provides more accurate sensing capacity than other technologies. The touchscreen is specially designed for tough industrial environments, an...
Page 25 - • Chemical strengthened glass with 4 H hardness standard.; A.3 Installing Driver for Windows 2000/XP
15 Appendix A Optical • Visible light transmission: 75% typical (>74% @ 550 nm test) • Clarity: Clear Finish - 25%, Antiglare Finish - 15% Sensor board • Chemical strengthened glass with 4 H hardness standard. (Test condition: ASTM D3363-92A) Ball drop test • Able to bear a 225 g steel ball dropp...
Page 28 - A License Agreement appears. Click “I accept...” and “Next”
FPM-3150 Series User Manual 18 4. A License Agreement appears. Click “I accept…” and “Next” 5. The “Ready to Install the Program” screen appears. Select “Install.”
Page 29 - The “InstallShield Wizard Completed” appears. Click “Finish.”
19 Appendix A 6. The next screen is “Hardware Installation.” Select “Continue Any-way.” 7. The “InstallShield Wizard Completed” appears. Click “Finish.”
Page 30 - A.4 Configuring PenMount Windows 2000/XP Driver; When the PenMount Control Panel appears, click “Calibrate.”; Calibrate
FPM-3150 Series User Manual 20 A.4 Configuring PenMount Windows 2000/XP Driver Upon rebooting, the computer automatically finds the new 9000 control-ler board. The touch screen is connected but not calibrated. Follow the procedures below to carry out calibration.1. After installation, click the PenM...
Page 34 - Draw; Click Clear Screen to clear the drawing.
FPM-3150 Series User Manual 24 Draw Tests or demonstrates the PenMount touch screen operation. The display shows touch location. Click Draw to start. Touch the screen with your finger or a stylus and the drawing screen registers touch activity such left, right, up, down, pen up, and pen down. Touch ...
Page 35 - Multiple Monitors; Check the; Enable Multiple Monitor Support; to assign touch controllers to displays.
25 Appendix A Multiple Monitors Multiple Monitors supports from two to six touch screen displays for one system. The PenMount drivers for Windows 2000/XP support Multiple Monitors. This function supports from two to six touch screen displays for one system. Each monitor requires its own PenMount tou...
Page 36 - When the mapping screen message appears, click OK.; mapping
FPM-3150 Series User Manual 26 2. When the mapping screen message appears, click OK. 3. Touch each screen as it displays “Please touch this monitor.” Fol-lowing this sequence and touching each screen is called mapping the touch screens .
Page 37 - Continue calibration for each monitor by clicking; bration; and touching the red squares.
27 Appendix A 4. Touching all screens completes the mapping and the desktop reap-pears on the monitors. 5. Select a display and execute the ‘Calibration’ function. A message to start calibration appears. Click OK. 6. “Touch this screen to start its calibration” appears on one of the screens. Touch t...
Page 38 - Option
FPM-3150 Series User Manual 28 Option This panel function supports two modes—Operation Mode and Beep Sound Mode—which allow configuration for specific touch screen appli-cations, such as point-of-sales (POS) terminals. NOTE: 1. If you used a single VGA output for multiple monitors, please do not use...
Page 39 - About
29 Appendix A About This panel displays information about the PenMount controller and driver version.
Page 40 - PenMount Monitor has the following functions.
FPM-3150 Series User Manual 30 A.4.2 PenMount Monitor Menu Icon The PenMount monitor icon (PM) appears in the menu bar of Windows 2000/XP system when you turn on PenMount Monitor in PenMount Util-ities. PenMount Monitor has the following functions. Beep Turns beep on or off. Right Button When you se...
Page 41 - Configuring the Rotate Function; Install the rotation software package.; party
31 Appendix A A.4.3 PenMount Rotating Functions The PenMount driver for Windows 2000/XP supports several display rotating software packages. Please see Chapter 5 for more information. The PenMount drivers for Windows 95, Windows 98/Me, Windows 2000/XP, as well as Windows 98 USB and Windows Me/2000/X...
Page 42 - A.5 Uninstall the PenMount Windows 2000/XP driver
FPM-3150 Series User Manual 32 A.5 Uninstall the PenMount Windows 2000/XP driver 1. Exit the PenMount monitor (PM) in the menu bar. 2. Go to Settings, then Control Panel, and then click Add/Remove program. Select PenMount DMC9000 and click the Add/Remove button. 3. Select PenMount DMC9000 and DMC910...
Page 44 - Appendix B Standard Timing Set Serial; B.1 Setting serial data for expansion
FPM-3150 Series User Manual 34 Appendix B Standard Timing Set Serial Data for Expansion B.1 Setting serial data for expansion The twelve kinds of timings below are already programmed in this mod-ule. The input synchronous signals are automatically recognized. Resolution Vertical Frequencies56 Hz 60 ...
Page 45 - OSD
2 APPENDIX C OSD • OSD Selection• Keypad Interface• OSD Function
Page 46 - Appendix C OSD; C.1 Keypad Interface
FPM-3150 Series User Manual 36 Appendix C OSD C.1 Keypad Interface C.2 Power Indicator LED Status The keypad interface provides a driver for a dual color LED to indicate status.(1) Green: COMMON board detects a input signal and sends output sig-nal to LCD panel.(2) Orange: No signal detected, or out...
Page 47 - Main Menu Sub Menu
37 Appendix C C.3 OSD Function Each selected value is stored into LCD memory after SEL signal input or time out. The stored values are not affected if the power is turned off. But the selected value is not available in case a selected mode is changed before time out or power is turned off before tim...
