Page 3 - FCC Class A notes
FCC Class A notes This equipment has been tested with a class A computing device andhas been found to comply with part 15 of FCC Rules. Operation in aresidential area may cause unacceptable interference to radio and TVreceptions requiring the operator to take whatever steps are necessaryto correct t...
Page 4 - Safety Instructions
Safety Instructions 1 . Read these safety instructions carefully. 2 . Keep this installation reference guide for later reference. 3 . Disconnect this equipment from any AC outlet before cleaning. Do not useliquid or spray detergents for cleaning. Use a damp cloth. 4 . For pluggable equipment, the po...
Page 5 - Wichtige Sicherheishinweise
Wichtige Sicherheishinweise 1 . Bitte lesen sie Sich diese Hinweise sorgfältig durch. 2 . Heben Sie diese Anleitung für den späteren Gebrauch auf. 3 . Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden SieKeine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuchzu...
Page 6 - Contents
Contents Chapter 1 General Information ..................................... 1 1 . 1 Introduction ....................................................................... 2 1 . 2 Specifications .................................................................... 2General ................................
Page 11 - General Information; CHAPTER
General Information This chapter gives backgroundinformation on the HMI-640S. Sections include: • Introduction • Specifications • LCD Specifications • I/O Arrangement • Total Solution • Dimensions • Mounting CHAPTER 1
Page 12 - General; • Construction: Plastic molding with an optional PC/104 metal; cover; • CPU with core logic: STPC Client 66MHz, which is equivalent to 66
2 HMI-640S User's Manual 1.1 Introduction The HMI-640S meets all of the requirements necessary to serve asan industrial operator interface. This panel PC provides an all-in-one486 PC platform with 6.0" STN color LCD display, on-board VGA,two COM ports (one RS-232, one RS-232/422/485), one remova...
Page 13 - • RAM: 16MB EDO RAM on board
Chapter 1 General Information 3 • RAM: 16MB EDO RAM on board • IDE hard disk drive interface: Supports up to two Enhanced IDE devices, auto-detect BIOS • Multi-mode parallel port: Configured to LPT1, LPT2, LPT3 or disabled. Supports SPP/EPP/ECP; D-SUB 25-pin connector (on I/Omodule) • Serial ports: ...
Page 14 - Environmental specifications
4 HMI-640S User's Manual Ethernet interface • Chipset: Realtek RTL8139A 10/100 Base-T controller • Network (LAN): Novell NE1000/2000 compatible. Supports both boot ROM function and software drivers SVGA/Flat panel interface (CPC-2520) • Chipset: C&T 69000 • Display memory: 2 MB SDRAM embedded • ...
Page 15 - Touchscreen; • Software driver: HMI-640S supports both DOS and Windows CE; LCD Specifications
Chapter 1 General Information 5 M o d e l H M I - 6 4 0 S D i s p l a y t y p e S T N c o l o r L C D M a x . c o l o r s o rg r a y s c a l e s 2 5 6 c o l o r s S i z e 6 . 0 " L C D m o d e l K C B 0 6 0 V G 1 C A - A 2 1 o r c o m p a t i b l e R e s o l u t i o n 6 4 0 x 4 8 0 ( V G A ) B r...
Page 16 - mouse connector; input connector
6 HMI-640S User's Manual 1.4 I/O Arrangement The I/O arrangement of the HMI-640S is shown below: Note: Serial por t COM2 can be configured to operate inRS-232, RS-422 or RS-485 mode. This is set by DIPswitches on the upper side of the back cover. Beforeattaching connectors, please make sure the DIPs...
Page 21 - System Setup
System Setup This chapter explains how to set up the HMI-640S hardware. Sections include: • General • Packing List • Initial Setup • Installing a CompactFlash memory card • Connecting the Power Adapter • Installing a PC/104 Module • First System Boot • Exploded Diagram CHAPTER 2
Page 22 - Verify that power source has been disconnected
1 2 HMI-640S User's Manual 2.1 General The HMI-640S compact profile panel PC can simultaneously monitorand sample the data from several traditional PLC controllers. It takesfull advantage of a wide range of available software programs, and itsupgrade can be performed both quickly and easily with the...
Page 23 - Before installing the serial port mouse driver, you; Step 3: Turn the sytem power on for the first boot.
Chapter 2 System Setup 1 3 Warning! Before installing the serial port mouse driver, you must remove the PS/2 mouse driver from yoursystem. Note: The PS/2 mouse driver cannot be simultaneouslyinstalled with a serial/COM port mouse driver. Note: It might be possible that you may see several light orda...
Page 24 - Installing a CompactFlash Memory Card; Installing a CompactFlash adapter; Verify that the power source to the HMI-640S has been properly; Make sure your CompactFlash memory card is inserted properly
1 4 HMI-640S User's Manual 2.3 Installing a CompactFlash Memory Card Installing a CompactFlash adapter 1. Verify that the power source to the HMI-640S has been properly disconnected. 2. Insert the CompactFlash adapter frimly but gently into the IDE- compatible slot as shown in the picture below. 3. ...
Page 26 - Connecting the Power Adapter; power receptable
1 6 HMI-640S User's Manual 2.4 Connecting the Power Adapter Before connecting the power adapter to your HMI-640S, you must firstattach the Power Terminal Block onto the 24 V DC power receptable located beneath the HMI-640S. After the Power Terminal Block hasbeen attached, you can then connect the po...
Page 29 - First System Boot; Power up for the first time; Please follow the steps below to perform your first system boot :; Assign the Device Name; Follow the instructions below to assign the Device Name:
Chapter 2 System Setup 1 9 2.6 First System Boot After you have properly installed the CompactFlash memory card pre-installed with Windows CE or even with specific application software ,all you have to do is simply plug in the power and the system is readyfor the first boot. Power up for the first t...
Page 31 - Maintenance; • Removing the Front/Rear Panel
CHAPTER Maintenance The HMI-640S is of a modular design sothat it is convenient for users to maintainor service its internal components. Thischapter will describe the disassemblingprocess for the machine. Sections include: • Removing the Front/Rear Panel • LCD Display • LCD Backlight • Power Supply ...
Page 35 - The backlight is fragile. Use caution when handling
Chapter 3 Maintenance 2 5 3.3 LCD Backlight To replace the backlight: 1. Verify that the power source to the HMI-640S has been disconnect- ed. 2. Open the front panel. (See Section 3.1.) 3. Remove the LCD from the steel chassis. 4. Disconnect the cables from the LCD and the LCD inverter. 5. Remove t...
Page 36 - Warning: Shut off power to the HMI-640S before attempting to
2 6 HMI-640S User's Manual 3.4 Power Supply To repair or replace the power supply: 1. Verify that the power source to the HMI-640S has been disconnect- ed. 2. Open the rear cover. (See Section 3.1) 3. Remove the four screws attaching the power supply to the CPU board. 4. Disconnect the cable from th...
Page 37 - Verify that the power source to the HMI-640S has been disconnect-
Chapter 3 Maintenance 2 7 3.5 I/O Adapter (CPC-2900) To replace or service the I/O adapter, follow these steps: 1. Verify that the power source to the HMI-640S has been disconnect- ed. 2. Remove the rear cover. (See Section 3.1.) 3. Remove the screw which attaches the I/O adapter to the Carrier Boar...
Page 39 - This chapter provides:
CHAPTER CPC-2245N Main Board This chapter provides: • Background information such as cardspecification and board layout of CPC-2245N. • The installation procedures for CPC-2245N hardware, including instructions onsetting jumpers and connecting peripher-als, switches and indicators. Be sure toread al...
Page 40 - Introduction; without the
3 0 HMI-640S User's Manual 4.1 Introduction Advantech’s new mini biscuit PC, the CPC-2245N, is truly an all-inone 486 processor-based single board computer. It comes equippedwith 16 MB DRAM on board, an SVGA interface which supportsCRT monitors with up to 4 MB display memory, a 10/100Base-TEthernet ...
Page 41 - Specifications; • BIOS: 256 KB Flash BIOS; emulated HDD; • Enhanced IDE hard disk drive interface: Supports up to two
Chapter 4 CPC-2245N Main Borad 31 4.2 Specifications • CPU: STPC Client, 66 MHz • On-card cache: 8 KB • BIOS: 256 KB Flash BIOS • Chipset: STPC Client • Super I/O chipset: Winbond W83977F • RAM memory: 16 MB EDO RAM on board • Solid state disk: Supports one CompactFlash card as an emulated HDD • Wat...
Page 42 - • VGA with 64-bit windows accelerator; interface; • Power connector: 4-pin mini power connector; Mechanical and environmental
3 2 HMI-640S User's Manual VGA/LAN/serial port/keyboard/mouse (40-pin FPCconnector) • VGA with 64-bit windows accelerator -Display memory: 4 MB share memory architecture (UMA structure) -Display resolution: 1280 x 1024 @ 64 K colors, 1024 x 768 @ 16 M colors -Automatically disables internal VGA if a...
Page 43 - Board layout: dimensions
Chapter 4 CPC-2245N Main Borad 33 4.3 Board layout: dimensions
Page 44 - Jumpers and connectors; Name
3 4 HMI-640S User's Manual 4.4 Jumpers and connectors On-board connectors link to external devices such as hard diskdrives, keyboards, floppy drives, and so on. In addition, the boardhas jumpers for configuring your board for specific applications. The table below lists the function of each of the b...
Page 46 - Safety precautions; Always completely disconnect the power cord from
3 6 HMI-640S User's Manual 4.6 Safety precautions Warning! Always completely disconnect the power cord from your chassis whenever you are working on it. Donot make connections while the power is onbecause sensitive electronic components can bedamaged by the sudden rush of power. Onlyexperienced elec...
Page 47 - Setting jumpers; Open
Chapter 4 CPC-2245N Main Borad 37 4.7 Setting jumpers You may configure your card to match the needs of your applica-tion by setting jumpers. A jumper is the simplest kind of electricalswitch. It consists of two metal pins and a small metal clip (oftenprotected by a plastic cover) that slides over t...
Page 48 - Function
3 8 HMI-640S User's Manual 4.7.1 Clear CMOS (J2) This jumper is used to erase CMOS data and reset system BIOSinformation. The procedure for clearing CMOS is: 1. Turn off the system. 2. Short pin 2 and pin 3. 3. Turn on the system. The CMOS is now cleared. 4. Turn off the system. Short pin 1 and pin ...
Page 53 - ISA bus
Chapter 4 CPC-2245N Main Borad 43 Table 4-5: ISA bus - CN3 cross reference table (ISA bus pin B) ISA bus CN3 Pin Signal Pin Signal B1 G N D 9 G N D B2 RSTDRV 7 5 RSTDRV B3 +5 V 1 +5 V B4 IRQ9 8 9 IRQ9 B5 -5 V - - B6 D R Q 2 9 9 D R Q 2 B7 -12 V - - B8 0 WS 2 ZW B9 +12 V - - B 1 0 G N D 1 0 G N D B 1...
Page 57 - IDE pin 28 must pull 470 ohms resistor to GND.
Chapter 4 CPC-2245N Main Borad 47 Note : IDE pin 28 must pull 470 ohms resistor to GND. Note : 33 ohms damping resistors is recommended toconnect near IDE connector. Please refer to Fig.2-2 below. Note : We do not recommend connection to the followingIDE HDD models of Seagate: ST 31276A, ST31720A, S...
Page 65 - Pin
Chapter 4 CPC-2245N Main Borad 55 4.11 Power supply connector (CN5) In single board computer without carrier applications, user mayconnect a power directly to the CPC-2245N board through CN5. Seethe following table for its pin assignments: Table 4-19: Power supply connector (CN5) Pin Function 1 N C ...
Page 66 - Card installation
Page 68 - FPC cable installation
5 8 HMI-640S User's Manual 4.14 FPC cable installation
Page 71 - • Flat panel VGA interface; • Chipset: C&T 69000 VGA controller with Windows accelerator
Chapter 5 CPC-2520 VGA/LCD Control Board 61 5.2 Specifications General • Flat panel VGA interface • Chipset: C&T 69000 VGA controller with Windows accelerator • Display memory: 2 MB SDRAM in built-in chip • Display output: 50-pin FPC connector for flat panel interface12-pin FPC connector for VGA...
Page 73 - Number
Chapter 5 CPC-2520 VGA/LCD Control Board 63 5.4 Jumpers and connectors On-board connectors link to external devices such as hard diskdrives, keyboards, or floppy drives, etc. In addition, the board hasjumpers for configuring your board for specific applications. The table below lists the function of...
Page 76 - Jumper settings
6 6 HMI-640S User's Manual 5.7 Jumper settings You configure your card to match the needs of your application bysetting jumpers. A jumper is the simplest kind of electric switch. Itconsists of two metal pins and a small metal clip (often protectedby a plastic cover) that slides over the pins to conn...
Page 77 - Panel Type
Chapter 5 CPC-2520 VGA/LCD Control Board 67 5.8 LCD panel select (SW1) 5.9 Display connectors (CN2, CN3) The CPC-2520 PCI SVGA interface can drive conventional CRTdisplay and is capable of driving a wide range of flat display,including electroluminescent (EL), gas plasma, passive LCD, andactive LCD ...
Page 81 - FPC cable installation
Chapter 5 CPC-2520 VGA/LCD Control Board 71 5.12 FPC cable installation
Page 84 - Networking via LAN
7 4 HMI-640S User's Manual 6.1 Introduction The HMI-640S is designed as a networking gadget that readilyconnect itself to the host PC either via existing LAN or a RS-232interface. Its network capability makes it nothing less than a powerfulplatform for any application that demands networking communi...
Page 87 - Double-click the New Connection icon to connect to the PC.; Simple Networking via a Hub
Chapter 6 Networking Communication 7 7 Note: Be sure to power off the HMI-640S before youconnect or disconnect any cable. 3. Power up your HMI-640S and after the system boot has complet-ed, try access Start/Programs/Communication/Remote Networkingproperties sheet. 4. Click Make New Connection to pop...
Page 89 - Cabling for RS-232 Port; APPENDIX
Cabling for RS-232 Port The HMI-640S is equipped with a watchdogtimer that resets the CPU if processingcomes to a standstill for any reason. Thisfeature ensures system reliability in industri-al stand-alone or unmanned environments. APPENDIX A
Page 93 - DIP Switch Settings; • Touchscreen Specifications
B APPENDIX DIP Switch Settings • Touchscreen Specifications • Installation • Running the Setup Program • Removing the Touchscreen Driver • Touchscreen Driver Application Interface (API)
Page 94 - B.1 Touchscreen Specifications; D IP Switch Se tting
8 4 HMI-640S User's Manual B.1 Touchscreen Specifications The touchscreen is a 4-wire analog resistive type. It is constructed ofone glass sheet overlayed with two layers of PET. The PET layers arecoated with ITO and are separated by printed spacers. The touch-screen is designed to be activated by t...
