Bosch WFL 2060UC Manual — Free PDF Download

Page 3 - loading and unloading)

Features and Benefits Features and Benefits 3 • • Larger door Larger door - - 25% larger vs. WFK 2401 25% larger vs. WFK 2401 • • Larger opening Larger opening - - 15% larger vs. WFK 2401 (easier 15% larger vs. WFK 2401 (easier loading and unloading) loading and unloading) • • Larger drum Larger dru...

Page 4 - Sensotronic; (displays actual time of day cycle stops)

Extra Features and Benefits Extra Features and Benefits -- -- WFR 2460 WFR 2460 • • Continuous cycle notification Continuous cycle notification - - digital display digital display • • Sensotronic Sensotronic II Plus II Plus electronic control electronic control • • Accurate water level control indep...

Page 6 - Bosch Washers and Dryers Limited Lifetime Warranty; Statement of Limited Warranty

Bosch Washers and Dryers Limited Lifetime Warranty Statement of Limited Warranty The warranties provided by BSH Home Appliances ("Bosch") in this Statement of Warranties apply only to Bosch clothes washers and dryers sold to the first using purchaser by Bosch or its authorized dealers, retai...

Page 7 - For location of nearest repair depot call 1

Warranty (2) Warranty (2) 5 Year Limited Warranty On Electronics Bosch will repair or replace, free of charge, any microprocessor or printed circuit board that proves defective under conditions of normal home use for a period of five years from the date of original installation, labor charges exclud...

Page 8 - label; To find when the product type

Warranty Warranty -- -- Serial # Label Serial # Label The serial # label, located on the rear of the washer, shows necessary warranty information. 8 6 6 Serial # label • Model # - “WFR2460UC/01”. 1st Edition/Revision 5 (1/20/04) • Serial # - “FD 8108”. To find when the product type was built, add 20...

Page 9 - Reprint of Installation Instructions; Be sure to follow all

Installation Installation -- -- Reprint of Installation Instructions Reprint of Installation Instructions 1st Edition/Revision 5 (1/20/04) NOTE: Be sure to follow all national & local codes. Flat (blade) screwdriver. HINT: Cold & hot water connections are clearly marked on the rear of the wa...

Page 10 - To avoid damaging washer, don’t move it; Installation

1st Edition/Revision 5 (1/20/04) HINT: To avoid damaging washer, don’t move it while the feet (leveling legs) are extended. Installation Installation -- -- Reprint of Installation Instructions Reprint of Installation Instructions L L ; 10

Page 14 - Fascia Panels

Operation Operation -- -- Fascia Panels Fascia Panels 14 WFL 2060UC WFR 2460UC 1st Edition/Revision 5 (1/20/04)

Page 15 - Controls; Both have

Operation Operation -- -- Controls 15 Controls Both have Regular/Cotton , Permanent Press , Delicates , Hand Washables , Temperature Boost & Power Temperature Boost settings. Spin Speed Selector knob Special Wash Buttons Digital Display WFR 2460UC WFL 2060UC 1st Edition/Revision 5 (1/20/04)

Page 17 - Mechanical Pressure Switch; measures the water; Analog Pressure Switch -; • Precise measuring of actual water level; Continuous adjustment of wash times

Operation Operation -- -- Sensors (2) Sensors (2) 17 Mechanical Pressure Switch - (WFL 2060UC & WFR 2460 UC) measures the water level after the first fill. If the water level is high (like for smaller loads), the pressure increases and the pressure switch does not provide more water. Analog Pres...

Page 18 - Exact monitoring of water inflow.; BENEFITS: Minimizes water consumption

18 Operation Operation -- -- Sensors (3) Sensors (3) 1A/1B. Flow Meter ¾ Exact monitoring of water inflow. ¾ Ensures exact control of water inlet valves so that there is always the right amount of water for wash and rinse cycles. ¾ Together with the pressure switch, there is a continuous adjustment ...

Page 19 - Propeller emits signals; independent from water pressure; Water; An; internal water clock; monitors water inflow via soak compartment.

19 Operation Operation -- -- Sensors (4) Sensors (4) Propeller emits signals ( independent from water pressure ) Water 9 An internal water clock monitors water inflow via soak compartment. 9 Ensures exact control of water inlet valves - always right amount of water. 9 Independent from water pressure...

Page 20 - Digital Temperature Sensor

Operation Operation -- -- Sensors (5) Sensors (5) 20 2. Digital Temperature Sensor Both models are equipped with the Temperature Sensor to deliver guaranteed wash temperatures Thermostat & Heating Element 1st Edition/Revision 5 (1/20/04)

Page 22 - Unbalanced Load Sensor; Accurate measuring of unbalance by

Operation Operation -- -- Sensors (7) Sensors (7) 22 4. Unbalanced Load Sensor 9 Accurate measuring of unbalance by deviation of spin speed and slow down time of drum 9 Infinite adapting of spin speeds 9 Compensates reducing of spin speeds by prolonging spinning times 9 Will attempt up to 15 times t...

Page 23 - Spin spe; III; load distribution; dangerous

Operation Operation -- -- Sensors (8) Sensors (8) 23 4. Unbalanced Load Sensor Spin spe ed [r pm] 0 200 400 600 800 1000 1200 max. 15 trials III IV II I load distribution unbalance Spin spee d (rpm) spinning profile good small 1200 (max.) I uneven medium 1000 (reduced) II bad big 800 (low) III none ...

Page 24 - Cleaning Drain Pump Trap

Operation Operation -- -- Cleaning Drain Pump Trap Cleaning Drain Pump Trap 24 Larger objects such as coins and paper clips are collected in the drain pump trap so they won’t plug up or damage other parts of the washer. The drain pump trap can easily be cleaned by customers. 1st Edition/Revision 5 (...

Page 28 - To access the drum, the front panel must be removed first.

Disassembly Disassembly -- -- Drum (1), Top Panel Drum (1), Top Panel 28 To access the drum, the front panel must be removed first. 2 2 1 2 2 TO REMOVE FRONT PANEL (to access drum): • c Remove top panel. • d To remove fascia panel, first remove T-10 Torx screw on right endcap and T-20 Torx screws on...

Page 29 - Disassembly

4 6 5 4 TO REMOVE FRONT PANEL (continued): • f Carefully loosen door seal clamping rings (outer/inner), taking care not to tear seal. Loosen clamp and disconnect water fill tube from seal, then remove seal. • g Remove two T-20 Torx front panel screws from bottom of front panel. • h To remove front p...

Page 34 - Drum Drive Motor

Disassembly Disassembly -- -- Drum Drive Motor Drum Drive Motor 34 1st Edition/Revision 5 (1/20/04)

Page 35 - Drain Pump; ...and that’s all

Disassembly Disassembly -- -- Drain Pump Drain Pump 35 …and that’s all there is to taking apart the washers! 1st Edition/Revision 5 (1/20/04)

Page 41 - Two concrete vibration dampeners, top & front

41 WFL 2060 & WFR 2460 Service Tips WFL 2060 & WFR 2460 Service Tips -- -- Ratings Ratings • Rated 240VAC, 15A, 60 Hz (uses 11A max.). • Hot & cold water inputs, 3/4” NPT • Two concrete vibration dampeners, top & front • Uses NEMA 6-15P 240V, 15A, 3-wire plug • Spin speeds 600-1000 R...

Page 42 - Replacement; Switch S1

WFL 2060 Service Tips WFL 2060 Service Tips -- -- Configuring Configuring Replacement Control Modules Replacement Control Modules 42 Replacement WFL 2060 control modules (# 481304 ) aren’t configured. Please follow these instructions to set on-board switches to configure replacement modules. CAUTION...

Page 43 - Sample Displays

WFR 2460 Service Tips WFR 2460 Service Tips -- -- Configuring Configuring Replacement Control Modules Replacement Control Modules 43 NOTE: Note original equipment washer modules are factory configured and CANNOT be changed in the field. 4 2010011 T5: Variant Max. spin speed 2! 1000 RPM 3! 1100 RPM 4...

Page 45 - 0 Hz

WFL 2060 & WFR 2460 Service Tips WFL 2060 & WFR 2460 Service Tips - - - - Drain Pump Drain Pump 45 80 - 94 Ω 1.0 m 60 Hz 1st Edition/Revision 5 (1/20/04)

Page 50 - POLINOX TUB; Lifecycle Test

WFR 2460 Service Tips WFR 2460 Service Tips -- -- Polinox Polinox Outer Outer Drum (Tub) Drum (Tub) 50 POLINOX TUB POLINOX TUB Lifecycle Test 2,500 washes = 10 yearsHighest spin 300 consecutive times (wash-spin, wash-spin, etc. -have tested up to 900 wash-spin cycles) Heat Resistant Up to 130°C (266...

Page 51 - red; Low Spin Speeds

If the WFR 2460 control doesn’t allow spin speeds > 800 RPM, then the Reduced Ironing setting has been turned on. HINT: To exit the Reduced Ironing mode: L When Start/Pause indicating light flashes red , press Menu button until Reduced Ironing screen appears. L Press Select button until Reduced I...

Page 52 - To enter component test program for WFL 2060 washers

WFL 2060 Service Tips WFL 2060 Service Tips -- -- Test Program (1) Test Program (1) 52 The WFL 2060UC washers have test programs enabling the washers to self-diagnose problems, including listing the last fault code. To enter component test program for WFL 2060 washers ( to test individual parts or c...

Page 53 - Test parts individually as follows

WFL 2060 Service Tips WFL 2060 Service Tips -- -- Test Program (2) Test Program (2) 53 Test parts individually as follows : ♦ Motor – To start test, rotate cycle selector knob to Regular/Cotton Hot ( not through Off position ), then push Start button. To end test, rotate cycle selector knob out of R...

Page 54 - To enter comprehensive test program for WFL 2060 washers

WFL 2060 Service Tips WFL 2060 Service Tips -- -- Test Program (3) Test Program (3) 54 To enter comprehensive test program for WFL 2060 washers ( to test entire washer or check last wash fault): ♦ Rotate cycle selector knob to Off position and rotate spin speed knob to 1000 RPM. ♦ Push and hold Star...

Page 69 - WARNING; ! Unplug washer before making any resistance measurements.

WFL 2060 Service Tips WFL 2060 Service Tips -- -- Resistance Resistance Measurements from Control Module (1) Measurements from Control Module (1) 69 1st Edition/Revision 5 (1/20/04) Top Top 1 1 Disconnect & measure white 5-pin connector (with 3 black wires) to measure dual cold water valve. Valv...

Page 72 - ! Unplug washer before

WFR 2460 Service Tips WFR 2460 Service Tips -- -- Resistance Resistance Measurements from Control Module (2) Measurements from Control Module (2) 72 1st Edition/Revision 5 (1/20/04) WARNING ! Unplug washer before making any resistance measurements. 1 1 Disconnect & measure white 5-pin connector ...

Page 73 - Unplug washer before starting any repairs.

WFL 2060 & WFR 2460 Service Tips WFL 2060 & WFR 2460 Service Tips - - - - Troubleshooting (1) Troubleshooting (1) 73 Symptom Problem Solution Washer won’t start. Electricity is disconnectedor has been turned off. Cycle selector knob orcontrol module has failed. Make sure washer is conn...