Page 2 - SC & SI Remote Interface Description; Table of Contents
SC & SI Remote Interface Description en | 2 Bosch Security Systems B.V. | 2003 December | SC & SI Remote Interface Description Table of Contents 1 Introduction .......................................................................................................................................
Page 3 - Introduction; Definitions, Acronyms and Abbreviations
SC & SI Remote Interface Description en | 3 Bosch Security Systems B.V. | 2003 December | SC & SI Remote Interface Description 1 Introduction 1.1 Purpose The purpose of this document is to describe the remote interface for system configuration and system installation. The document specifies ...
Page 4 - System configuration and system installation; Remote System Configuration and System Installation
SC & SI Remote Interface Description en | 4 Bosch Security Systems B.V. | 2003 December | SC & SI Remote Interface Description 2 System configuration and system installation 2.1 Introduction The System Configuration and System Installation Remote Interface is part of the DCN software which a...
Page 6 - System; Remote function item explanation
SC & SI Remote Interface Description en | 6 Bosch Security Systems B.V. | 2003 December | SC & SI Remote Interface Description 3 System Configuration Functions 3.1 Introduction The system configuration functions described in this section are needed to query the set-up of the DCN-system from ...
Page 10 - Note; that future unit extensions of the DCN system can
SC & SI Remote Interface Description en | 10 Bosch Security Systems B.V. | 2003 December | SC & SI Remote Interface Description • DCNC_UNIT_CHAIRMAN • DCNC_UNIT_DELEGATE_CARD • DCNC_UNIT_INTERPRETER • DCNC_UNIT_DUAL_MIC • DCNC_UNIT_PC • DCNC_UNIT_DATA_COMM • DCNC_UNIT_CCU_CONTROL • DCNC_UNIT...
Page 15 - System; Update Notification item explanation; Each description consists of the following items:; Unit/user event relations; Single CCU System
SC & SI Remote Interface Description en | 15 Bosch Security Systems B.V. | 2003 December | SC & SI Remote Interface Description 4 System Configuration notifications 4.1 Introduction This chapter defines the set of update notifications concerning SC send by the CCU. 4.1.1 Update Notification ...
Page 16 - Event; Remote Controller connected to the Master CCU
SC & SI Remote Interface Description en | 16 Bosch Security Systems B.V. | 2003 December | SC & SI Remote Interface Description Single-Multi System , i.e. a Multi CCU system but one or more of the Slave CCU’s configured to run in Single Mode Event Update Notification Continue with remote fun...
Page 17 - bySlaveId
SC & SI Remote Interface Description en | 17 Bosch Security Systems B.V. | 2003 December | SC & SI Remote Interface Description 4.2 SC_C_CCU_REBOOT Purpose Notifies the remote controller that the CCU has restarted. This notification is always send at start-up of the CCU and is the only notif...
Page 18 - does; Purpose
SC & SI Remote Interface Description en | 18 Bosch Security Systems B.V. | 2003 December | SC & SI Remote Interface Description 4.6 SC_C_DISCONNECT_SLAVE_CCU Purpose Notifies the remote controller that the master-CCU has lost connection to one of his slave-CCU’s. Along with this notification...
Page 19 - System; Mode; This function is available in CCU system mode congress.; wInstallMode
SC & SI Remote Interface Description en | 19 Bosch Security Systems B.V. | 2003 December | SC & SI Remote Interface Description 5 System Installation Functions 5.1 Introduction The system installation functions provide functionality to connect unit identification with the seat numbers used w...
Page 20 - wUnitId
SC & SI Remote Interface Description en | 20 Bosch Security Systems B.V. | 2003 December | SC & SI Remote Interface Description Note that: Upon communication loss this function will be activated, if SI_C_START_INSTALL was activated. Availability This function is available in CCU system mode ...
Page 21 - wMasterVolume
SC & SI Remote Interface Description en | 21 Bosch Security Systems B.V. | 2003 December | SC & SI Remote Interface Description Error codes returned SI_E_NOERROR SI_E_FAILED SI_E_INVALID_UNITTYPE Related functions SI_C_START_INSTALL SI_C_STOP_INSTALL 5.5 SI_C_SET_MASTER_VOL Purpose To set th...
Page 22 - System; Installation not yet started
SC & SI Remote Interface Description en | 22 Bosch Security Systems B.V. | 2003 December | SC & SI Remote Interface Description 6 System Installation notifications 6.1 Introduction This chapter defines the set of update notifications concerning SI send by the CCU. Each description is accordi...
Page 23 - APPENDIX A. VALUES OF THE DEFINES
SC & SI Remote Interface Description en | 23 Bosch Security Systems B.V. | 2003 December | SC & SI Remote Interface Description APPENDIX A. VALUES OF THE DEFINES In this document a lot of definitions are given, which have values connected to them. In this appendix all defines will be connect...
Page 25 - APPENDIX B. ERROR CODES; The execution of the remote function was successful.
SC & SI Remote Interface Description en | 25 Bosch Security Systems B.V. | 2003 December | SC & SI Remote Interface Description APPENDIX B. ERROR CODES Responses returned upon a remote function request contain an error field (‘wError’). In this appendix an overview is given of the possible e...
Page 26 - Database Query Services Error code
SC & SI Remote Interface Description en | 26 Bosch Security Systems B.V. | 2003 December | SC & SI Remote Interface Description Database Query Services Error code Value Explanation The use of function SC_C_CCU_APPLY_ONE is not possible, because currently there is no database present in the C...
Page 27 - APPENDIX C. EXAMPLES; C.1. Assigning seats using global installation
SC & SI Remote Interface Description en | 27 Bosch Security Systems B.V. | 2003 December | SC & SI Remote Interface Description APPENDIX C. EXAMPLES In the examples below the remote functions and update notifications, that are defined in this document as constant values for the wFnId paramet...
Page 28 - C.2. Replacing defective units during operation; address conflict with other units.
SC & SI Remote Interface Description en | 28 Bosch Security Systems B.V. | 2003 December | SC & SI Remote Interface Description if (error != SI_E_NOERROR) { /* do error handling */ } This ends the global seat assignment. The remote controller has now a complete list of all seats and their co...
Page 30 - APPENDIX D. ERROR CODES; Remote Function Services Error code
SC & SI Remote Interface Description en | 30 Bosch Security Systems B.V. | 2003 December | SC & SI Remote Interface Description APPENDIX D. ERROR CODES Responses returned upon a remote function request contain a error field (‘wError’). In this appendix an overview is given of the possible er...
