Bosch DHI645NAU - User Manual

Page 3 - Operating modes; The complete installation set and; from; If no activated carbon filter is installed,; Description of appliance; If the extractor hood is operated in; which the heater requires for

16 Operating modes This can be achieved if the combustion airis able to flow through non-lockable openings, e.g. in doors, windows and inconjunction with an air supply/air-intake wallbox or by other technical procedures suchas reciprocal interlocking. If the air intake is inadequate, there is arisk ...

Page 4 - Before using for the first time; Repairs

17 Before using for the first time Important notes: ❑ The Instructions for Use apply to severalversions of this appliance. Accordingly,you may find descriptions of individualfeatures that do not apply to your specific appliance. ❑ This extractor hood complies with all relevant safety regulations. Re...

Page 5 - Operating the extractor hood; Cooking vapours are best eliminated; Switching on the extractor hood; when; Only switching off the extractor hood; Sliding switch to 0 – switch off fans.; To switch on the extractor again,; just; Faults

18 Operating the extractor hood Cooking vapours are best eliminated by: ❑ Switching on the extractor hood when you start cooking. ❑ Only switching off the extractor hood a few minutes after you have finishedcooking. Fan on / off Light on / off Intensive setting Fan settings Fan on / off Intensive se...

Page 6 - Saturation indicator:; Filters and maintenance; The halogen bulbs must be

19 4. Clean the filters. 5. Insert the clean filters back into the hood. 6. Cancel the in the display. ❑ Press the button. Grease filters: Metal-mesh filters are used to trap thegrease particles in the cooking vapours. The filter mats are made from non-combustible metal. Caution: As the filter becom...

Page 7 - Activated carbon filter:; Inserting the filter:

20 3. Engage the catches at both sides. 4. Insert the metal-mesh grease filters (see”Removing and inserting the metal-meshgrease filters”). Removing the filter: Warning: The halogen bulbs must be switched off and cool. 1. Remove the metal-mesh filters. 2. Depress the catches on both sides ofthe filt...

Page 8 - Cleaning and care; Stainless steel surfaces:; Replacing the light bulbs

21 Cleaning and care Isolate the extractor hood by pulling outthe mains plug or switching off the fuse. ❑ When cleaning the grease filters, removegrease deposits from accessible parts ofthe housing. This prevents the risk of fireand ensures that the extractor hoodcontinues operating at maximum effic...

Page 9 - The installation of the extractor hood

22 Important information Installation Instructions: The installation of the extractor hood above gas cooking devices, at a minimum height of 650 mm – Fig. 1 – is permitted provided that the following nominal heat loads (Hs) are not exceeded: ❑ Gas cookers Load of one hotplate max. 0 3.0 kW Load of a...

Page 10 - Prior to installation; Exhaust air must not be discharged via; For exhaust air mode; a telescopic wall box

23 Prior to installation Exhaust-air mode The exhaust air is discharged upwardsthrough a ventilation shaft or directlythrough the outside wall into the open. D Exhaust air must not be discharged via a smoke or exhaust gas flue which is already in use or via a shaft which is usedfor ventilating rooms...

Page 11 - Before installation; Exhaust air directed backwards:

24 Before installation Optimum efficiency of the extractorhood: ❑ Short, smooth exhaust pipe. ❑ As few bends as possible. ❑ Pipe diameter as large as possible (ideally 150 mm dia.) and wide pipebends. If long, rough exhaust-air pipes,many pipe bends or smaller pipe diameters are used, the air extrac...

Page 12 - Preparing the wall cupboard; This extractor hood

25 Preparing the wall cupboard This extractor hood is designed to be installed in a wall cupboard with the follo-wing dimensions: width: 600 mmdepth: 293 to 350 mmheight: min. 435 mm. If the cupboard is deeper than 293 mm, the extractor hood can be moved back,e.g. to put a spice rack in front of the...

Page 13 - Fitting into wall cupboard

26 3. Tighten the two fixing screws with a screwdriver (cordless). 4. If required, shorten the wall cover to therequired dimension (e.g. saw off).Attach the wall cover with the enclosedclips.Screw the wall cover to the wall cupboard. 5. Feed the mains connection cable out ofthe cupboard. 6. Connect ...

Page 14 - Exhaust air; Attaching the handle moulding:; Using the enclosed template

27 Fitting into wall cupboard ❑ If the extractor hood is to be installedfurther back in the cupboard, the stopsfor the filter drawer can be moved forwards. ❑ To do this, undo the screws, move thestops and retighten the screws. 2. Align handle moulding and screw to theappliance. Exhaust air Circulati...

Page 15 - Electrical connection; The extractor hood; Electrical specifications:; Before carrying out repairs,

28 Electrical connection WARNING: THIS APPLIANCE MUST BEEARTHED IMPORTANT: Fitting a Different Plug: The wires in the power cord are colour-coded as follows: Green and Yellow – Earth Blue – Neutral Brown – Live If you fit your own plug, the colours ofthese wires may not correspond with theidentifyin...

Page 16 - Notes

Page 19 - Robert Bosch Hausgeräte GmbH

5750 203 748 Printed in Germany 0704 Es. Robert Bosch Hausgeräte GmbH