Page 2 - Device overview
2 Device overview 12 13 14 15 16 3 2 10 1 4 11 5 6 7 8 9
Page 5 - Quick guide to navigation; LAST 1O; N1 NAVi
5 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Quick guide to navigation Press the NAV button 1 once to switch from the radio or CD-changer (optional)audio source to the main navigation menu. Use the menu knob : to select the DEST i- nation INP ut menu item and then press the OK ...
Page 6 - STRASSE; pm
INTRODUCTION NAVIGATION 6 RADIO CD / MP3 CD CHANGER SETUP APPENDIX In the subsequent selection, choose be-tween STREET , TOWN CENTR e or POI (point of interest). Streets can only be selected if the data areavailable on the navigation CD that is be-ing used. If you selected STREET , you can subse- qu...
Page 7 - Safety notices
7 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Safety notices The TravelPilot E1/E2 has been designed for use in passenger cars. Special information such as height restrictions or maximum permitted road load, which is required for navigatinglorries, trucks and buses, is not inclu...
Page 10 - Compatible navigation CD-ROMs; Care tips for CD-ROMs
INTRODUCTION NAVIGATION 10 RADIO CD / MP3 CD CHANGER SETUP APPENDIX Compatible navigation CD-ROMs The TravelPilot E1/E2 can only be used with navigation CD-ROMs that are la-belled with an “E”. If there is no CD-ROM inserted in the device, a messageinforming you of this appears in the display as soon...
Page 11 - About these instructions
11 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX About these instructions The aim of these instructions is to familiarize you with the functions of yourTravelPilot E1/E2 and to ensure that you can safely and successfully operatethe device. Before starting to use your TravelPilot E...
Page 13 - Attaching the release panel
13 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Attaching the release panel 1 Slide the control panel straight into the device’s bracket. 2 Close the control panel. Note: When attaching the control panel, make sure you do not pressthe display.
Page 14 - Switching the device on/off; Switching on/off using the vehicle ignition
INTRODUCTION NAVIGATION 14 RADIO CD / MP3 CD CHANGER SETUP APPENDIX Switching the device on/off 1 To switch on your TravelPilot E1/E2, press button 3 . ✔ The device plays the last active audio source at the volume level that wasset when the device was last switched off. You can limit the power-on vo...
Page 17 - Putting through telephone calls automatically; TELEPHONE; volume 8
17 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Putting through telephone calls automatically If the device is properly connected to a car telephone, telephone calls will beoutputted over the loudspeakers of the TravelPilot E1/E2. TELEPHONE appears in the display. The call will b...
Page 18 - Display
INTRODUCTION NAVIGATION 18 RADIO CD / MP3 CD CHANGER SETUP APPENDIX Display The TravelPilot E1/E2’s display contains all the navigation information (e.g. vis-ual driving recommendations), menus and lists, as well as the radio, CD andCD-changer (optional) audio sources. The display’s brightness and r...
Page 19 - CODE; O O O
19 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Switching on a coded device after disconnectionfrom the battery power supply If you switch on a coded device after having disconnected it from the batterypower supply (e.g. after carrying out repairs to the vehicle), the system will...
Page 20 - Entering the wrong numerical code; WRONG CODE
INTRODUCTION NAVIGATION 20 RADIO CD / MP3 CD CHANGER SETUP APPENDIX Once you have finished entering the whole numerical code and it is shown in thedisplay, 4 press and hold down the OK button ; for longer than 2 seconds. ✔ The device switches on. Entering the wrong numerical code If you inadvertentl...
Page 21 - Navigation; How navigation works
21 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Navigation The navigation system in the TravelPilot E1/E2 helps you find your way to des-tinations quickly and safely without first having to spend time studying a road-map. When navigation (route guidance) is active, you will be gu...
Page 22 - DOWNLOAD; NAVI SW
22 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Note: If you do not take out the ejected CD, the drive will draw itback in again automatically after approx. 10 seconds. Downloading the navigation software The system automatically loads the navigation software into memory from the...
Page 23 - Starting navigation
23 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Note: Any memory available after the corridor has been loaded willbe used to store the data for the surrounding area function. The CDsymbol at the bottom right of the display indicates when data arebeing loaded. Data are loaded even...
Page 24 - Entering a destination; N2 NAVi
24 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX To switch between the navigation system’s memory banks, 1 press the NAV button 1 repeatedly until the memory bank that you want appears in the top line of the display. Before navigation can begin, you must first insert a TravelPilot...
Page 25 - Entering destinations using the text input line; YORCKGEBIE; BERL
25 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Entering destinations using the text input line You can use the text input line to enter data such as town names and roadnames into the navigation system. The text input line is equipped with an intelli-gent text-input feature, whic...
Page 27 - Entering a destination – Country; Entering a destination – Town; DEUTSCHLAN
27 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Entering a destination – Country The navigation CD currently contains the entire road data for a country as wellas the interconnecting road network (Major Roads) for Europe. When you entera destination for the first time, the system...
Page 29 - HOSPITAL
29 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Note: If there are several instances of the place name that you se-lected, the system will display another menu containing the text in-put line so that you can define the county. Enter some more lettersin order to define the place m...
Page 30 - STREET; HOUSE NUMB; UNTER DEN
30 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX 3 Enter the special destination name in the same way as you would enter adestination name. 4 Switch to the list. ✔ The available special destinations are displayed alphabetically. 5 Mark and confirm the destination that you want. As...
Page 32 - Entering a destination – Centre; POI; CHARLOTTEN
32 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Crossroads If you selected the JUNCTION menu item, a list of road junctions and crossroads that are available on the destination street will be displayed. Note: If a crossroads or junction appears twice, the system will alsodisplay ...
Page 33 - Entering a destination – Special destinations
33 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX 3 You can now start navigation using the OK button ; . Plus Point: After you have finished entering the destination and before start-ing navigation, you have the option of storing the destination in the destina-tion memory. For furt...
Page 34 - EXHIBITION; AIRPORT
34 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX ✔ The destination input menu appears. 3 Select and confirm the SUPRAREG ional D estinations menu item. ✔ A list of special destinations categories is displayed. 4 Select and confirm the category that you want. ✔ The available destin...
Page 36 - Entering a destination – Last 10 destinations
36 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Note: If available, the text input line is opened first of all. Use it toenter the required name or the first letter and then open the list. 5 Select and confirm the destination that you want. As soon as you have selected and confir...
Page 37 - Entering a destination – From the destination memory
37 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Entering a destination – From the destination memory You can store destinations in the destination memory that you drive to regularlyso you can access them easily for other navigation sessions. For further infor-mation, read the sec...
Page 38 - Destination memory
38 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Destination memory In the destination memory you can store destinations that you want to navigateto later on. You can also set your current position as a position marker and thenaccess it from memory at some other point in time to u...
Page 39 - TZENWIESE
39 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX ✔ You will hear a confirmation beep when the destination has been stored.The navigation display will then appear again. Storing your current position as a destination You have the option of storing your vehicle’s current position as...
Page 41 - HNELLWEG
41 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Plus Point: If you deviate from the recommended route, the system automat-ically calculates a new route from the current vehicle position to the alreadyentered destination. The system might ask you to insert the navigation CD. Drivi...
Page 42 - CANCEL; NAVI
42 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Switching audio sources You can switch to a different audio source at any time during navigation. 1 Press the FM•AM 4 button or the CD•C button 5 during the active naviga- tion session to switch between radio mode and CD-changer mod...
Page 43 - Dynamic navigation; DYNAMIC
43 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX TRAFF. JAM ROUTE OPTI NAVI NAV TMC TMC B6, WESTSC HNELLWEG FM1 NDR 2 NAV 16mi 10 16 pm Dynamic navigation During dynamic navigation, the TravelPilot E1/E2 analyses digital traffic infor-mation messages and uses this information when...
Page 45 - TMC AUTO; radio; ON
45 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX 3 Mark and confirm the TMC AUTO menu item. 4 Mark the ON menu item and press the OK button ; . 5 Press the ESC button = twice to return to navigation mode. Tuning into TMC stations manually To tune into a TMC station manually, proce...
Page 46 - Bypassing a traffic jam during navigation; DISTANCE
46 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Bypassing a traffic jam during navigation Alongside the ability to automatically bypass traffic jams with the aid of the dy-namic navigation feature, the TravelPilot E1/E2 also gives you the option ofmanually entering traffic jams o...
Page 47 - Defining route options
47 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Defining route options You can customise the route to suit your requirements at any time, even duringan active navigation session. The configurable parameters are: ● DYNAMIC : Dynamic navigation with TMC. ● FAST : The system calcula...
Page 48 - FREEWAY
48 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX To define the route options, 1 press and hold down the NAV button 1 for longer than 2 seconds. ✔ A selection menu appears in the display. 2 Mark and confirm the ROUTE OPTI ions menu item. ✔ The menu for setting the route options app...
Page 49 - Displaying the route list
49 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX B6, WESTSC HNELLWEG FM1 NDR 2 NAV TMC 16mi 10 16 pm Displaying the route list You can display the route list that was calculated by the navigation system. Theroute list is updated during the journey, and the route sections that you ...
Page 50 - Radio mode; RDS; rdS
50 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Radio mode The TravelPilot E1/E2 is equipped with an RDS radio receiver. Many of thereceivable FM stations transmit a signal that not only carries the programme butalso additional information such as the station name. The station na...
Page 51 - regional
51 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX 5 Press the OK button ; or the ESC button = to accept the setting. ✔ The selection menu appears again. 6 Press the ESC button = twice to close the selection menu. Switching the REG RDS function on or off 1 Press the MENU button ? . ...
Page 52 - FMT; MEMORX BANK
52 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Switching to radio mode To switch to radio mode, 1 briefly press the FM•AM button 4 . ✔ The radio will play the station that it received last. Selecting the waveband / memory bank This device can receive programmes broadcast over th...
Page 53 - Tuning into a station
53 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Tuning into a station There are various ways of tuning into a station. Automatic station seek tuning 1 Press the button 7 or the button 8 . ✔ The radio tunes into the next receivable station. Note: You can adjust the sensitivity of ...
Page 54 - Storing stations; Listening to stored stations
54 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Storing stations Storing stations manually 1 Select the memory bank (i.e. FM1, FM2, FMT) that you want or one of thewavebands (MW or LW). 2 Tune into the station that you want. 3 Press and hold down one of the station buttons 1 - 6 ...
Page 55 - Traffic information; FM1 SCAN
55 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Scanning receivable stations (SCAN) You can briefly play (scan) all the receivable stations. The scanning time is 10seconds. Starting SCAN 1 Press and hold down the OK button ; for longer than 2 seconds. ✔ Scanning begins. SCAN appe...
Page 57 - CD mode; Playing a CD; TRACK 7; CD
57 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX CD mode You can play standard audio CDs with a diameter of 12 cm in the TravelPilot E1/E2’s internal CD drive. CD-Rs (CDs that you have “burned” yourself) can generally also be played. Dueto the varying quality of CDs, Blaupunkt can...
Page 59 - TRACK 2; mix CD
59 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX If you want to activate the internal CD drive, 1 press the CD•C button 5 again. ✔ The CD starts playing. Selecting tracks You can select tracks directly whilst a CD is playing. To select the next track, 1 press the button 8 . ✔ If t...
Page 60 - Traffic announcements during CD mode; TRACK 6; scan CD
60 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX To cancel the MIX function, 1 press the 2 MIX station button > again. The MIX function is automatically cancelled if you activate the SCAN function. Scanning all the tracks on a CD (SCAN) If you briefly want to play (scan) all th...
Page 63 - Boy Sets; MP3
63 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Switching to MP3 mode MP3 mode is activated in the same way as normal CD mode. For further infor-mation, please read the section entitled “Playing a CD” in the “CD mode” chap-ter. Once the device has checked the CD, it begins playin...
Page 64 - O2 Rookie; MP3 BROWSER; Fashion N; MP3 BROWSER
64 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Selecting a directory in browse mode You can display the current directory and the three subsequent directories onthe four lines of the display. The directories are displayed with the names thatyou created when burning the CD. In th...
Page 65 - Selecting tracks; O1 After
65 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Selecting tracks Selecting tracks/files using the arrow buttons To move up to another track/file in the current directory, 1 press the button 8 once or several times. To move down to another track/file in the current directory, 1 pr...
Page 66 - Fast seeking
66 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Fast seeking To start fast forward seeking, 1 press and hold down the button 8 until fast seeking begins. To start fast reverse seeking, 1 press and hold down the button 7 until fast seeking begins. Random play (MIX) You can play al...
Page 67 - Scanning all the tracks in a directory (SCAN)
67 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Scanning all the tracks in a directory (SCAN) If you briefly want to play (scan) all the tracks in the current directory, proceedas follows: 1 Press and hold down the OK button ; for longer than 2 seconds. ✔ All the tracks in the di...
Page 68 - Selecting MP3 info; FIX; MP3 NAME; SOUND
68 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Selecting MP3 info Whilst MP3 mode is activated, the track name appears as scrolling text on thefirst line of the display and the name of the artist appears on the second andthird lines (only if the ID tags are available in the MP3 ...
Page 69 - Switching to CD-changer mode
69 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX CD-changer mode You can use the following Blaupunkt CD changers with the TravelPilot E1/E2: ● CDC - A03 ● CDC - A08 ● IDC - A09 Please refer to the installation and connection instructions supplied with yourCD changer for informatio...
Page 70 - Selecting CDs; CDC DISC; CD O1; CDC
70 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX If the audio CD in the internal CD player is active, then 2 press the CD•C button 5 again. ✔ The CD changer display appears. CDC appears in the top line of the display.Beneath it you will see the number of the CD in the CD changer, ...
Page 71 - CD O2
71 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Selecting tracks To select the next track, 1 press the button 8 . ✔ If the last track on the CD has been reached and you press the button 8 , the system will then switch to the first track. To replay the current track or select a pr...
Page 72 - MAG scan; mix magAZINE
72 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Randomly playing all the tracks on all the CDs To play the tracks on all the CDs at random, 1 press the 2 MIX station button > repeatedly until MIX MAGAZINE appears in the top line of the display. ✔ The tracks on all the CDs in t...
Page 73 - Traffic announcements during CD-changer mode
73 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Repeating tracks (REPEAT) To repeat a track, activate the repeat function. 1 Select the track that you want, 2 press the 5 RPT station button > . ✔ The track is repeated until you cancel the repeat function. If you want to cancel...
Page 74 - Steering wheel remote control; Selecting an audio source
74 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Steering wheel remote control The RC 10 steering wheel remote control allows you to safely and convenientlyoperate some of the TravelPilot E1/E2’s primary functions from your steeringwheel. The / buttons have the same function as th...
Page 75 - Muting
75 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Muting You can mute the device’s volume using the remote control. 1 Press the button. Cancelling mute If you want to cancel mute, 1 press the button again or 1 press the V+ or V- button. REMOTE CONTROL
Page 76 - Setup – basic settings; Adjusting the sound and sound distribution settings
76 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Setup – basic settings The setup menu allows you to adjust the TravelPilot E1/E2’s basic functions tosuit your needs. You can change the following device functions: ● SOUND - Adjust the sound distribution and equalizer ● VOLUME - Se...
Page 77 - Equalizer; BASS; bass
77 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX 2 Press the MENU button ? . ✔ The setup menu appears in the display. 3 Mark and confirm the SOUND menu item. ✔ The sound menu appears in the display. 4 Mark and confirm the menu item ( BASS , TREBLE , LOUDNESS , BALANCE or FADER ) w...
Page 79 - DIGITAL EQ; frequenCX; FREQUENCY; SUB LOW EQ; SUB LOW
79 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Adjusting the equalizer 1 Press the MENU button ? . ✔ The setup menu appears in the display. 2 Mark and confirm the SOUND menu item. ✔ The sound menu appears in the display. 3 Mark and confirm the DIGITAL EQ menu item. ✔ The equaliz...
Page 81 - Configuring the radio functions; VOLUME; ON MAX
81 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX ✔ The volume menu appears in the display. 3 Mark and confirm the menu item whose setting you want to change. ✔ The scale for adjusting the setting is displayed. 4 Set the volume level that you want using the menu knob : . ✔ To help ...
Page 83 - Setting the day/night display brightness and contrast; DisplaX; DISPLAY
83 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX 3 Mark and confirm the menu item that you want to adjust. ✔ The selection menu or the scale for adjusting the setting is displayed. 4 Select the setting using the menu knob : . 5 Press the OK button ; or the ESC button = to accept t...
Page 84 - Configuring the language and speech options; DimmIng
84 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX 4 Adjust the value that you want using the menu knob : . 5 Press the OK button ; or the ESC button = to accept the setting. ✔ The display menu appears in the display again. 6 Press the ESC button = twice to close the display menu. C...
Page 85 - SPEECH OUT
85 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Setting the language To set the language, 1 press the MENU button ? . ✔ The setup menu appears in the display. 2 Mark and confirm the LANGUAGE menu item. ✔ The available languages are displayed alphabetically. 3 Mark and confirm the...
Page 87 - Configuring the optimum route (only TravelPilot E2); OPT ROUTE
87 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Configuring the optimum route (only TravelPilot E2) The TravelPilot E2 allows you to configure the optimum route yourself. To do so,you must adjust the relationship between “fast route” and “short route”. Thefactory default setting ...
Page 88 - Adjusting the clock; CLOCK
88 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Adjusting the clock The system normally sets the clock using the GPS signal. You will only have toset the current local time to the nearest five minutes once. Note: You can also set the local time here when switching from sum-mer to...
Page 89 - Device code
89 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Device code If you switch on a code-enabled device after it was disconnected from the vehi-cle’s power supply, you will have to enter the device code. You can also disablethis code request feature. Activating / deactivating the code...
Page 90 - Installation; Installation test; AUTO CALIB; REVERSE
90 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Installation The installation menu contains all the necessary items for testing the TravelPilotE1/E2 and preparing it for operation. Installation test The installation test allows you to check whether the system is correctly receiv-...
Page 91 - Automatic device calibration
91 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX ● IGNIT ion - Positive ignition connection Switch on the ignition. ON appears alongside IGNIT ion. ● SPEED - Speedometer connection Move the vehicle a short distance. If the system detects the presence of thespeedometer signal it st...
Page 92 - Manual device calibration; MANUAL Calib
92 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Manual device calibration You can also manually calibrate the device. You will be required to drive a routeof at least 110 yards (100 metres) to 550 yards (500 metres) at a maximumspeed of 18 mph (30 km/h). Please note that you must...
Page 93 - Glossary
93 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Glossary Corridor function The corridor function allows the TravelPilot E1/E2 to provide driv-ing instructions even when the navigation CD is not present inthe drive. This applies to normal navigation as well as to dynamicnavigation...
Page 94 - Specifications; Voltage supply; Amplifier
94 INTRODUCTION NAVIGATION RADIO CD / MP3 CD CHANGER SETUP APPENDIX Specifications Voltage supply Operating voltage: 10.8 - 14.4 V Current consumption: max. 10 A Power consumption for30 minutes after switching off: 550 mA typical Standby current consumption: 12 mA Standby current consumptionafter 72...
Page 95 - Blaupunkt GmbH
Country: Phone: Fax: www: Germany (D) 0180-5000225 05121-49 4002 http://www.blaupunkt.com Austria (A) 01-610 39 0 01-610 39 391 Belgium (B) 02-525 5444 02-525 5263 Denmark (DK) 44 898 360 44-898 644 Finland (FIN) 09-435 991 09-435 99236 France (F) 01-4010 7007 01-4010 7320 Great Britain (GB) 01-8958...
