Barco RS905948/00 - Manual

1. Introduction 1.1 About this guide This manual This User’s guide describes how to install and operate the E2 Screen Management system. The User’s Guide is designed to be areference tool in the everyday work of the user with the product. It contains a complete description of the hardware components...

1. Introduction 1.2 Symbols, pictures and fonts Symbol overview The following icons are used in the manual : Caution Warning Info, term de fi nition. General info about the term Note: gives extra information about the described subject Tip: gives extra advice about the described subject Picture over...

1. Introduction 1.3 The 4K screen management system E2 The E2 presentation system Raising the bar for live screen management, the E2 presentation system provides superior image quality, exceptional input andoutput density, great expandability and durability. Supporting native 4K input and output, it...

2. Safety 2.1 General considerations General safety instructions • Before operating this equipment please read this manual thoroughly and retain it for future reference. • All warnings in the documentation manual should be adhered to. • All instructions for operating and use of this equipment must b...

2. Safety 2.2 Important safety instructions To prevent risk, personal injury and E2 damage Please read this chapter carefully. It includes several cautions to prevent damage to the E2. Ensure that you understand and followall safety guidelines, safety instructions and warnings mentioned in this chap...

3. General 3.1 E2 overview About E2 E2 is a is modular scalable Digital Video Processor dedicated to the live screen management. The E2 presentation system providessuperior image quality and an exceptional input and output density, within a single 4RU rack mount chassis. Supporting native 4KI/O card...

3. General 3.2 Features Inputs 8x Input card slots supporting up to 4K resolution per slot. Each card slot will accommodate either 4x HD inputs, 2x 2,560 x 1,600 inputs, or 1x 4K input. Card type Connector Type HDMI/DisplayPort input card 2x HDMI 1.4 connectors 2x DisplayPort 1.1 connectors Dual Lin...

3. General Chassis • 4RU • Dual Redundant PSU • Modular fi eld swappable processing and I/O cards • Variable fl ow cooling • Rugged steel chassis R5905948 E2 12/12/2014 17

3. General 3.3 Terms and de fi nitions 3G A 3 Gbit/s serial digital 10-bit or 12-bit video interface (SMPTE 424M and 425M). Background (BCK) Typically an unscaled source originating from a computer’s multi-head graphics card, or a frame grab from a scaled source. E2provides two background sources ( ...

3. General 3.4 Control overview General There are four ways to control the E2:• Front Panel • Event Master Control Software (EM GUI) running on Windows 7 PC or Mac with OS X • Web interface running from E2 • E2 Controller * (*) Available in 2015 Front Panel The E2 front panel includes a power switch...

3. General 3.5 Presentation System overview Advanced video processing The E2 Presentation System is the most advanced video processing and presentation control system on the market today. The sys-tem provides source selection, windowing, seamless switching, video effects and integrated control for p...

3. General 3.6 Installation requirements Environment conditions Table below summarizes the physical environment in which the E2 may be safely operated or stored. Environment Operating Non-Operating Ambient Temperature 0°C (32°F) to 40°C (104°F) -10°C (14°F) to 60°C (140°F) Air cleanliness Clean of f...

3. General 3.7 Initial inspection General Before shipment, the E2 was inspected and found to be free of mechanical and electrical defects. As soon as the E2 is unpacked,inspect for any damage that may have occurred in transit. Save all packing material until the inspection is completed. If damage is...

3. General 3.8 E2 Rack-Mount Procedure General The E2 chassis is designed to be rack mounted and is supplied with front rackmount hardware. Please note the following importantpoints:• The E2 is 4RU in height. • The maximum ambient operating temperature is 40 degrees C. • Leave suf fi cient front and...

4. Hardware orientation 4. HARDWARE ORIENTATION About this chapter This chapter explains the E2 hardware in detail. Overview • Front panel • Rear panel • 6G SDI Input Card • Dual Link DVI Input Card • HDMI/DisplayPort Input Card • HDMI Output Card • 6G SDI Output Card • Expansion link card R5905948 ...

4. Hardware orientation 4.1 Front panel About front panel The fi gure below illustrates the E2 front panel. Image 4-1 1 Chassis Handles 2 Barco logo 3 Display screen 4 Menu navigation buttons 5 Power ON/OFF button 6 USB port Chassis Handles Two Chassis Handles are provided for ease of installation a...

4. Hardware orientation • Turn the ADJUST knob to scroll through the menu items on the screen.- Turn the knob counter-clockwise to scroll down. - Turn the knob clockwise to scroll up. A navigation cursor (>) to the left of a menu item indicates the position of the scroll bar, as shown in thefollo...

4. Hardware orientation 4.2 Rear panel About rear panel The fi gure below illustrates the E2 rear panel. Image 4-4 1 Two AC connectors 2 RJ-45 connector for 10/100 BaseT Ethernet communications 3 Two Genlock Input BNC with passive Loop-through 4 Two Expansion link cards 5 Eight Input cards (HDMI/DP,...

4. Hardware orientation The Ethernet connector is compatible with:• Standard RJ-45 Ethernet cables • Neutrik EtherCon® series cables For pinout details, refer to the section dedicated to the pinout in Appendix A, "Standard connector pinouts", page 288. Genlock Input BNC (with passive Loop-th...

4. Hardware orientation 4.3 6G SDI Input Card General This card provides 4 BNC connectors supporting Single Link, Dual Link and Quad Link signals, in SD, HD, 3G-SDI and 6G-SDI UltraHD (UHD) formats. Currently the supported formats are up-to 3G SDI. 6G SDI format will be provided with a future softwa...

4. Hardware orientation 4.4 Dual Link DVI Input Card General The Dual Link DVI input card includes two DVI-I dual-link connectors which can support a single or dual-link DVI video signal. Although the DVI-I connectors includes pins that support analog signals, the DVI card doesn’t support analogsign...

4. Hardware orientation Speci fi cations • DVI 1.0 Speci fi cation • Maximum H Active: 4,096, Maximum V Active: 3,072 • Supported format:- All single link DVI formats up to 165 MHz - All dual link DVI formats up to 330 MHz - 4K/UHD Supported: o 3,840x2,160/ 23.98/24/25/29.97/30 input via 1x DVIDL, 2...

4. Hardware orientation 4.5 HDMI/DisplayPort Input Card General The HDMI/DisplayPort Input Card has two 19–pin HDMI connectors which can support a HDMI video signal, and two 20–pin Dis-playport connectors supporting DisplayPort video signal. The fi gure below illustrates the HDMI/DisplayPort input c...

4. Hardware orientation DisplayPort speci fi cations • DisplayPort per 1.1a speci fi cations • Supported format:- formats up to 2,560x1,600@60 and 3,840x1,200@60 (30 bits) - 4K/UHD Supported: o 3,840x2,160/ 23.98/24/25/29.97/30 via 1x DP, 2x DP (L and R half) or 4x DP (quadrants) o 3,840x2,160/ 50/5...

4. Hardware orientation 4.6 HDMI Output Card General The HDMI Output Card has four 19–pin HDMI connectors which can provide a HDMI video signal. The fi gure below illustrates the HDMI output card’s rear panel connectors: Image 4-8HDMI Output Card Rear Panel 1 HDMI connector — HDMI 1 2 HDMI connector...

4. Hardware orientation 4.7 6G SDI Output Card General The 6G SDI Output Card has 4 BNC connectors which can support Single Link, Dual Link and Quad Link signals, in SD, HD, 3G-SDIand 6G-SDI Ultra HD (UHD) formats. The fi gure below illustrates the 6G SDI Output Card’s rear panel connectors: Image 4...

4. Hardware orientation 4.8 Expansion link card About Expansion link When is necessary to expand beyond the capabilities of a single E2 unit multiple E2s can be connected together vial the link card. CXP CXP is a copper connector system speci fi ed by the In fi niBand Trade Association. It provides ...

5. Front Panel Menu orientation 5. FRONT PANEL MENU ORIENTATION About this chapter This chapter describes E2 front panel menus, including how they are accessed and the functions or parameters that are available.The menu trees are presented in block diagram format throughout the chapter. Overview • P...

5. Front Panel Menu orientation 5.1 Power-up initialization Initialization Ensure that your system is properly installed and cabled. Make sure the two AC Connector are properly connected to your facility’sAC power source through the two supplied power cords. Locate the power button on the front pane...

5. Front Panel Menu orientation 5.2 E2 Front Panel menu tree About this section The diagram below illustrates the E2 Front Panel menu tree. Please use this diagram for reference as you learn how to operate thesystem. Menu tree Image 5-2 R5905948 E2 12/12/2014 47

5. Front Panel Menu orientation 5.3 Using menu system General This section describes the conventions for using the E2’s menu system. For reference, the following illustration shows the System Menu. Image 5-3System menu The E2’s display screen is four lines high. Throughout this chapter, entire menus...

5. Front Panel Menu orientation Answering a menu query The SEL button is used to answer Yes to certain menu queries. The ESC button is used to answer No to menu queries. Sometimes the two buttons are appropriate for answer to a menu queries. The following illustration shows an example of a menu quer...

5. Front Panel Menu orientation 5.4 About Status menu General The Status Menu is the E2’s top-level menu, which appears by default at system startup. This menu provides system name, Unit ID, Genlock status and E2 IP address. The following fi gure illustrates a sample Status Menu. Press the ESC butto...

5. Front Panel Menu orientation 5.5 About Setup menu General The Setup menu, shown in the following illustration, is the menu from which you access all operational menus. To display the Setup menu, press the SEL button on the front panel when the Status menu is displayed, or press the ESC button to ...

5. Front Panel Menu orientation 5.6 About the System menu General The System Menu, shown in the following illustration, allows you to view and change settings such as HDCP status and Ethernet options. In this menu you can also backup or restore E2 con fi guration, obtain diagnostic information, adju...

5. Front Panel Menu orientation 5.7 System menu > Black Invalid General The Black Invalid system setting determines whether the output is black when connected to a signal it cannot process. Black Invalid is either On or Off . The default setting is On . This is a global setting, applicable to all...

5. Front Panel Menu orientation 5.9 System menu > Ethernet General The Ethernet submenu allows the user to view and change certain Ethernet settings. Image 5-13 Using this menu, you can:• Query the DHCP server for a valid IP address, or turn off this feature. • Set a static IP address for the E2,...

5. Front Panel Menu orientation If you press ESC at any time before accepting your fi nal change, all your edits will be removed, and the original values restored. R5905948 E2 12/12/2014 57

5. Front Panel Menu orientation 5.10 System menu > VFD brightness (display brightness) General The VFD Brightness submenu adjust the intensity of the front panel vacuum fl uorescent display (VFD) screen. The adjustment range is +0 to +6 , with +6 being the brightest. The default setting is +3 . 5...

5. Front Panel Menu orientation Cards Image 5-17 The Card Slot test will perform a variety of diagnostics for an individual card or for all cards. This is a quick way to determine if a givencard is having a problem. After selecting a Slot number or choosing All cards to be tested, the following mess...

5. Front Panel Menu orientation To see more detailed results of diagnostic testing, run diagnostics from the Event Master Control Software.For details on this fonction, please refer to chapter "Settings Menu > WebKit area > Dashboard", page 145 Temperature Image 5-22 The DIAGNOSTIC TEM...

5. Front Panel Menu orientation 5.13 Using the Tech Support menu General The Tech Support Menu, shown in the following illustration, provides quick access to Customer Support contact information, and also shows you the software version for your E2. Image 5-26Tech Support Menu This menu displays:• Th...

5. Front Panel Menu orientation 5.14 Restoring Factory Default Settings General As shown in the following illustration, two options in the Setup Menu allow you to restore the E2 to its factory default condition. Image 5-27 The following attributes constitute a factory default condition:• The Status ...

5. Front Panel Menu orientation 5.15 Firmware Upgrade General The E2 provides two options for upgrading fi rmware: • Using the USB port on the front panel. • Using the Web Interface. Please refer to the chapter "Settings Menu", page 142 for the instructions on how to perform fi rmware upgrad...

5. Front Panel Menu orientation 5.16 Save All General Save All on the Setup menu saves your custom con fi guration parameters in non-volatile memory. If you save the system state, these parameters are restored the next time you power up the E2. If you do not use this function, yourcustom settings ar...

6. GUI orientation 6.1 General requirements System requirements for Microsoft Windows Minimum hardware speci fi cations : • PC Pentium IV or equivalent, 1 GHz or faster • 8 GB RAM • Free hard disk space: 600 MB • SXGA resolution (1280 x 1024) • Ethernet connection Software• Windows XP Professional, ...

6. GUI orientation 6.2 Download of Event Master Control Software Overview The Event Master Control Software can be downloaded for free from Barco’s website, (URL: http://www.barco.com ). The software is also available on myBarco and login to get access to secured information. Registration is necessa...

6. GUI orientation 6.3 Software installation Currently the EM GUI is available for PCs with Microsoft Win7 and Apple MACs with OS X. The software willrun on other Microsoft and Mac operating systems, but currently Barco only supports software installationswith Win7 and OS X computers. Linux version ...

6. GUI orientation 6.4 Starting up How to start up 1. Double click on the Event Master Control Software icon on your desktop Or,click Start → All programs → Barco → E2 → Event Master Control Software The software starts up with the same look and feel as when it was closed before. The connection is a...

6. GUI orientation 6.5 Screen layout presentation General The user interface is organized around a Menu Navigation bar at the left of the screen and a Working area in the rest of the screen. The layout of the screens is similar throughout the GUI. In order to explain the layout, we will examine the ...

6. GUI orientation 6.6 Controls General Edit box Edit box is used to edit the values or names. Image 6-2 Properties:• By double clicking, the background changes to a dark blue color indicating that modi fi cations can be made. • The cursor is placed on the last character. • The eraser button allows ...

6. GUI orientation 6.7 Con fi guration Menu General The Con fi guration menu is the module used to edit the Presentation Systems (creation, modi fi cation, deletion). This page is the fi rst page that appears when you launch the EM GUI software. The user will use this page to add or remove devices t...

6. GUI orientation 6.9 Con fi guration Menu > System diagram area General The system is represented graphically in this part of the System con fi guration page. It is here that the user can select a system (or create a new one), or select a system element (inputs, outputs, destinations …) Descrip...

6. GUI orientation 6.11 Con fi guration Menu > Adjustment area General Situated on the right hand side of the screen is the Adjustment area. In this area the user can de fi ne and adjust unit speci fi c param- eters, inputs, backgrounds, outputs and destination affected to the selected system. De...

6. GUI orientation 6.12 Con fi guration Menu > Adjustment > Unit Con fi guration General In the unit con fi guration adjustments panel, the user can de fi ne and adjust unit (device) speci fi c parameters. How to access to the unit con fi guration adjustments panel 1. Select the device (unit) ...

6. GUI orientation Image 6-18 The input adjustment panel is displayed. Input adjustment panel description The input adjustment panel is divided in four sections. • Main page • Format & Timing • Color Adjustment • Contact Information Input adjustment panel > Main page This menu is available in...

6. GUI orientation Or,clicking on the connector graphic. An output is selected. 2. Click on the Adjust tab that is on the top of the Adjustment area. Image 6-26 The output adjustment panel is displayed. Output adjustment panel description The output adjustment panel is divided in three sections • Ma...

6. GUI orientation Output adjustment panel > Main page • Auto Con fi gure Output format: Selects the output format will be set to match the format contained in the EDID of thedisplay device connected to the corresponding output(s). • Name: The name of the output con fi guration can be edited in t...

6. GUI orientation Output adjustment panel > Timing Menu • Format: Selects the video format of the output con fi guration from the drop menu. This is the same adjustment as in theprevious menu. • H Total: Adjusts (in pixels) the total pixel count per line forthe selected output. • H Front Porch: ...

6. GUI orientation Output adjustment panel > Connector Menu • SDI type (available with SDI connector type) : allows tochoose between Single link or Dual link connection ( Duallink: single image stream split between the two cables). • DVI Sync (available with HDMI connector type) : Adjuststhe sync...

6. GUI orientation 6.16 Con fi guration Menu > Adjustment > Destination Con fi guration General Output con fi guration that are created in the previous menus are assigned to destination in the Destination Panel. Description Destination con fi guration menu is accessed by clicking on the Destin...

6. GUI orientation It is possible that after the unit is turned on, the hardware con fi guration can be altered making certain Destinations to have invalid Output con fi gurations. In this case the Destination in the System Diagram becomes grey and adjustment are disabled. In this case the destinati...

6. GUI orientation Or,click in the “x” on the right hand side in the destination con fi guration list. Image 6-29 destination(s) is immediately outlined in red. 3. The deletion is completed by clicking the Delete Selected button. Any output can be deleted from a destination at any time. For example,...

6. GUI orientation Image 6-31 Color adjustment submenu The Output Effects Submenu adjusts color variable of the output image, such as contrast and brightness, saturation, hue and gammacorrections. • The RGB Contrast and Brightness settings are adjustablewithin a range of 0% to 200%. The default sett...

6. GUI orientation • Alignment Test pattern: a special test pattern designed toassist projectionist in aligning adjacent projectors • Data Doubling: H or V Overlap width. The adjustmentcan be made my moving the slider or entering the valuemanually in the box Feathering submenu • First, select the re...

6. GUI orientation 6.17 Programming Menu General In the programming page is where the event is set up and everything comes together. Users can de fi ne sources from inputs; assign layers and backgrounds into screens and create User keys and presets. Description Image 6-32 1 Sources area This area co...

6. GUI orientation Input, Sources and layer example Image 6-34 Source Area description There are 2 tabs in this section: • Source: Lists Inputs and Sources available in the system. Sources are listed after the input and can be view by clicking on thearrow next to the Input name. • Background: Lists ...

6. GUI orientation Once the picture is selected it is shown in the thumbnail area. Pictures are associated with inputs. If an input is deleted, then thepicture also will be deleted How to delete sources To Delete Sources:1. Click on the Delete Source(s) button. The Delete Source(s) button turns in r...

6. GUI orientation Image 6-37 Thumbnail view Image 6-38 R5905948 E2 12/12/2014 111

6. GUI orientation 6.19 Programming Menu > Diagram area General The middle of the Programming Page is the Programming diagram area where the Program , Preview and AUX screens are com- posed. Description Each Program/Preview screen can be viewed individually or all of the screens can be shown simu...

6. GUI orientation Image 6-40 Next a source from the Input panel on the left hand side can be dragged into the layer. Image 6-41 Alternatively, an Input or a source can be dragged into the Preview screen directly as long as there are available layers. Image 6-42 If the available layer is already in ...

6. GUI orientation Z-Order The layer priority (z-order) is based by the order they are added in destination menu.The layers that are added fi rst have the lowest priority. For example; layer1 is lower priority than layer2. Layer2 is lower priority than layer3. Freeze Note: When a layer is frozen, th...

6. GUI orientation Priority Image 6-46 1 Moves the selected layer up in priority and swaps with the layer previously above. 2 Moves the selected layer to the top of the priority and swaps it with the layer previously on top. 3 Moves down in priority and swaps the z-order of the selected layer with t...

6. GUI orientation 1 Full Screen Vertical takes the selected PIP(s) to full screen, using the source’s height as the guide. If borders are on, they will be taken into account so that they are visible. 2 Full Screen Horizontal takes the selected PIP(s) to full screen, using the source’s width as the ...

6. GUI orientation Preview transitions to Program according at the rate indicated in the rate box following the s-curve pattern. The layer on Programdoes NOT fade in preview at the same time. The layer on Program appears in Preview when the transition is completed. Cut Instantly transitions the Prev...

6. GUI orientation 6.22 Programming Menu > Adjustment area > Layer con fi guration General In the Layer menu, users can manage the layer in the selected destination and update its attributes. Layer con fi guration menu description Layer con fi guration menu is accessed by clicking on the Layer...

6. GUI orientation Or,Select the layer from the preview canvas. The layer is selected. Image 6-55 When the layer is selected and is visible on the canvas, it will have a blue highlight around the layer. 2. Click on the Adjust tab that is on the top of the adjustment area. The layer adjustment panel ...

6. GUI orientation Image 6-56 Once the two keyframes are de fi ned, the PIP can move between the two positions by pressing the green arrow buttons. The rate for the movement is adjusted by changing the number in the corresponding box. Any of the two keyframes can be deleted when the keyframe is high...

6. GUI orientation Layer adjustment panel > Layer Window adjustment The following PIP Adjustment Menu functions are provided: (All fi gures are in pixels) • H Size — adjusts the PIP’s horizontal size. • V Size — adjusts the PIP’s vertical size. • H Position — indicates the PIP’s position, relativ...

6. GUI orientation Layer adjustment panel > Layer Effects adjustment • RGB Contrast and Brightness settings are adjustable withina range of 0% to 200%. The default setting for all of theseproperties is 100%. • Gamma is adjustable within a range of 0.3 to 3.28. Thedefault setting is 1.0. • Hue is ...

6. GUI orientation 6.23 Programming Menu > Adjustment area > Background con fi guration General In the Layer menu, users can also manage the backgrounds. Two background channels are provided per destination (BG A and BGB), each of which appears at the system’s lowest priority — visually in bac...

6. GUI orientation • Background color can be adjusted by updating the Red /Green / Blue slider or edit box. The selected color is shownin the Current Color row. • The square buttons on the bottom of Current Color are quick shortcuts to primary colors. Click on any one of themto select that color for...

6. GUI orientation Search edit box Search User keys by name. Apply Selected Selected key is applied to the selected layer on Preview and on Program if “Modify on Program is enabled”. R5905948 E2 12/12/2014 129

6. GUI orientation 6.26 Programming Menu > Adjustment area > Source adjustment General The Source adjustments are shown on the Adjust panel when a layer with a valid Source is selected. The Source adjustment controlsdoes not appear when you select the Source by itself. Also note that the adjus...

6. GUI orientation Color adjustment • RGB Contrast and Brightness settings are adjustable withina range of 0% to 200%. The default setting for all of theseproperties is 100%. • Gamma is adjustable within a range of 0.3 to 3.28. Thedefault setting is 1.0. • Hue is adjustable within a range of -180 to...

6. GUI orientation 6.27 Programming Menu > Adjustment area > Global Transition Rate/Trans/Cut General At the bottom of the adjustment panel, is the transition rate and type buttons. These actions are executed for the selected Destina-tions. Description These controls are disabled if no Destina...

6. GUI orientation 6.28 Multiviewer (MVR) Menu General E2 includes a dedicated Multiviewer that enables multiple sources (inputs, Backgrounds, outputs) to be displayed on one or twomonitors. Multiviewer Menu is the module used to setup the Multiviewer outputs. Description This menu is accessible by ...

6. GUI orientation 6.30 Multiviewer Menu > Multiviewer Layout area General This part of the Multiviewer Menu allows a user to add and position sources in Multiviewer outputs. Description The tabs on the top of the layout panel area allow the user to view the two outputs together or individually. ...

6. GUI orientation One line of text is provided. The UMD area provides for 16 characters. If the text is too long it will be terminated with “…”. The background color is adjustable; the default color is gray. The UMD color will go red in case sync is lost. Border The border width is fi xed at 5 pixe...

6. GUI orientation 6.31 Multiviewer Menu > Modi fi er area General This area is speci fi cally for widow adjustments on Multiviewer outputs. Description The area is broken up into several sub areas. The left side is for alignment and position of the window. The right is for misc. controls. Window...

6. GUI orientation 6.32 Multiviewer Menu > Adjustment area General Situated on the right hand side of the screen is the Adjustment area. In this area the user can con fi gure the color and sizing of each multiviewer windows. Description There are several tabs in this area: • Output colors : Provi...

6. GUI orientation 6.36 Settings Menu > WebKit area General Main work area of the Setting Menu , where the user has access to a set of functions directly provided by the E2. All of the functions described in this section can also be performed by launching the web app directly fromthe browser outs...

6. GUI orientation Image 6-72 Outputs This menu presents a list of the output cards installed in the system. The status column indicates whether any errors have beendetected. Detailed diagnostics tests for each card are performed by selecting the diagnostics button under the action column. 146 R5905...

6. GUI orientation 6.40 Settings Menu > WebKit area > Tools > Backup & Restore General In this menu the user can store presets, user keys and other system settings on the computer. The menu also allows the user torestore a previously stored system fi le. Image 6-82 How to backup presets...

6. GUI orientation The Dialog box will close and a new window appears displaying the location and name of the stored compressed fi le. Image 6-84 4. Click on OK . How to restore presets, user keys and system settings The following procedure allows the user to restore a backed up fi le into the E2: 1...

7. System Setup 7.1 Setup Prerequisites Prerequisites Before starting to set up your E2 system, please review the following prerequisites: • Ensure that you are familiar with front panel menus and EM GUI software.- For details on all menus, please refer to chapter "Front Panel Menu orientation&#...

7. System Setup 7.2 System setup sequence Set up from A to Z This section provides a top level view of the entire E2 setup procedure, plus links to each individual sequence. For the optimum E2 setup, it is recommended that you follow all procedures in the order outlined below. Set up from A to Z 1. ...

7. System Setup 7.3 Power up and Status check General Use the following steps to power up your E2 system and check system status. Prerequisite • Ensure that your system is properly installed and cabled. • Ensure that you are familiar with the System Menu . For details on all menus, please refer to c...

7. System Setup 7.4 Return to factory default General Prior to performing any setup procedures, it is recommended that you perform a factory reset — in order to reset all input, outputand source mappings to their default values. Particularly for customers in the events and rental marketplace, this p...

7. System Setup 7.5 Communication setup General In this procedure, you will set up communication between the E2 and the local network. Prerequisite • Ensure that you are familiar with the Ethernet Menu . For details on this menu, please refer to chapter "System menu > Eth- ernet", page 56...

7. System Setup 7.6 Restoring the system This step in the E2 setup procedure is optional. If there is not backup available or if you decide to con fi gure your unit from scratch, please move to the next step to continue the procedure. General In this procedure, you will restore your system con fi gu...

7. System Setup 7.7 User preference setup General This procedure enables you to set a variety of important user preferences and options. Prerequisite • Ensure that you are familiar with the Black Invalid menu. For details on this menu, please refer to chapter "System menu > Black Invalid"...

7. System Setup 7.8 Saving the setup General In this procedure, you will save all system setup parameters to non-volatile memory. Prerequisite • Ensure that you are familiar with the Save All function. For details on this menu, please refer to chapter "Save All", page 66. Save all system set...

7. System Setup 7.9 Backing up the system General In this procedure, you will back up your system con fi guration to a USB drive. Prerequisite • Ensure that you are familiar with the USB device (Backup/Restore) Menu . For details on this menu, please refer to chapter "System menu > USB device...

7. System Setup 7.10 Con fi guration Menu > Initial Setup General In this procedure, you will run the Event Master Control Software, verify communication between the E2 and the program to the localnetwork and perform basic setup. Prerequisite • Ensure that you are familiar with the Con fi guratio...

7. System Setup 7.12 Con fi guration Menu > Add Inputs General In this procedure, you will add Inputs to the system . Prerequisite • Ensure that you are familiar with the Con fi guration Menu . For details on this menu, please refer to chapter "Con fi guration Menu", page 76 If more than ...

7. System Setup 7.13 Con fi guration Menu > Add Outputs General In this procedure, you will add Outputs to the system . Prerequisite • Ensure that you are familiar with the Con fi guration Menu . For details on this menu, please refer to chapter "Con fi guration Menu", page 76 If more tha...

7. System Setup 7.14 Con fi guration Menu > Add Screen Destinations & Layers General In this procedure, you will Add Screen Destinations from the de fi ned outputs. Prerequisite • Ensure that you are familiar with the Con fi guration Menu . For details on this menu, please refer to chapter &#...

7. System Setup 7.15 Con fi guration Menu > Add Aux Destinations General In this procedure, you will Add Aux Destinations from the de fi ned outputs. Prerequisite • Ensure that you are familiar with the Con fi guration Menu . For details on this menu, please refer to chapter "Con fi guration ...

7. System Setup 7.16 Con fi guration Menu > Add MVR Outputs General In this procedure, you will add MVR Outputs to the system. Prerequisite • Ensure that you are familiar with the Con fi guration Menu . For details on this menu, please refer to chapter "Con fi guration Menu", page 76 If m...

7. System Setup 7.17 Programming Menu > Select Thumbnails for Backgrounds General In this procedure, you will add select thumbnails for the Background Sources. Prerequisite • Ensure that you are familiar with the Programming Menu . For details on this menu, please refer to chapter "Programmin...

7. System Setup 7.18 Programming Menu > Select Thumbnails for Inputs General In this procedure, you will add select thumbnails for the Input sources. Prerequisite • Ensure that you are familiar with the Programming Menu . For details on this menu, please refer to chapter "Programming Menu"...

7. System Setup 7.19 Programming Menu > Create Sources from Inputs General In this procedure, you will create sources from the Input sources. Prerequisite • Ensure that you are familiar with the Programming Menu . For details on this menu, please refer to chapter "Programming Menu", page ...

7. System Setup 7.20 Programming Menu > Drop backgrounds into Screen Destinations General In this procedure, you will drop backgrounds into Screen Destinations. Prerequisite • Ensure that you are familiar with the Programming Menu . For details on this menu, please refer to chapter "Programmi...

7. System Setup 7.21 Programming Menu > Drop Layers into Screen Destinations & Sources into layers General In this procedure, you will drop Layers into Screen Destinations & Sources into layers. Prerequisite • Ensure that you are familiar with the Programming Menu . For details on this me...

7. System Setup 7.22 Programming Menu > Drop Inputs to Aux Destinations General In this procedure, you will drop Inputs into Aux Destinations. Prerequisite • Ensure that you are familiar with the Programming Menu . For details on this menu, please refer to chapter "Programming Menu", page...

7. System Setup 7.23 Multiviewer Menu > Drop Inputs, Backgrounds and Destinations Make sure that you have assigned connectors to MVR outputs before you proceed. General In this procedure, you will setup the Multiviewer outputs to the MRV monitors.. Prerequisite • Ensure that you are familiar with...

8. Updating firmware 8.1 Upgrading fi rmware using the USB port Necessary tools USB drive (Not supplied by Barco) formatted in FAT32. How to upgrading fi rmware 1. Ensure that your fl ash drive is formatted to use the FAT32 fi le system. If necessary, reformat the drive as described in the following...

8. Updating firmware Preparing the fl ash drive with the upgrade fi le. 1. Download the software upgrade for free from Barco’s website (URL: http://www.barco.com ). Click on myBarco and login to get access to secured information. Registration is necessary. Note: If you are not yet registered, click ...

8. Updating firmware 8.2 Upgrading fi rmware using the web Upgrade The upgrade operation begins with a step of validation to check if a new version is available. How to upgrading fi rmware 1. Verify that the E2 has internet access. Contact your system administrator if necessary. 2. Select Setup >...

9. General operation example 9. GENERAL OPERATION EXAMPLE About this chapter The application below is presented to demonstrate the basic E2 operation. The example provides the user a step-by-step setup andoperation instructions in order to meet some speci fi c event requirements. Overview • Event re...

9. General operation example 9.1 Event requirements Description Inputs for the event are provided from a Windows PC, two AJA KiPROs fi le recorders, an Apple Macbook and two video cameras. Several outputs are required as follows: • Two program outputs for the projectors dedicated to the Main screen....

9. General operation example 9.2 Preliminary Application Diagram Image 9-2 wiring Connect the input and output devices to the E2 as follows: Signal Type Device Name Content Connector Type Slot-Connectors Input CAM1 Audience camera 3G-SDI 4-1 Input CAM2 Stage Camera 3G-SDI 4–3 Input PC Background DVI...

9. General operation example 9.3 Control Software Operation Overview In this section we will use the control software (Event Master Control Software) to setup the E2 and create presets and user keys tobe used during the event. We will follow the steps sequentially outlined in diagram bellow. Work fl...

9. General operation example 9.4 Con fi guration Menu Overview Here, we de fi ne E2 components by adding inputs, backgrounds, outputs and destinations. C1: Initial Setup 1. When you connect to an actual unit, instead of working of fl ine, the software should connect automatically. The unit is listed...

9. General operation example Image 9-8 Note: The “N/A” at this end refers to the destinations that will be added next. C5 – Part1: Add Site Screen Destinations In this section we will create the Site Screen Destination and assign two layers.1. Click on the Destination tab to de fi ne destinations fo...

9. General operation example Image 9-9 C6: Add Aux Destinations 1. From the diagram area click on the DSM output. The connector will be highlighted. 2. Click on the +Add Aux Destination blue button to assign the DSM output to an Aux destination. 3. When the Aux destination is created a box appears n...

9. General operation example 9.5 Programming Menu Overview The programing Menu is accessed by clicking on the Programming icon on the left hand side of the screen. The area in the middlewill display a composite of the two screen destinations and the Aux destination created in the previous section. W...

9. General operation example Image 9-14 P2: You can skip this step if you don’t want thumbnail images to represent the inputs/sources. In this case,the layers in the destinations area will be black and noted only by the assigned name. P2: Select thumbnails for Inputs 1. From the left hand side, clic...

9. General operation example Image 9-15 P3: Created Additional Sources from Inputs As noted previously, a source is generated automatically for each input. For this application, only one sourcewill be used for each input, so no additional sources need to be created. Therefore, in this example this s...

9. General operation example Image 9-16 P5: Drop Layers into Screen Destinations & Sources into layers In this step we will add layers into each Destination, assign sources to layers and adjust their size and position parameters. Part1: Site Screen 1. On top, click on the Site Screen tab to only...

9. General operation example Image 9-17 4. Select the layer (white box) and then click on the Adjust tab on the top. 5. Select the Window Adjustment Icon and then unlock the aspect ration lock by clicking in the lock icon. R5905948 E2 12/12/2014 203

9. General operation example Image 9-22 P6: Drop Sources into Aux Screens (DMS Output) 1. On top click on the DSM tab. 2. Drag the CAM 1 input1 into the preview screen. Image 9-23 P7: In this application we will not save any user keys. All layers attributes will be saved. R5905948 E2 12/12/2014 207

9. General operation example P7: Create user Keys and Presets 1. Select the Site screen destination and the layer in preview. 2. Under the Preset tab click in the “Save to new Preset” button. 3. Edit the name to re fl ect the source that is on Preview. 4. Repeat the previous steps to save 3 more pre...

9. General operation example Image 9-27 Setup the “Program/Preview” window 1. Click on the top tab that is labeled “MVROut2”. 2. Click on the Destination tab and the top of the right hand side. 3. Drag the Program and Previews under the Site and Main Screens into the window area. 4. Resize and arran...

10. Maintenance 10. MAINTENANCE About this chapter This chapter describes how to service the E2 by replacing individual components. Simple servicing E2 is based on a modular design that ensures easy serviceability. Users can swap most of the E2 components in the case ofdamage, without shiping the un...

10. Maintenance 10.1 E2 unit Overview Orientation and main components Image 10-1 T Top 6 Mother Board F Front 7 Top Cover 1 Front Panel Knob 8 Front Brackets 2 VFD Display 9 EMI Filter 3 Front Cover Assembly 10 1RU Fan Tray 4 Rack Ears 11 3RU Fan Tray 5 VPU cards 12 Chassis R5905948 E2 12/12/2014 21...

10. Maintenance 10.2 Process Overview Flow chart Image 10-2 216 R5905948 E2 12/12/2014

10. Maintenance 10.3 Spare Parts Serviceable by all users Spare Parts list P/N Description Comments R767241K VFD Display assembly R767246K VFD Filter R767260K Front Panel board R767261K System Power board R767263K Heatsink fan One for each Input, Output, Link and VPU card R767264K CPU module R767265...

10. Maintenance 10.4 Rear I/O and Link Cards Image 10-3 Overview Image 10-41 Chassis 2 I/O and Link Cards Concerned parts R9004740 DVI Input R9004741 SDI Output R9004742 SDI Input R9004743 HDMI Output R9004744 DP/HDMI Input R9004745 DVI Output (*) R9004746 Link Card (*) Not available in release 1) N...

10. Maintenance Image 10-5 How to install a card To install a card follow the same procedure in the reverse order. Apply a little pressure on the card until it is fully inserted in the back plane connector. R5905948 E2 12/12/2014 219

10. Maintenance 10.6 Front Cover Assembly Image 10-8 Overview Image 10-91 Front Cover Assembly 2 Front Brackets 3 EMI Filter 4 1RU Fan Tray 5 3RU Fan Tray 6 VPU Cards Necessary tools 1 x Screwdriver HEX 0.05" 7.05" (Provide by Barco in the original package). Image 10-10 How to remove the Fro...

10. Maintenance At this point there are still 3 cables connecting the Front cover to the unit. Image 10-121 Front Panel Connector 2 VFD Connector 3 USB Connector 3. Pull the latches away from connectors and gently pull the fl at Front Panel away. 4. Remove cables as outlined in the related procedure...

10. Maintenance 10.8 EMI Filter Image 10-15 Concerned parts R767272K EMI Filter Necessary tools None. How to remove the EMI Filter 1. Remove the EMI fi lter by fi rst pulling gently the right side out and then untucking the left side from behind the key features. Image 10-16 How to install the EMI F...

10. Maintenance 10.9 3RU Fan Tray Image 10-18 Concerned parts R767271K 3RU Fan Tray Necessary tools 1 x Phillips Screwdriver #2 (optional). How to remove the 3RU Fan Tray 1. Loosen and unscrew the 4 thumbscrews holding the 3RU fan tray to the chassis. Note: You may need a screwdriver if the thumbscr...

10. Maintenance How to install the 1RU Fan Tray Follow the same procedure in the reverse order and in addition perform the following:1. Pass the USB and VFD cable through the grommet. Image 10-23 2. Make sure that the front panel fl at cable goes through the slot located on the right hand side. 3. L...

10. Maintenance 10.11 VPU Card(s) Image 10-24 Overview Image 10-251 Chassis 2 VPU cards Concerned parts R9004747 VPU Card Necessary tools 1 x Phillips Screwdriver #2 (optional). How to remove a VPU Card 1. Locate the VPU you need to replace. Note: There are 9 VPU slots. The fi rst slot on the left i...

10. Maintenance 10.12 Front Panel Knob Image 10-27 Before you proceed removing the Front panel knob you need to remove the Front Cover Assembly as outlinedin the related procedure. Necessary tools • Knob removal tool provided by Barco Image 10-28 • Flat head screwdriver or a tool with a sharp edge H...

10. Maintenance Image 10-30 How to install the Front Panel Knob To install the Front Panel Knob follow the same procedure in the reverse order. R5905948 E2 12/12/2014 231

10. Maintenance 10.13 Front Panel Mount Image 10-31 Necessary tools 1 x Phillips Screwdriver #2 How to remove the Front Panel Mount 1. Turn the Front Cover over and remove the four screws (4-40X.25) that secure the control panel mount to the front panel. Image 10-32 How to install the Front Panel Mo...

10. Maintenance 10.14 Front Panel Board Image 10-33 Concerned parts R767260K Front Panel Board Necessary tools 1 x Phillips Screwdriver #2 How to remove the Front Panel Board 1. Remove the two screws ( 4-40X.25) that secure the PCB to the front mount. Image 10-34 2. Move the PCB to the right and the...

10. Maintenance Image 10-35 How to install the Front Panel Board To install the Front Panel Board follow the same procedure in the reverse order. 234 R5905948 E2 12/12/2014

10. Maintenance 10.15 VFD Display Assembly Image 10-36 Before you proceed removing the VFD Display mount you need to remove the Front Cover Assembly as out-lined in the related procedure Concerned parts R767241K VFD Display Assembly Necessary tools 1 x Phillips Screwdriver #2 How to remove the VFD D...

10. Maintenance 10.17 Bottom Panel Necessary tools 1 x Phillips Screwdriver #2 How to remove the Bottom Panel 1. Turn the unit over to remove the bottom panel. The bottom panel is composed of two pieces. 2. Remove the 4 black round-head screws (4-40x1/4) that attach the panels to the side of the uni...

10. Maintenance 10.18 Solid-State Memory Image 10-41 Before you proceed removing the Solid State Memory you need to remove the Bottom Panel as outlined in therelated procedure. The solid-state memory can also be replaced after the System Power board is removed from the unit. Overview Image 10-421 Sy...

10. Maintenance Image 10-43 How to install the Solid State Memory To install the Solid State Memory follow the same procedure in the reverse order. R5905948 E2 12/12/2014 239

10. Maintenance 10.19 System Battery Image 10-44 Before you proceed removing the System Battery you need to remove the Bottom Panel as outlined in therelated procedure. The System Battery can also be replaced after the System Power board is removed from the unit. Concerned parts V327007 Battery Nece...

10. Maintenance 10.20 CPU Module Image 10-47 Before you proceed removing the CPU module you need to remove the Bottom Panel as outlined in the relatedprocedure. Overview Image 10-481 Chassis 2 CPU Module 3 Bottom Panel Part 1 4 System Card. 5 Bottom Panel Part 2 Concerned parts R767264K CPU module N...

10. Maintenance Image 10-49 How to install the CPU module To install the CPU module follow the same procedure in the reverse order. R5905948 E2 12/12/2014 243

10. Maintenance Image 10-50 2. Pull the Power supply out of its slot by pulling on the handle. How to install Power Supply 1. Insert the Power Supply into the slot. Note: The card edge should be at the top of the power supply as shown in the drawing. 2. Push the power supply completely inside the sl...

10. Maintenance Concerned parts R767261K System-Power Board Necessary tools • 1 x Phillips Screwdriver #2 • Hex Screwdriver How to remove the System-Power board 1. Unplug the USB, VFD, 3RU and 1RU cables that are plugged on the top side of the board and are visible when the bottom panel is removed. ...

10. Maintenance Top side Image 10-54 1 USB connector 3 3RU connector 2 VFD connector 4 1RU connector 248 R5905948 E2 12/12/2014

10. Maintenance Bottom side Image 10-55 1 Keyboard connector 3 Ethernet connector 2 Genlock connector R5905948 E2 12/12/2014 249

10. Maintenance 10.23 Genlock Assembly Image 10-56 Overview Image 10-571 Chassis 2 Genlock Assembly Concerned parts R9004748 Genlock Assembly Necessary tools 1 x Phillips Screwdriver #2 How to remove the Genlock Assembly 1. Remove the seven fl at head screws (4-40 X .25) that attach the Genlock asse...

10. Maintenance How to install the Genlock Assembly To install the Genlock Assembly follow the same procedure in the reverse order. 252 R5905948 E2 12/12/2014

10. Maintenance 10.24 USB Cable Image 10-60 The USB cable is connected to the USB extension cable (the cable that is connected to the System-Powerboard). This procedure provides instructions how to disconnect it from both sides of the cable. Concerned parts R767269K Cable Kit Set Necessary tools • 1...

10. Maintenance Image 10-62 9. Remove the USB cable. How to install the USB cable To install the USB cable follow the same procedure in the reverse order. R5905948 E2 12/12/2014 255

10. Maintenance 10.25 USB Extension Cable Image 10-63 The USB Extension cable connects the USB cable to the System Power board. This procedure provides in-structions on how to disconnect the cable on both sides. Concerned parts R767269K Cable Kit Set Necessary tools 1 x Phillips Screwdriver #2 How t...

10. Maintenance How to install the USB Extension cable To install the USB Extension cable follow the same procedure in the reverse order. R5905948 E2 12/12/2014 257

10. Maintenance 10.26 VFD Cable Image 10-66 The fl at ribbon VFD cable connects the VFD assembly to the System Power board. This procedure provides instructions on how to disconnect the cable on both sides. Concerned parts R767269K Cable Kit Set Necessary tools • 1 x Phillips Screwdriver #2 • Hex Sc...

10. Maintenance Image 10-68 4. Turn the unit upside down and remove the bottom panel (Follow the instructions provided in the bottom panel removal section). 5. Locate the VFD cable that is plugged on the System-Power board. Image 10-69 6. Pull the cable out of the unit . How to install the VFD Cable...

10. Maintenance Image 10-71 8. Carefully remove the cable from the unit. How to install the Keyboard Cable To install the Keyboard Cable follow the same procedure in the reverse order. There is a key on the connector to prevent incorrect insertion of the cable. R5905948 E2 12/12/2014 261

10. Maintenance 10.28 Genlock Cable Image 10-72 The fl at ribbon Genlock cable connects the Genlock Assembly to the System-Power board. This procedure provides instructions on how to disconnect the cable on both sides. Make sure the latches are fully engaged to prevent the cable from coming loose. C...

10. Maintenance Image 10-73 7. Remove the cable from the unit. How to install the Genlock Cable To install the Genlock Cable follow the same procedure in the reverse order. There is a key on the connector to prevent incorrect insertion of the cable. Make sure the latches are fully engaged to prevent...

10. Maintenance 10.29 Ethernet Cable Image 10-74 The Ethernet cable connects the Genlock board to the System Power board. This procedure provides instruc-tions on how to remove the cable from both sides. Concerned parts R767269K Cable Kit Set Necessary tools 1 x Phillips Screwdriver #2 How to remove...

10. Maintenance 10.30 3RU Fan Cable Image 10-76 The 3RU cable assembly provides power to the 3RU fans from the System-Power board. One side of the cable is attached to a metal bracket that is accessible after the 3RU fan tray is removed. Theother side of the cable assembly connects to the System-Pow...

10. Maintenance Image 10-81 8. Remove the 3RU cable by gently pushing it out. How to install the 3RU Fan Cable To install the 3RU Fan Cable follow the same procedure in the reverse order. R5905948 E2 12/12/2014 267

10. Maintenance 10.31 1RU Fan Cable Image 10-82 The 1RU cable assembly provides power to the 1RU fans from the System-Power board. One side of the cable is attached to a metal bracket that is accessible after the 3RU and the 1RU fan trays areremoved. The other side of the cable assembly connects to ...

10. Maintenance Image 10-87 8. Remove the 1RU cable by gently pushing it out. How to install the 1RU Fan Cable To install the 1RU Fan Cable follow the same procedure in the reverse order. R5905948 E2 12/12/2014 271

10. Maintenance 10.32 Rear Rack Ears Concerned parts R767273K Connector protector Necessary tools 1 x Phillips Screwdriver #2 How to remove Rear Rack-Ears 1. Remove the eight pan head screws (8-32x.31), four from each side, to detach the rear rack ears and connector protectors from the unit. Note: Y...

10. Maintenance 10.33 Front Rack-Ears Image 10-89 Concerned parts R767268K Rack Ears kit Necessary tools 1 x Phillips Screwdriver #2 How to remove Side Rack-Ears 1. Loosening and removing the eight (four on each side) pan head screws that secure the brackets to the chassis sides. Image 10-90 2. Remo...

10. Maintenance 10.34 Top Cover Image 10-91 Necessary tools 1 x Phillips Screwdriver #2 How to remove Top Cover 1. Remove the 12 screws from the two sides (6 in each side, 4-40x0.25) that are located towards the top side of the unit. 2. Remove the two (2) screws (4-40x0.25) located closer to the rea...

10. Maintenance 10.35 Top Card Guide Image 10-93 Necessary tools 1 x Phillips Screwdriver #2 How to remove Top Card Guide 1. Remove the 18 screws from the two sides (8 in each side, 6-32x0.25) that are located towards the bottom of the unit. 2. Remove the card guide cover by gently pulling it away f...

10. Maintenance 10.36 Motherboard Fan Image 10-95 Overview Image 10-961 Motherboard 2 Fan 3 Heatsink 4 Fan power cable Concerned parts R767265K Motherboard Heatsink & Fankit Necessary tools 1 x Phillips Screwdriver #2 How to remove Motherboard Fan 1. Remove the cable that provides power to the h...

10. Maintenance Disregard the heatsink from the spare kit. R5905948 E2 12/12/2014 277

11. Environmental information 11. ENVIRONMENTAL INFORMATION Overview • Disposal information • RoHS compliance • Production address R5905948 E2 12/12/2014 279

11. Environmental information 11.1 Disposal information Disposal Information Waste Electrical and Electronic Equipment This symbol on the product indicates that, under the European Directive 2012/19/EU governing waste from electrical and electronic equipment, this product must not be disposed of wit...

11. Environmental information 11.2 RoHS compliance 中 国 大 陆 RoHS (Chinese Mainland RoHS) 根 据 中 国 大 陆 《 电 子 信 息 产 品 污 染 控 制 管 理 办 法 》（ 也 称 为 中 国 大 陆 RoHS ） ， 以 下 部 分 列 出 了 Barco 产 品 中 可 能 包 含 的 有 毒 和 / 或 有 害 物 质 的 名 称 和 含 量 。 中 国 大 陆 RoHS 指 令 包 含 在 中 国 信 息 产业 部 MCV 标 准 ： “ 电 子 信 息 产 品 中 有 毒 物 质 的 限 量 ...

11. Environmental information 11.3 Production address Factory Barco Inc. 3000 Technology Road Angleton, TX 77515 USA R5905948 E2 12/12/2014 283

A. Specifications A. SPECIFICATIONS About this annex This chapter gives an overview of the speci fi cations of the E2. R5905948 E2 12/12/2014 285

A. Specifications A.1 Speci fi cations of E2 Overview Genlock Genlock: Reference Input/Loop on BNC connectors; Analog Bi-level and Blackburst atSD and Tri-level at HD Communication Ethernet RJ-45, 1000/100/10 Mbps autosense Dimensions • Height: 17.8 cm (7.0 in) - 4 RU Rackmount • Width: 43.2 cm (17....

A. Specifications • EDID version 1.3 compatible • HDCP version 1.4 compatible SDI • SD/HD/3G SDI (6G ready) on BNC connector • Formats:- SD Formats: SD-SDI per SMPTE 259M-C (NTSC/PAL resolution)- HD Formats: HD-SDI per SMPTE 274M, 296M, 2048- 3G Formats: 3G-SDI per SMPTE 424M, Barcolink • 6G Ready (...

A. Specifications A.2 Standard connector pinouts DisplayPort connector pinouts The following fi gure illustrates the DisplayPort connector. Image A-1DisplayPort connector The following table lists the DisplayPort connector pinouts. DisplayPort connector Pin Signal Pin Signal 1 ML_Lane 0 (p) 11 GND 2...

B. Remote Control Protocol B. REMOTE CONTROL PROTOCOL About this annex This chapter lists and provides details for the E2 remote control commands. In release 1 only a limited number of commands are available. Additional commands will be implemented ina future release! R5905948 E2 12/12/2014 291

B. Remote Control Protocol B.1 E2 Remote control Introduction General The user can remotely control the E2 via a telnet connection to the unit’s IP address. How accessing the E2 remotely To access the E2 remote commands, use the following procedure:1. In a command prompt window, type a telnet comman...

B. Remote Control Protocol B.2 E2 Remote Commands General This section lists the E2 remote commands, sorted by name. ATRN • Description: Performs an Auto Transition on the currently active destinations. The currently selected Effect type, rate and edgewidth will be used to transition preview to prog...

C. Troubleshooting C.1 Troubleshooting List Problem solving Problem Possible cause Remedy E2 doesn’t start The Power supplies are not connected toa valid power source Make sure that at least one power supplyis connected to a valid power source.Make sure that the supplies are wellinserted in their sl...

D. Warranty D.1 About Warranty and RMA Warranty All video products are designed and tested to the highest quality standards and are backed by a full 3-year parts and labor warranty.Warranties are effective upon delivery date to customer and are non-transferable. Barco warranties are only valid to th...

Index INDEX Numerics/Symbols 6G SDI Input Card 35 6G SDI Output Card 42 A About 6 User Guide 6 About E2 5About Setup menu 51 About Status menu 50About the System menu 52 About Warranty and RMA 300 Add destination 100 Add device 77Add device (Manually) 77Add Input 86Add Output 94Address 283Adjustment...