Barco HDX Series - Manual

1. Introduction 1.3 Touring kit Order info & content of the kit When ordering the Touring kit for HDX series, refer to article number R9864080. The table below gives an overview of the content of the kit. Article number Description Quantity R5905106 This installation manual 1 R9864060 Top Carry ...

2. Installation procedures 2. INSTALLATION PROCEDURES Overview • Installing the Bottom Carry Handle • Removing the Bottom Carry Handle • Installing the Top Carry Handle • Removing the Top Carry Handle • Allowed projector positions • Stacking projectors • Suspending the projector from a truss • Skewi...

2. Installation procedures 2.1 Installing the Bottom Carry Handle Necessary tools 17 mm open-end wrench How to install the Bottom Carry Handle? 1. Turn the projector upside down and remove the 4 feet (reference 1, image 2-1) by turning them anticlockwise. 1 Image 2-1 2. Turn out the stacking points ...

2. Installation procedures 2.2 Removing the Bottom Carry Handle How to remove the Bottom Carry Handle? 1. Remove the 4 bolts (reference 6, image 2-4). 6 Image 2-4 2. Remove the Bottom Carry Handle from the projector (image 2-5). Image 2-5 3. Install the 4 feet by turning them clockwise (image 2-6). ...

2. Installation procedures 2.3 Installing the Top Carry Handle Necessary tools 8 mm Allen wrench How to install the Top Carry Handle? 1. Position the Top Carry Handle on top of the projector so that the fi xation holes match the holes in the projector. 2. Turn in the 4 bolts (reference 1, image 2-7)...

2. Installation procedures 2.4 Removing the Top Carry Handle Necessary tools 8 mm Allen wrench How to remove the Top Carry Handle? 1. Turn out the 4 bolts (reference 1, image 2-8) and remove the 4 washers. 1 1 Image 2-8 2. Remove the Top Carry Handle from the projector. R5905106 TOP & BOTTOM CAR...

2. Installation procedures 2.5 Allowed projector positions C AUTION : Using the projector in a disallowed position can cause premature lamp failure. Which projector positions are allowed? With both the Top Carry Handle and Bottom Carry Handle installed, the projector can be placed in several positio...

2. Installation procedures 2.6 Stacking projectors The procedure below describes how to stack 2 projectors. The procedure to stack 3 projectors is analog. W ARNING : Never stack more than three (3) projectors. Failure to do so can cause serious injury or death. Necessary tools 8 mm Allen wrench How ...

2. Installation procedures 2.7 Suspending the projector from a truss W ARNING : Never suspend more than two (2) projectors. Failure to do so can cause serious injury or death. Introduction A projector can be suspended from a truss using rigging clamps. When a Bottom Carry Handle is installed on the ...

2. Installation procedures Image 2-23 8. Lift up the truss with projector to the desired height. Warning: Make sure the safety cable is installed with a minimum of play, so that the projector can only fall down for maximum20 cm. If necessary, wind the cable a few times around the truss before claspi...

2. Installation procedures 2.8 Skewing the projector How to skew the projector? 1. Turn the adjustment knob clockwise or anticlockwise to skew the projector as illustrated. Image 2-25 R5905106 TOP & BOTTOM CARRY HANDLE 28/06/2011 23

2. Installation procedures 2.9 Inclinating and/or rotating the projector How to inclinate and/or rotate the projector? 1. Turn the projector feet in or out to inclinate and/or rotate the projector as needed. Image 2-26 24 R5905106 TOP & BOTTOM CARRY HANDLE 28/06/2011

2. Installation procedures 2.10 Aligning stacked projectors How to align stacked projectors? 1. Project a hatch pattern with the reference projector. Note: In case of a table mount con fi guration the reference projector is the lowest projector and in case of a hanging con fi guration the reference ...