Page 2 - Copyright
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 2 Copyright © Barco. March 24, 2013 All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or st...
Page 3 - Trademarks; Company Address; Technical Support
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 3 Trademarks Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders. All brand and product names me...
Page 4 - Operators Safety Summary
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 4 Operators Safety Summary The general safety information in this summary is for operating personnel. Do not remove panels or covers There are no user-serviceable parts within ...
Page 5 - Warning
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 5 Terms in This Manual and Equipment Marking Warning Highlights an operating procedure, practice, condition, statement, etc., which, if not strictly observed, could result in i...
Page 8 - HANGE
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 8 C HANGE H ISTORY Rev Date ECP # Description Approved By 00 6/7/13 606947 User’s Guide GKOU 01 7/29/13 608395 User’s Guide MYRA 04 3/16/14 612461 Updated User’s Guide to inclu...
Page 9 - ABLE OF
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 9 T ABLE OF C ONTENTS 1 Introduction ..................................................................................................... 11 1.1 Key Features ....................
Page 10 - Firmware update
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 10 7.2.2 Input and output status .................................................................................. 35 7.2.3 Network setting ......................................
Page 11 - Introduction
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 11 1 Introduction The MATRIXPRO-II DVI 16x16 router enables users to switch up to 16 different DVI sources to 16 different digital displays. Any input source, whether it‘s a HD...
Page 12 - Notice Of Safe Usage
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 12 1.3 Notice Of Safe Usage We recommend you to read following warnings, precautions and information before operating the unit. ▪ Use of the equipment in a manner not specified...
Page 13 - Physical Description
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 13 1.4 Physical Description The MATRIXPRO-II DVI 16 X 16 router chassis is mountable on a 19” standard rack. Key buttons, LCD display and reset switch are on the front panel as...
Page 14 - Installation; EDID Configuration
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 14 2 Installation 2.1 Initialization ▪ Connect the provided AC power cord to AC power inlet and turn on the front panel switch ▪ The unit starts the initialization process. The...
Page 15 - EDID; INTERFACE
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 15 3) Auto Mix Mode: (The most advanced method) read all EDID information from the attached input devices. An information set optimized for all inputs is created and used to av...
Page 16 - Control Setup; ENTER
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 16 3 Control Setup The MATRIXPRO-II DVI 16x16 router can be controlled in various ways such as command input (RS-232, TCP/IP), Web GUI control panel (TCP/IP), Windows applicati...
Page 18 - Front Panel Operation
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 18 4 Front Panel Operation 4.1 LINK mode ▪ It configures input / output connections for cross-switching. 1) Press LINK key button. 2) Press an input key button - LCD will displ...
Page 19 - Gateway
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 19 4.4 FUNCTION mode ▪ This function enables the configuration of the unit allowing it to be controlled by commands input or from the PC windows program ▪ By pressing the FUNCT...
Page 21 - Video Generator; Test Pattern Resolutions
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 21 4.4.6 Video Generator ▪ The Video Generator (Reference Output) allows you to select the test pattern you would like to output on the Reference Output connector. ▪ Input 1 an...
Page 24 - HDCP Configure; HDCP CONFIGURE
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 24 4.4.9 HDCP Configure Disabling HDCP Compatibility By default, the MATRIXPRO-II DVI 16X16 is an HDCP compatible Video Router. HDCP protected content received on a DVI input c...
Page 26 - PC Program Operation
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 26 5 PC Program Operation Run the setup.exe to install MATRIXPRO-II DVI 16x16 PC program. The Barco icon will be shown on the wallpaper. Double click it to launch PC program fo...
Page 27 - Set Config
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 27 5.1 Basic Setup Click on the Set Config button. The Set Config window (as shown below) will then open. From this window you can set the communication method, input and outpu...
Page 28 - Connect Info; Connect; Channel Name; Wall
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 28 5.1.1 Connect Info ▪ Select the connection method to be either RS-232 and Ethernet (UDP) by clicking the corresponding radio buttons. ▪ For RS-232 control, enter the COM por...
Page 31 - Figure 5-5: Software GUI Input and Output status screen; Input / output connection
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 31 The left side of the control application shows the signal connection, resolution, EDID, and routing status of the inputs and outputs. Figure 5-5: Software GUI Input and Outp...
Page 32 - Output channel status
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 32 5.3.3 Output channel status ▪ Green LEDs above the output channel number indicate Hot Plug Detection (HPD) from display. For example CH07 is connected to a display. ▪ The co...
Page 33 - Web control panel operation; LINK; SEND
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 33 6 Web control panel operation The Web control panel operation provides a user-friendly graphic interface and easy access to control the MATRIXPRO-II DVI 16x16. Some function...
Page 35 - Table 7-3: Input and output status command examples
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 35 ▪ After all input commands, MATRIXPRO-II DVI 16x16 sends back replies to conform the execution of commands. ▪ Input and output port number range from 1 to 16 and prefix, ‘0’...
Page 36 - Network setting; Table 7-4: Network setting command examples; Video generator settings
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 36 7.2.3 Network setting ▪ Sets the IP, Gateway, Subnet mask, MAC address and UDP port number. ▪ Requests current network setting. Command Description and reply NETGW=192.168.1...
Page 38 - Monitor output port settings; Table 7-7: Monitor output setting command examples; EDID control command; Table 7-8: EDID setting command examples
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 38 7.2.5 Monitor output port settings ▪ Makes an input connected to the Monitor Output port. ▪ Requests input port that is currently connected to the Monitor Output port. Comma...
Page 39 - HDCP Setting
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 39 List Number Horizontal Vertical Name Aspect Ratio 01 800 600 SVGA 4:3 02 1024 768 XGA 4:3 03 1280 720 HD 720 16:9 04 1366 768 WXGA 16:9 05 1400 1050 SXGA+ 4:3 06 1440 900 WX...
Page 40 - Preset Control Commands; Table 7-11: Preset setting command examples; Baud rate setting for RS-232; Table 7-12: Baud rate setting command examples
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 40 7.2.8 Preset Control Commands ▪ Allows user to save routings under a preset number and to later load the preset routings. Up to 10 presets can be saved. Command Description ...
Page 41 - ‘File to be programmed in the Flash’
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 41 7.2.10 Control lock command ▪ Locks and unlocks the controls such as Web, RS-232, TCP/IP and UDP. ▪ Requests open status of controls. ASCII Description WL Web control lock W...
Page 43 - All Done
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 43 box as shown below. 8. After 1 to 2 minutes, and “ All Done ” message will be shown. Then the firmware upload is completed.
Page 45 - HDCP notes
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 45 9 HDCP notes HDCP stands for High-Bandwidth Digital Content Protection, an industry-wide copy protection scheme that is used to prevent the potential interception of digital...
Page 46 - Specifications; Video
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 46 10 Specifications Video INPUTS DVI ●All single-link DVI digital formats up to 165 Mhz, per DVI 1.0 specification ● EDID version 1 .3 compatible Video OUTPUTS DVI Formats: al...
Page 47 - Warranty; Technical Support / Customer Service
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 47 11 Warranty Warranty All video products are designed and tested to the highest quality standards and are backed by a full 3-year parts and labor warranty. Warranties are eff...
Page 48 - Contact Information; Sales Contact
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 04 48 12 Contact Information Barco Inc. 3078 Prospect Park Drive Rancho Cordova, California 95670 USA • Telephone: (916) 859-2500 • Fax: (916) 859-2515 • Website: www.barco.com Sa...
