Page 2 - Copyright
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 2 Copyright © Barco. March 24, 2013 All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or st...
Page 3 - Trademarks; Company Address; Technical Support
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 3 Trademarks Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders. All brand and product names me...
Page 4 - Operators Safety Summary
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 4 Operators Safety Summary The general safety information in this summary is for operating personnel. Do not remove panels or covers There are no user-serviceable parts within ...
Page 5 - Warning
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 5 Terms in This Manual and Equipment Marking Warning Highlights an operating procedure, practice, condition, statement, etc., which, if not strictly observed, could result in i...
Page 8 - HANGE
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 8 C HANGE H ISTORY Rev Date ECP # Description Approved By 00 6/7/13 606947 User’s Guide GKOU 01 7/29/13 608395 User’s Guide MYRA
Page 9 - ABLE OF
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 9 T ABLE OF C ONTENTS 1 Introduction ..................................................................................................... 11 1.1 Key Features ....................
Page 10 - Firmware update
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 10 7.2.2 Input and output status .................................................................................. 32 7.2.3 Network setting ......................................
Page 11 - Introduction
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 11 1 Introduction The MATRIXPRO-II DVI 16x16 router enables users to switch up to 16 different DVI sources to 16 different digital displays. Any input source, whether it‘s a HD...
Page 12 - Notice Of Safe Usage
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 12 1.3 Notice Of Safe Usage We recommend you to read following warnings, precautions and information before operating the unit. ▪ Use of the equipment in a manner not specified...
Page 13 - Physical Description
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 13 1.4 Physical Description The MATRIXPRO-II DVI 16 X 16 router chassis is mountable on a 19” standard rack. Key buttons, LCD display and reset switch are on the front panel as...
Page 14 - Installation; EDID Configuration
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 14 2 Installation 2.1 Initialization ▪ Connect the provided AC power cord to AC power inlet and turn on the front panel switch ▪ The unit starts the initialization process. The...
Page 15 - EDID; INTERFACE
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 15 3) Auto Mix Mode: (The most advanced method) read all EDID information from the attached input devices. An information set optimized for all inputs is created and used to av...
Page 16 - Control Setup; ENTER
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 16 3 Control Setup The MATRIXPRO-II DVI 16x16 router can be controlled in various ways such as command input (RS-232, TCP/IP), Web GUI control panel (TCP/IP), Windows applicati...
Page 18 - Front Panel Operation
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 18 4 Front Panel Operation 4.1 LINK mode ▪ It configures input / output connections for cross-switching. 1) Press LINK key button. 2) Press an input key button - LCD will displ...
Page 22 - HDCP Configure; HDCP CONFIGURE
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 22 4.4.9 HDCP Configure Disabling HDCP Compatibility By default, the MATRIXPRO-II DVI 16X16 is an HDCP compatible Video Router. HDCP protected content received on a DVI input c...
Page 24 - PC Program Operation; Set Config
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 24 5 PC Program Operation Run the setup.exe to install MATRIXPRO-II DVI 16x16 PC program. The Barco icon will be shown on the wallpaper. Double click it to launch PC program fo...
Page 25 - Connect Info; Connect
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 25 5.1.1 Connect Info ▪ Select the connection method to be either RS-232 and Ethernet (UDP) by clicking the corresponding radio buttons ▪ For RS-232 control, enter the COM port...
Page 26 - Channel Name; Wall; Video Generator; Set
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 26 5.1.2 Channel Name ▪ User can create specific names for all inputs and outputs to distinguish them ▪ On Fig 4.2, The name of Camera #1 was assigned to Input CH05 and Wall di...
Page 28 - Input / output connection; All Link; Input channel status
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 28 The left side of the control application shows the signal connection, resolution, EDID, and routing status of the inputs and outputs. 5.3.1 Input / output connection ▪ Click...
Page 29 - Output channel status
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 29 5.3.3 Output channel status ▪ Green LEDs above the output channel number indicate Hot Plug Detection (HPD) from display. For example CH07 is connected to a display. ▪ The co...
Page 30 - Web control panel operation; LINK; SEND
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 30 6 Web control panel operation The Web control panel operation provides a user-friendly graphic interface and easy access to control the MATRIXPRO-II DVI 16x16. Some function...
Page 32 - Table 7-3: Input and output status command examples
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 32 ▪ After all input commands, MATRIXPRO-II DVI 16x16 sends back replies to conform the execution of commands. ▪ Input and output port number range from 1 to 16 and prefix, ‘0’...
Page 33 - Network setting; Table 7-4 : Network setting command examples; Monitor output port setting; Table 7-5: Monitor output setting command examples; EDID control command
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 33 7.2.3 Network setting ▪ Sets the IP, Gateway, Subnet mask, MAC address and UDP port number. ▪ Requests current network setting. Command Description and reply NETGW=192.168.1...
Page 34 - Table 7-6: Monitor output setting command examples; HDCP Setting
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 34 Command Description and reply EDID=DE1,7,15! Default mode: Saves default EDID in input ports 1, 7 and 15. Reply: EDID=01DEF.! EDID=07DEF.! EDID=15DEF.! EDID=AUTO2,8,9! Auto ...
Page 35 - Table 7-7: Baud rate setting command examples; Control lock command; Table 7-9: Locking type and its ASCII data
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 35 ▪ Sets the RS-232 baud rate. MATRIXPRO-II DVI 16x16 supports 9600, 19200, 38400, 57600, 115200bps. ▪ Requests the current RS-232 baud rate. Command Description and reply RS2...
Page 36 - ‘File to be programmed in the Flash’
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 36 8 Firmware update 1. Using a Windows XP based PC, install the megaboot.exe program provided on a CD. 2. Click ① , Open of ‘File to be programmed in the Flash’ to select dire...
Page 38 - All Done
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 38 8. After 1 to 2 minutes, and “ All Done ” message will be shown. Then the firmware upload is completed.
Page 40 - HDCP notes
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 40 9 HDCP notes HDCP stands for High-Bandwidth Digital Content Protection, an industry-wide copy protection scheme that is used to prevent the potential interception of digital...
Page 41 - Specifications; Video
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 41 10 Specifications Video INPUTS DVI ●All single-link DVI digital formats up to 165 Mhz, per DVI 1.0 specification ● EDID version 1 .3 compatible Video OUTPUTS DVI Formats: al...
Page 42 - Warranty; Technical Support / Customer Service
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 42 11 Warranty Warranty All video products are designed and tested to the highest quality standards and are backed by a full 3-year parts and labor warranty. Warranties are eff...
Page 43 - Contact Information; Sales Contact
MatrixPRO-II DVI 16x16 Router ________________________________________________________________________ User’s Guide Rev. 01 43 12 Contact Information Barco Inc. 11101 Trade Center Drive Rancho Cordova, California 95670 USA • Telephone: (916) 859-2500 • Fax: (916) 859-2515 • Website: www.barco.com Sa...
