Barco 26-0904004-00 - Manual

Website:

Phone:

EMEA Support

www.barco.com/support/eSupport.aspx
0800900410

Quick Start Guide

Visibly yours

Quick Install and Setup

Barco Events USA

11101 Trade Center Drive
Rancho Cordova, CA
95670 • USA

ImagePRO-II User’s Guide

For complete details on all installation and operations procedures,
please refer to the ImagePRO-II User’s Guide.

PN 26-0904004-00 Rev 01

Getting Started

Setting Up Inputs

Setting Up Outputs

1. Connect power

— Ensure that power is

properly connected to the ImagePRO-II.

2. Connect inputs

— Connect all input sources to

the ImagePRO-II.

3. Connect outputs

— Connect the output(s) on

the ImagePRO-II to your projector(s) or other
target devices.

4. Turn on power

— Turn on power to the

ImagePRO-II, your projector(s), and to all
peripheral equipment.

5. Factory reset

— If you are using the

ImagePRO-II for the first time, or if you are using
an ImagePRO-II that has just returned from an
event, perform a full factory reset to restore
default system configurations.

6

.

Obtain the output format

— If the primary

output is connected to an HDMI, DVI-D,
HD-15 or DisplayPort connector, obtain the
output’s preferred resolution and frame rate
using the Output Menu. This is the format the
ImagePRO-II uses. (Chapter 4, “Using EDID
Auto Config” section)

7. Adjust output format

— If the primary output

is connected to the composite video connector
or one the SDI connectors, you can adjust the
output format manually if necessary. (Chapter
4, “Setting Output Format” section)

8. Test output

— Turn on a test pattern, verify

that you have an image, and make any
necessary adjustments. When complete, turn
off the test pattern. (Chapter 4, “Working with
Test Patterns” section)

9. Save output configuration

— After

completing output adjustments, save the
output configuration.

10

.

Position and adjust the image

— Use the

LED Setup Menu

to

position the image on the LED wall or other display device, scale
the image, adjust pan and zoom settings, and save your view.
(Chapter 4, “Positioning an Image on the Display” section.)

11

.

Set and adjust inputs

— Select inputs and make any necessary

adjustments to color balance, timings, and so on. (Chapter 4,
“Configuring Inputs” section.)

12. Save input configuration

— After adjusting an input, save the

input configuration. (Chapter 4, “Saving an Input Configuration”
section.)

13. Adjust and save system settings

— Adjust system parameters

such as VFD brightness, Ethernet settings, and HDCP
parameters. (Chapter 4, “Using the System Menu” section.)

Setting up an LED Display

AC

Connect to AC

power source.

Ethernet

Connect to Web

Interface or

external controller.

Genlock

Connect a

reference signal

such as black

burst or

composite sync.

SDI Input

with Loop-

through

Connect to

SD-SDI or HD-

SDI sources.

DVI-I Input with

Loop-through

Connect to DVI

sources.

Analog Input

with Loop-

through

Connect to

HD-15 sources.

DisplayPort

Input

Connect to

DisplayPort

sources.

HDMI

Input

Connect to

HDMI

sources.

SDI

Output

Connect to

SDI display.

Composite

Output

Connect to NTSC/

PAL composite

video display.

DVI-D Output

Connect to DVI

video display.

HDMI

Output

Connect to

HDMI display.

Analog

Output

Connect to

analog

display.

Phone:

Fax:

Technical Support:

Websites:

+1 (916) 859-2500
+1 (916) 859-2515
+1 (866) 374-7878
www.barco.com
www.events.barco.com

S3D/Dual

Channel Options

Connect to S3D and

dual channel sources,

invert sync signals.

DisplayPort

Output

Connect to

DisplayPort

display.

Audio I/O

Connect to audio

source.