Page 4 - Support
your local authority responsible for waste disposal. Businesses shouldcontact the product supplier for information about how to disposeof this product correctly.This product complies with the requirements of Directive 2011/65/EU onthe restriction of the use of certain hazardous substances in electri...
Page 5 - AXIS M1034-W Network Camera; Safety Information; Hazard Levels; DANGER; Other Message Levels
AXIS M1034-W Network Camera Safety Information Safety Information Hazard Levels DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION Indica...
Page 6 - Table of Contents
AXIS M1034-W Network Camera Table of Contents Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Hazard Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Other Message Levels . . . . . ...
Page 8 - Hardware Overview; Connectors and Buttons
AXIS M1034-W Network Camera Hardware Overview Hardware Overview 1 2 8 9 12 11 10 13 14 15 16 17 4 5 6 7 2 1 3 1 Status LED indicator 2 Focus ring 3 Lens 4 Microphone 5 Speaker 6 PIR sensor 7 Light (white illumination LED) 8 Network connector (RJ-45) 9 Power connector 10 Lock ring11 I/O terminal conn...
Page 9 - Network Connector; Digital output; Power Connector; LED Indicators; Status LED
AXIS M1034-W Network Camera Hardware Overview Network Connector RJ45 Ethernet connector. NO NO NOTICE TICE TICE The product shall be connected using a shielded network cable (STP). All cables connecting the product to the network shallbe intended for their specific use. Make sure that the network de...
Page 11 - Access the Product; Access from a Browser; Access from the Internet
AXIS M1034-W Network Camera Access the Product Access the Product To install the Axis product, see the Installation Guide supplied with the product. The product can be used with most operating systems and browsers. The recommended browsers are • Internet Explorer ® with Windows ® • Safari ® with OS ...
Page 12 - Set the Root Password; Set Power Line Frequency
AXIS M1034-W Network Camera Access the Product For more information, see NAT traversal (port mapping) for IPv4 on page 49 . See also AXIS Internet Dynamic DNS Service at www.axiscam.net For Technical notes on this and other topics, visit the Axis Support web at www.axis.com/techsup Set the Root Pass...
Page 13 - Controls on the Live View Page; Manual Trigger
AXIS M1034-W Network Camera Access the Product Controls on the Live View Page Click View size to scale the image down to 800 pixels wide or to full scale. Only available in MJPEG. Select a stream profile for the Live View page from the Stream Profile drop-down list. For information about how to conf...
Page 14 - AXIS Media Control viewer toolbar; AMC Audio Controls; PTZ Controls
AXIS M1034-W Network Camera Access the Product For more information about action rules, see Events on page 35 . To show the manual trigger buttons in the Live View page: 1. Go to Setup > Live View Config . 2. Under Action Buttons , select Show manual trigger button . AXIS Media Control viewer too...
Page 15 - Emulate joystick mode; Pan and Tilt bars
AXIS M1034-W Network Camera Access the Product Click the Emulate joystick mode button and click in the image to move the camera view in the direction of the mouse pointer. Click the Center mode button and click in the image to center the camera view on that position. The center mode button could als...
Page 16 - Media Streams; MJPEG
AXIS M1034-W Network Camera Media Streams Media Streams The Axis product provides several audio and video stream formats. Your requirements and the properties of your network willdetermine the type you use. The Live View page in the product provides access to H.264 and Motion JPEG video streams, aud...
Page 17 - Settings; Alternative Methods of Accessing the Video Stream; Motion JPEG server push
AXIS M1034-W Network Camera Media Streams The AMC Control Panel can be used to configure various video and audio settings. Please see the AXIS Media Control User’sManual for more information. The AMC Control Panel is automatically installed on first use, after which it can be configured. Open the AM...
Page 18 - Access Audio Streams; VAPIX® Application Programming Interface (API); Java applet
AXIS M1034-W Network Camera Media Streams Note • <ip>= IP addess • The Axis product supports QuickTime 6.5.1 and later. • QuickTime may add latency to the video stream. • It may be possible to use other players to view the H.264 stream using the paths above, although Axis does not guarantee th...
Page 19 - Set Up the Product; Setup; Basic Setup
AXIS M1034-W Network Camera Set Up the Product Set Up the Product The Axis product can be configured by users with administrator or operator rights. To open the product’s Setup pages, click Setup in the top right-hand corner of the Live View page. • Administrators have unrestricted access to all set...
Page 20 - Video and Audio; Set Up Video Streams; Pixel Counter
AXIS M1034-W Network Camera Video and Audio Video and Audio The video and audio settings can be used to optimize video and audio quality. You can configure the following: • Video stream settings. See page 20 . • Stream profiles. See page 21 . • Camera settings. See page 22 . • View area. See page 22...
Page 21 - Stream Profiles
AXIS M1034-W Network Camera Video and Audio • Maximum frame rate . To avoid bandwidth problems, the frame rate allowed to each viewer can be Limited to a fixed amount. Alternatively, the frame rate can be set as Unlimited , which means the Axis product always delivers the highest frame rate possible...
Page 22 - Camera Settings; Image Appearance; View Area
AXIS M1034-W Network Camera Video and Audio For quick setup, use one of the predefined stream profiles. Each predefined profile has a descriptive name, indicating its purpose. Ifrequired, the predefined stream profiles can be modified and new customized stream profiles can be created. To create a ne...
Page 23 - Overlay; Overlay Image
AXIS M1034-W Network Camera Video and Audio 2. Select an Aspect ratio and a Video stream resolution . 3. Use the mouse to move and resize the view area. 4. Select Enable PTZ to enable digital PTZ for the view area. 5. Click Save to save the settings. Note The PTZ functionality is useful during insta...
Page 25 - Privacy Mask; Audio Modes; Audio Input
AXIS M1034-W Network Camera Video and Audio ExampleTo display the text “Motion detected” when motion is detected, enter #D in the Include text field and enter “Motion detected” in the Text field when setting up the action rule. Privacy Mask A privacy mask is a user-defined area that prevent users fr...
Page 26 - Audio Output; Audio Clips
AXIS M1034-W Network Camera Video and Audio Use the Encoding option to select digital audio encoding format. • AAC requires a license for both encoding and decoding. AAC is the least complicated and most widely used codec. If achieving the best possible audio quality is a priority, AAC is the recomm...
Page 27 - Configure the Live View Page; Default Viewer for Browsers
AXIS M1034-W Network Camera Configure the Live View Page Configure the Live View Page You can customize the Live View page and alter it to suit your requirements. It is possible to define the following features ofthe Live View page. • Stream Profile. See page 21 . • Default Viewer for Browser. See p...
Page 28 - User Defined Links
AXIS M1034-W Network Camera Configure the Live View Page • Select Use PTZ joystick mode as default to enable joystick mode. The mode can be changed temporarily from the PTZ control panel. • Select Enable recording button to enable recording from the Live View page. This button is available when usin...
Page 29 - Access the Preset Positions; Set the Home Position; Guard Tour
AXIS M1034-W Network Camera PTZ (Pan Tilt Zoom) PTZ (Pan Tilt Zoom) The PTZ menu is available if digital PTZ (pan, tilt and zoom) is enabled in the selected view area. For more information on view areas,see View Area on page 22 . Preset Positions A preset position is a saved view that can be used to...
Page 30 - Advanced; Controls; Control Queue
AXIS M1034-W Network Camera PTZ (Pan Tilt Zoom) 4. Select an available preset position and click Apply . 5. Specify the View Time in seconds or minutes. 6. Specify the View Order or select the Random view order option. 7. Click Save . To modify or remove guard tours, go to PTZ > Guard Tour , sele...
Page 31 - Viewer
AXIS M1034-W Network Camera PTZ (Pan Tilt Zoom) 5. Viewer — Multiple viewers must wait for their turn. The viewer has 60 seconds PTZ control before control is passed on to the next viewer in queue. 31
Page 32 - Detectors; Camera Tampering; Motion Detection
AXIS M1034-W Network Camera Detectors Detectors Camera Tampering Camera Tampering can generate an alarm whenever the camera is repositioned, or when the lens is covered, sprayed or severelydefocused. To send an alarm, for example an email, an action rule must be set up. To configure tampering: 1. Go...
Page 33 - Set Up Motion Detection Windows; Motion Detection Parameters
AXIS M1034-W Network Camera Detectors Note • Using the motion detection feature may decrease the product’s overall performance. • The position of the Motion Detection Window is relative to the orientation of the Camera. Changing the orientation of the camera will also change the position of the Moti...
Page 34 - Audio Detection; PIR Sensor
AXIS M1034-W Network Camera Detectors Note • To trigger on small objects or movements, use several small motion detection windows rather than one large window and select a low object size. • To avoid triggering on small objects, select a high object size. • While monitoring an area where moving obje...
Page 35 - Events; Convert Event Types to Action Rules; Set Up Action Rules
AXIS M1034-W Network Camera Events Events The Event pages allow you to configure the Axis product to perform actions when different events occur. For example, the productcan start a recording or send an email notification when motion is detected. The set of conditions that defines how and whenthe ac...
Page 36 - Triggers
AXIS M1034-W Network Camera Events For more information, see the online help . Triggers Available action rule triggers and conditions include: • Detectors - Audio Detection – Trigger the rule when audio is detected. See Audio Detection on page 34 . - Live Stream Accessed – Trigger the rule when any ...
Page 37 - Actions; Add Recipients; Recipient Types
AXIS M1034-W Network Camera Events - System Ready – Trigger the rule when the product has been started and all services are running. This can for example be used to send a notification when the product restarts. • Time - Recurrence – Trigger the rule periodically. See Set Up Recurrences on page 39 ....
Page 38 - Set Up Email Recipients
AXIS M1034-W Network Camera Events Recipient Use with action Notes Email Send Images Send Notification Send Video Clip An email recipient can contain multiple email addresses. FTP Send Images Send Video Clip HTTP Send Images Send Notification Send Video Clip HTTPS Send Images Send Notification Send ...
Page 39 - Create Schedules
AXIS M1034-W Network Camera Events Create Schedules Schedules can be used as action rule triggers or as additional conditions, for example to record video if motion is detected outsideoffice hours. Use one of the predefined schedules or create a new schedule as described below. To create a new sched...
Page 40 - Recordings; Recording List
AXIS M1034-W Network Camera Recordings Recordings The Axis product can be configured to record video continuously or according to an action rule: • To start a continuous recording, see page 40 . • To set up action rules, see page 35 . • To access recordings, see Recording List on page 40 . • To conf...
Page 41 - Save
AXIS M1034-W Network Camera Recordings 5. Click Save to save and start the recording. 41
Page 42 - Languages; Upload Language; Restore
AXIS M1034-W Network Camera Languages Languages Multiple languages can be installed in the Axis product. All web pages including the online help will be displayed in the selectedlanguage. To switch languages, go to Setup > Languages and first upload the new language file. Browse and locate the fi...
Page 43 - System Options; Security; Users
AXIS M1034-W Network Camera System Options System Options Security Users User access control is enabled by default and can be configured under System Options > Security > Users . An administrator can set up other users by giving them user names and passwords. It is also possible to allow anony...
Page 44 - Certificates
AXIS M1034-W Network Camera System Options 2. Select an HTTPS certificate from the list of installed certificates. 3. Optionally, click Ciphers and select the encryption algorithms to use for SSL. 4. Set the HTTPS Connection Policy for the different user groups. 5. Click Save to enable the settings....
Page 45 - Audio Support
AXIS M1034-W Network Camera System Options A Server/Client certificate can be self-signed or issued by a Certificate Authority (CA). A self-signed certificate offers limited protection and can be used before a CA-issued certificate has been obtained. To install a self-signed certificate: 1. Go to Se...
Page 46 - Network; Basic TCP/IP Settings; Network Interface Mode; Enable ARP/Ping setting of IP address
AXIS M1034-W Network Camera System Options Network Basic TCP/IP Settings The Axis product supports IP version 4 and IP version 6. Both versions can be enabled simultaneously, and at least one versionmust always be enabled. Network Interface Mode The network interface to the AXIS product can be wired...
Page 47 - AXIS Internet Dynamic DNS Service
AXIS M1034-W Network Camera System Options arp -s 192.168.0.125 00:40:8c:18:10:00 tempping -s 408 192.168.0.125 Windows syntax (this may require that you run the command prompt as an administrator) arp -s <IP address> <serial number>ping -l 408 -t <IP address> Windows example (this...
Page 48 - Advanced TCP/IP Settings
AXIS M1034-W Network Camera System Options Advanced TCP/IP Settings DNS Configuration DNS (Domain Name Service) provides the translation of host names to IP addresses. The DNS settings are configured under System Options > Network > TCP/IP > Advanced . Select Obtain DNS server address via D...
Page 49 - NAT traversal; Use manually selected NAT router -; Wireless; Wireless Network Status
AXIS M1034-W Network Camera System Options NAT traversal (port mapping) for IPv4 A network router allows devices on a private network (LAN) to share a single connection to the Internet. This is done by forwardingnetwork traffic from the private network to the “outside”, that is, the Internet. Securi...
Page 50 - Wireless Settings
AXIS M1034-W Network Camera System Options • Mode shows the type of network, which can be Master (an access point) or Ad-Hoc . • Security shows the type of security the network uses. • Channel shows the wireless channel currently in use. • Signal strength shows the quality, the strength, of the sign...
Page 51 - WPA
AXIS M1034-W Network Camera System Options If applicable, select the Network type . Select Master to access the network via an access point or Ad-hoc to access any other wireless device and create a local network. Ad-hoc mode allows users to form a wireless LAN without connection through an access p...
Page 52 - WEP; No Security
AXIS M1034-W Network Camera System Options Important To ensure successful certificate validation, time synchronization should be performed on all clients and servers prior toconfiguration. To configure the wireless settings using the WPA TM -/WPA-Enterprise security method and EAP-PEAP/MSCHAPv2: 1. ...
Page 53 - SOCKS
AXIS M1034-W Network Camera System Options gain access to the protected wireless network, the Axis product presents its certificate to the network switch. If the certificate isapproved, the switch allows access. You may need to contact your network administrator for information on certificates, user...
Page 54 - Enable traps; UPnP; Always Multicast Video; Bonjour; SD Card
AXIS M1034-W Network Camera System Options Note If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled. Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap m...
Page 55 - Mount and Unmount SD Card
AXIS M1034-W Network Camera System Options Note Do not insert or eject the SD card while the product is running. The product will lose its connection to the wireless network.Reboot the product to reestablish the wireless connection after the card has been inserted or ejected. The following SD card f...
Page 56 - Network Share; Port Status; Maintenance
AXIS M1034-W Network Camera System Options Network Share Network share allows you to add network storage such as a NAS (network-attached storage). The NAS shall be dedicated forrecordings and data from the Axis products connected to the network. For information about reference NAS devices, go to www...
Page 57 - Default; Flash LED; Support Overview; System Options > Support > Support Overview; System Overview; System Options > Support > System Overview
AXIS M1034-W Network Camera System Options • the default router • the subnet mask • the system time • the IEEE 802.1X settings • the wireless settings Click Default to reset all settings, including the IP address, to the factory default values. This button should be used with caution. The Axis produ...
Page 58 - Scripting; File Upload; Reset to Factory Default Settings
AXIS M1034-W Network Camera System Options Advanced Scripting Scripting allows experienced users to customize and use their own scripts. NO NO NOTICE TICE TICE Improper use may cause unexpected behavior and loss of contact with the Axis product. Axis strongly recommends that you do not use this func...
Page 59 - Troubleshooting; Check the Firmware; Emergency Recovery Procedure
AXIS M1034-W Network Camera Troubleshooting Troubleshooting Check the Firmware Firmware is software that determines the functionality of network devices. One of your first actions when troubleshooting a problemshould be to check the current firmware version. The latest version may contain a correcti...
Page 60 - Symptoms, Possible Causes and Remedial Actions; Problems setting the IP address; The product cannot be accessed from a browser; The product is accessible locally but not externally; Basic
AXIS M1034-W Network Camera Troubleshooting 5. Reinstall the product, referring to the Installation Guide. If the emergency recovery procedure does not get the product up and running again, contact Axis support at www.axis.com/techsup/ Note The emergency recovery procedure only works on the wired in...
Page 63 - Technical Specifications
AXIS M1034-W Network Camera Technical Specifications Technical Specifications Function/group Item Specifications Model AXIS M1034-W Image sensor 1/4" Progressive scan RGB CMOS Lens 2.8 mm, F2.0 fixed irisHorizontal angle of view: 80°Vertical angle of view: 51° Minimumillumination 1.2 - 100000 lu...
Page 65 - Connectors
AXIS M1034-W Network Camera Technical Specifications Function/group Item Specifications Casing Color: White NCS S 1002-BPolycarbonate Memory 256 MB RAM, 128 MB Flash Power 4.9–5.1 V DC, max. 6.5 W Connectors DC jackRJ45 10BASE-T/100BASE-TXTerminal blocks with power output, 1 alarm input and 1 output...
Page 66 - Function; Connection Diagrams; Performance Considerations
AXIS M1034-W Network Camera Technical Specifications Function Pin Notes Specifications 0 V DC (-) 1 0 V DC DC output 2 Can be used to power auxiliary equipment.Note: This pin can only be used as power out. 3.3 V DCMax load = 50 mA Digital input 3 Connect to pin 1 to activate, or leave floating (unco...
