Autostart CT-3200 - Manual

Autostart CT-3200

Autostart CT-3200 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
Page: / 21

Table of Contents:

  • Page 2 – Before You Get; never
  • Page 3 – only when the hood is up.; always solder and tape all connections.; Multiple or separate door pin connections:; clicks”; Wire; CRANK
  • Page 4 – -Pin Secondary Harness
  • Page 5 – 2-Pin Accessories Harness; Note; Option 1 connects to negative trunk pin.
  • Page 6 – WHITE; ΙΙ; YELLOW
  • Page 7 – Flashing the Hood Pin; any time the hood is up.
  • Page 8 – OFF; Table 1; How to Enter Programming Options Mode; Table 2
  • Page 9 – Programming Options; autotach
  • Page 10 – Table 4; Multi-Speed Tach Programming; Table 5; Testing
  • Page 11 – Cautio; Ignition-controlled Door Locks; arm; START
  • Page 12 – Table 6; hot wire; Table 7
  • Page 15 – A basic introduction to the Relay:
  • Page 16 – either; 6, and then Ground the OTHER terminal to; A closer look at a relay:; Powering a second Ignition
  • Page 17 – The relay connections:
  • Page 19 – LOCK
Loading the manual

Please note:

Button

Ι

is for the

LOCK/UNLOCK

functions.

Button

ΙΙ

is for the

START/STOP

functions.

Buttons

Ι

&

ΙΙ

(together) is for the

TRUNK

release function.

The LED is NOT included in this model.

Notice

The manufacturer will accept no responsibility for any electrical damage resulting from improper
installation of the product, be that either damage to the vehicle itself or to the Unit. This Unit must
be installed by a certified technician using all safety devices supplied. Please note that this guide
has been written for properly trained Autostart technicians, a certain level of skill and knowledge is
therefore assumed. Please review the Installation Guide carefully before beginning any work.

Warning

This Unit is designed for vehicles with an

automatic

Transmission only. Before installing the

Unit, test that the vehicle does not start when the gear select lever is in the “Drive” position. If it
starts in gear, install a manual-transmission car starter instead.

DOC.1.50

CA –

September 2, 2004

Manufactured in Canada by Autostart

A U T O M A T I C

T R A N S M I S S I O N M U L T I -

C H A N N E L R E M O T E S T A R T E R S Y S T E M

CT-3200

Installation Guide

Table of Contents

Introduction ...................................................2

Included in the Package ...............................2

Installation Tools:..........................................2

Before You Get

Started

… ........................2

Harness Description .....................................3

6-Pin Main Ignition Harness.....................3

5-Pin Secondary Harness........................4

12-Pin Accessories Harness....................5

Flashing the Hood Pin ..................................7

The Programming Assistance Button (a.k.a.
PAB.) ............................................................8

Before Programming a Transmitter ..............8

How to Program the Transmitter. .................8

How to Enter Programming Options Mode...8

Programming Options...................................9

Auto Tach Programming Procedure .............9

Multi-Speed Tach Programming .................10

Testing ........................................................10

Closing Up ..................................................11

Supplementary Information ........................11

Fifth Relay Output (2nd Ignition or 2nd
Accessories or 2nd Crank Output) .............11

Ignition-controlled Door Locks ...............11

Secure Lock...........................................11

Passive or Active Arming Starter Kill .....12

Lock Pulse Duration ..............................12

Engine Run Time ...................................12

Idle Mode ...............................................12

Resetting the Module (without the plug-in
valet) ...........................................................12

Resetting the Module (with the use of the
plug-in valet) ...............................................12

Troubleshooting Poor Transmitting Range 13

Installation Order ........................................13

A basic introduction to the Relay:...............15

Troubleshooting Poor Transmitting Range 19

Trouble shooting Q & A ..............................19

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Before You Get; never

P. 2 Installation Guide CT-3200 Introduction This guidebook contains all information pertinent to the installation. Most (if not all) features are grouped in the user guidebook and therefore, should you need information on a feature, you should refer to the user guidebook. Included in the Package Be...

Page 3 - only when the hood is up.; always solder and tape all connections.; Multiple or separate door pin connections:; clicks”; Wire; CRANK

CT-3200 Installation Guide P. 3 order to avoid having to get out of the vehicle and pressing the hood-pin switch. The PAB will work only when the hood is up. ♦ inspect vehicle for any body damage or electrical problems ♦ always solder and tape all connections. ♦ keep the transceiver away from other ...

Page 4 - -Pin Secondary Harness

P. 4 Installation Guide CT-3200 C RED (+) 12 V Battery Connect to the largest 12 V supply wire at the ignition harness. Ensure that the OEM power wire is fused for more than 30 A. NOTE: certain new vehicles have no suitable 12 volts source at the IGNITION switch (the 12 Volt wire is too small to sup...

Other Autostart Models

All Autostart Other