Autostart AS-3372 TW-FM - Manual

User Guide P. 11 module's Trunk release output activates the relay. The ground signal is sent from 87 through 30 to the vehicle's Trunk release wire activating the switch and opening the trunk. Harness Description 6-pin Main Ignition Harness (a.k.a. The Primary harness) The two Red wires are the pow...

P. 12 User Guide 5-pin Secondary Harness (a.k.a. the secondary harness) This harness has the remaining wires used in basic remote starter installations, positive parking light output, the safety shut down inputs, and the ground wire for the module. Wire Description 1 BLACK (–) Chassis ground input T...

P. 14 User Guide vehicles is to pre-heat the Combustion Chamber before the vehicle is started. When a Remote Starter is installed on a diesel vehicle, the Glow- plug section of the Ignition circuit must be activated and allowed to operate before the vehicle is remote-started. For that purpose, the G...

User Guide P. 15 5 Pager Port Is used to connect an optional AS-200P pager (to use this option, make sure to program pager option in Menu 3, Feature 5, Option 4 ). Entering Programming Mode This allows the installer to program the unit. Once the system is in programming mode, the installer will have...

User Guide P. 17 START/STOP ...................to access menu 4. 3. The parking lights will flash and the horn will honk (if programmed) once, twice, three or four times to confirm entry into a menu. 4. Release the brake pedal. Once the desired menu has been selected, the unit will fall (by default)...

P. 18 User Guide MENU 3 * indicates default setting FEATURE 1 – Home Valet OPTION 1 Home Valet ENABLED OPTION 2* Home Valet DISABLED FEATURE 2 – AUX 1 Programming OPTION 1 Horn confirmation upon the 2 nd press of the LOCK button OPTION 2* Priority door access OPTION 3 Horn confirmation upon the 1 st...

User Guide P. 19 3. Press the LOCK button if you wish to increase the time delay or the UNLOCK button if you want to decrease it. The time delay will be increased or decreased by 50ms. and the parking lights will flash once every time the LOCK or UNLOCK button is pressed. 4. Press the TRUNK button t...

P. 20 User Guide Clutch Bypass In order to remote start a manual transmission vehicle, the clutch switch must be bypassed. Clutch safety switch circuits can take many forms. Listed below are the most common ones. Some vehicles may also have a separate or combined switch on the clutch pedal for cruis...

User Guide P. 21 modules connected to the G.O. Wire, a relay (and diodes) may have to be added to strengthen the negative current going to the clutch bypass. Positive: Very similar to the negative system, except that the vehicle's clutch relay is triggered by 12 volts instead of a negative signal. I...

User Guide P. 23 Flashing LED To gain access to this feature, make sure the Flashing LED option has been enabled at the time of programming. Once this option is enabled, the user has the choice to toggle the Flashing LED ON and OFF at any given moment. To toggle between the Flashing LED ON and OFF ,...

User Guide P. 25 • Start the engine by remote. • Turn the ignition key to the IGNITION ON (RUN) position. • Press and release the AUX button. The LOCK button on the transmitter will light up. While the LOCK button is still lit up, press the START/STOP button. The transmitter will beep once. Keep pre...

P. 26 User Guide successively into the IGNITION/RUN and OFF positions. The parking lights will flash twice. b. Turn the ignition OFF The LED on the antenna will flash quickly to indicate that the vehicle is now out of Valet mode. • To put the system o u t o f Valet mode using the TRANSMITTER (Remote...

User Guide P. 27 c) By turning the key to the ON position and pressing the valet switch (if included) until the parking lights flash 5 times. Panic Mode will automatically shut down after 30 sec. The AUX 1 / 2 nd Unlock (Both AUX 1 and AUX 2 can be programmed for Priority Door Access.) This great fe...

Installation Guide P. 29 OEM-Style Alarm The OEM-style alarm (if configured) monitors the doors, hood and ignition switch of the vehicle. It will sound the horn if a door or the hood is opened, or if the key is turned in the ignition ( the horn option must be enabled and one of the door inputs must ...

P. 30 Installation Guide Vehicle Status Request The status request feature allows the user to see the status of the vehicle  i.e.: if the doors are locked or unlocked or if the vehicle is in cold weather mode, home valet mode, valet mode or how much time is left in the run time cycle. The following...

Installation Guide P. 31 STATUS SEQUENCE LED #1 LED #2 LED #3 LED #4 Beep(s) 1 st sequence if unlocked X 3 flashes X X 2 2 nd sequence X X X 4 4 Table 2 Status Request When the Engine is Running When the vehicle doors are locked: The LED # 1 will flash 3 times to denote that the vehicle’s doors are ...

P. 32 Installation Guide Horn Honk Timing Follow these steps to program horn confirmation: 1. Enter programming mode (see on page 15)  the parking lights will stay on for up to 20 seconds 2. Press and hold the brake pedal, then simultaneously press the UNLOCK and START/STOP buttons  the horn will ...

Installation Guide P. 33 ‰ Hood switch shutdown. With the vehicle running under the remote car starter, open the hood; the vehicle should shut down. If it does not shut down, check the hood pin-switch and its connector. ‰ Brakes shutdown circuit. With the vehicle running under the remote car starter...

P. 34 Installation Guide Diagnostics – Parking Light Flash Table Flashes Description 1 • Doors locked, starter kill armed. • Run time has expired. • TRUNK button pressed. • Start signal received by the module. • Cold weather mode cancelled. 2 • Doors unlocked, starter kill disarmed. • Remote start a...

Installation Guide P. 35 Troubleshooting Q & A The following are some common installation-related issues. A problem or symptom is given and then possible solutions and/or suggestions as to areas to verify are enumerated. 1. I cannot program the remote control. • Do the parking lights come on whe...