Audiovox PRO-9642CH - Manual
Audiovox PRO-9642CH – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALLATION OF MAJOR COMPONENTS
- Page 3 – WIRING THE SYSTEM; Large 15 Pin Edge Connector:; some remote start trigger inputs will damage the control module.
- Page 7 – COMPLETING THE INSTALLATION; Adjusting the Optional Shock Sensor :; Using a small screwdriver, gently turn the adjustment screw fully
128-6623
1 of 8
Model PRO-9642CH
Installation Manual
Note : When both Passive Arming and Voltage Sensing are selected, you must hardwire the driver’s door pin switch in order to
begin the passive arming sequence.
RF Programmable Features :
Feature Selection
1 Chirp
2 Chirps
3 Chirps
4 Chirps
Default
1st Door L/UL
1 Sec.
3.5 Sec.
1 Sec L, Dbl. U/L
1 Sec.
2nd Accy Lock
Auto Lock On
Auto Lock Off
Auto Lock Off
3rd Accy. UL
Auto UL Dr.
Auto UL All
Auto UL Off
Auto UL Off
4th Passive Locks
Passive
Active
Active
5th Passive/Active Arm
Passive Arm
Active Arm
Active Arm
6th Voltage Sense
Voltage Sense
Hardwire
Hardwire
7th Siren/Horn
Siren/Horn
Siren Only
Horn Only
Siren/Horn
8th Horn Chirp
10mS
16mS
30mS
16mS
9th Override Method
Custom Code
Valet
Valet
10th Two Step Unlock
On
O f f
O f f
11th Chirp Delete From Tx
On
O f f
O f f
To program these selectable features;
Action
System Response
Turn ignition on
No response
Press and release the valet switch 3 times
1 Chirp - LED 1 flash
Within 3 seconds, turn ignition Off
Short chirp, then long chirp
First
Then On
1 chirp = 1 second door locks
Press transmitter Lock button to change
2 chirps = 3.5 second door locks
Press transmitter Lock button to change
3 chirps = 1 sec. lock, dbl 1 sec. unlock
o r
Second
Press and release the valet switch
2 chirps = auto locks off
Press transmitter Lock button to change
1 chirp = auto locks on
o r
Third
Press and release the valet switch
3 chirps = auto unlock off
Press transmitter Lock button to change
1 chirp = auto unlock dr.
Press transmitter Lock button to change
2 chirps = auto unlock all
o r
Fourth
Press and release the valet switch
2 chirps = active locks
Press transmitter Lock button to change
1 chirp = passive locks
o r
Fifth
Press and release the valet switch
2 chirps = active arming
Press transmitter Lock button to change
1 chirp = passive arming
o r
Sixth
Press and release the valet switch
2 chirps = hardwire
Press transmitter Lock button to change
1 chirp = voltage sense
o r
Seventh
Press and release the valet switch
1 chirp = siren and horn output
Press transmitter Lock button to change
2 chirps = siren output only
Press transmitter lock button to change
3 chirps = horn output only
Sixth
Press and release the valet switch
2 chirps = hardwire
Press transmitter Lock button to change
1 chirp = voltage sense
o r
Seventh
Press and release the valet switch
1 chirp = siren and horn output
Press transmitter Lock button to change
2 chirps = siren output only
Press transmitter lock button to change
3 chirps = horn output only
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
128-6623 2 of 8 Page 2 o r Eight Press and release the valet switch 2 chirps = horn chirp output 16mS Press transmitter Lock button to change 3 chirps = horn chirp output 30mS Press transmitter Lock button to change 1 chirp = horn chirp output 10 mS o r Ninth Press and release the valet switch 2 chi...
128-6623 3 of 8 Page 3 Valet Switch:Select a mounting location for the switch that is easily accessible to the driver of the vehicle. The switch doesnot have to be concealed, however, concealing the switch is always recommended, as this provides an evenhigher level of security to the vehicle.The val...
128-6623 7 of 8 Page 7 door lock/unlock motor legs rest at ground, and switch +12 volts to the door lock/unlock motor legs for opera-tion, if this is the case in the vehicle you are working on, connect the remaining terminal, 87, to a fused + 12 voltsource. In the rare instance that the vehicle door...
