Audiovox PRO 9233 - Manual
Audiovox PRO 9233 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – PROTECTION WHILE THE SYSTEM IS ARMED :; vehicle will not start.; DISARMING THE SYSTEM :
- Page 3 – INTRUSION WARNING SIGNALS :; intrusion attempt was made through one of the vehicle’s doors.; OPERATING THE EMERGENCY PANIC:; release the unlock button on your keychain transmitter.; USING THE VALET SWITCH :
- Page 4 – TO ENTER THE VALET MODE:; turns on, indicating valet mode has been successfully entered.; MANUAL OVERRIDE OPERATION:; sound, turn the ignition switch to the “on” position.
- Page 5 – Programming Your Custom Override Code:; sequence. Turn the ignition switch to the on position.
- Page 6 – Custom Code Programming Example:; (The siren or horn will beep and the lights will flash one time.); ADDITIONAL REMOTE FUNCTION :
- Page 8 – SYSTEM FUNCTIONS AT A GLANCE; CHIRP INDICATORS; Your System Has These Features Activated:
128-7777
1 of 8
1
Congratulations on your purchase of the PRO9233 automotive Keyless Entry
Upgrade Alarm System. This system is a state - of - the - art auto security system
that is designed to automatically arm and disarm when it receives a command from
your existing Factory Keyless Entry Transmitter. Taking a few moments to read this
manual will help to ensure that your vehicle is protected at all times.
NOTE:
The system has the ability to beep the vehicle's horn, sound a siren, or both. Where
a beep or chirp is mentioned, consider either or both may sound.
ARMING THE SYSTEM : ( ACTIVE )
1. Turn the ignition key off, exit the vehicle, and close all doors.
2. Press and release the Lock button on the keychain transmitter.
3. The siren and or horn will beep one time, the parking lamps will flash one time,
and the red dash mounted LED will begin to slowly flash, indicating that the
system is ARMED.
If the siren/horn
sounds 3 chirps, then you have left a door, trunk, or hood lid ajar.
Simply close the opened entry point to provide full protection. If the siren "chirped"
three times, sometime after arming, the exclusive delayed dome light learn circuit
has been programmed and the system detected a open entry point after the
learned delay expired. Again, closing the hood, trunk, or doors will correct the
problem and you do not need to disarm the system to make the correction. If the
siren/horn did not sound when arming, then the chirps have been turned off, and
you should refer to the section titled “ ELIMINATING THE ARM / DISARM CHIRPS “
in this manual.
4. Any time the door lock switch in the vehicle is used to lock the doors while
the ignition key is turned off, the system will immediately arm. To lock the doors
after entering the vehicle, make sure the ignition key is switched on first.
Turning the ignition key on first will stop the system from arming.
ARMING THE SYSTEM : ( PASSIVE )
1. Turn the ignition key off, exit the vehicle, and close all doors.
2. The dash mounted LED will begin to flash rapidly, indicating that the system
Model PRO 9233
OWNER’S MANUAL
KEYLESS ENTRY ALARM UPGRADE MODULE
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
128-7777 2 of 8 2 is automatically ( passively ) arming. As an added convenience, the 30 secondautomatic passive arming will not begin until all doors are closed, allowing passen-gers to exit the vehicle at their convenience.3. In 30 seconds, you will hear a single short chip from the siren, and the...
128-7777 3 of 8 3 installed, the vehicle’s interior lights will turn on for 30 seconds, or until theignition key is turned on. NOTE: If your system has been programmed for “ passive arming “, then it will begin to re-arm immediately after disarming. This is indicated by arapid flashing of the red da...
128-7777 4 of 8 4 TO ENTER THE VALET MODE: 1. Disarm the unit by use of the factory transmitter or by use of the manual override sequence. 2. Turn the ignition switch to the “On” position.3. Press and hold the valet/override pushbutton switch for 5 seconds. The LED turns on, indicating valet mode ha...
