Audiovox PRO-9056 - Manual
Audiovox PRO-9056 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – To program these selectable features
- Page 5 – INSTALLATION OF THE MAJOR COMPONENTS:; PUSH-BUTTON LED SWITCH; This system is to be used in vehicles with; AUTOMATIC TRANSMISSIONS; only! Although this combination Keyless; IT MUST NOT; be installed into a
- Page 6 – WIRING THE 6 PIN MAIN POWER HARNESS:; Do not remove the fuse holders from this wire harness. Fuses must be; Trace Wire: + 12 volts Battery 1 Source; Starter Output
- Page 7 – SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS.; Ignition 1 Output
- Page 8 – Accessory Output; WIRING CONNECTIONS: 12 Pin Input / Output Harness; Chassis Ground Source
- Page 9 – Brake Switch Positive Shutdown Detail; Ignition 3 / Shock Disable Output
- Page 10 – General Motors VATS By-Pass Diagram; Tach Sensor Input
- Page 11 – Tachometer Input Wiring Detail; Diesel Wait To Start Input; WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS; Pulsed Ground Output Before Start; Push-Button LED Programming Switch Assembly:
- Page 13 – cylinder, four coil systems, connect to any of the three coils.
- Page 14 – switch off. DO NOT attempt to remove the key.; REMEMBER TO RECONNECT THE BROWN/BLACK WIRE TEMPORARILY; KEY IN SENSOR CIRCUITS:
- Page 15 – METHOD 1; METHOD 2
- Page 16 – Pin Upgrade Data Bus/Flash Logic Module:; COMPLETING THE INSTALLATION:; to clean the surface before affixing the label.
- Page 18 – THIS PAGE LEFT BLANK INTENTIONALLY
128-7762
1 of 19
The selectable features can be set manually as explained below, or with the RF feature programmer.
To set features using the RF programmer, follow the instructions packaged with the programmer.
Factory default settings are indicated by bold text.
Note :
The method of manual override can either be selected to operate from the valet switch or operate as custom code.
Be certain to place a check mark indicating the method used in the box located on the last page of the owner's manual.
NOTE: Keyless Entry Models with no horn output will Flash the Parking Lights instead of chirp where chirp is indicated.
Also, No data will be indicated if a feature is not available for a particular model. The unit will enter the feature but no selection will be available.
RF Programmable Feature Bank 1 Is For Transmitter Programming See Transmitter Programming Guide.
RF Programmable Features Bank 2 Is Alarm Selectable Features:
Feature Selection
1 Chirp
2 Chirps
3 Chirps
4 Chirps
5 Chirps
6 Chirps
1st DoorL/UL
1 Sec.
3.5 Sec.
1 Sec L, Dbl. U/L
Dbl L, 1 Sec UL
Dbl L, Dbl UL
1 S l/350mS ul
2nd Accy Lock
Not Available
3rd Accy. UL
Not Available
4th Headlights
Not Available
5th Passive Locks
Not Available
6th Pass/Act Arm
Not Available
7th Siren/Horn
Not Available
8th Horn Chirp
Not Available
9th O/R Method
Not Available
10th 2 Step U/L
Not Available
11th Chp Del Tx
Not Available
12th Voltage/Hd Wire
Not Available
13th Trigger Circuits
Not Available
14th Lock/Unlock Poll
Not Available
15th Aux Ch 5 Sel
Not Available
16th Aux Ch 6 Sel
Not Available
17th Aux Ch 7 Sel
Not Available
18th Trigger Delay
Not Available
When using the RF programmer, enter the program mode as follows:
Turn the ignition on
Press and release valet switch 3 times
turn ignition off then on
Press and hold valet switch for 5 seconds
Siren and or lights chirp/flash 2 times indicating access to RF feature program mode.
Model PRO-9056
Installation Manual
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
128-7762 2 of 19 To program these selectable features; Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off Then On Short chirp, then long chirp This Action Accesses Feature Bank 2 Alarm Selectable Fe...
128-7762 5 of 19 This Remote Start System is designed for use with Automatic Transmission Vehicles Only! The unit provideswait to start input for glow plug pre-heat which will be used for all diesel applications. If this wire is notconnected, then the unit will remain in the Gasoline mode setting, w...
128-7762 6 of 19 I M P O R T A N T ! DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MULTI PIN INPUT / OUTPUT HARNESS INTO THECONTROL MODULE UNTIL ALL CONNECTIONS TO THE VEHICLE HAVE BEEN MADE. AFTER SELECTINGYOUR TARGET WIRES AS DEFINED BELOW, DISCONNECT THE NEGATIVE BATTERY CABLE FROM THE VE-HIC...
