Audiovox MM801 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
1
2
3
4
5
6
7
8
9
10
11
12
Table of Contents:
Page 2 – Installation Guide; Important Notice
Page 3 – MATERIALS INCLUDED IN THIS PACKAGE:; – 7 pcs
Page 4 – GENERAL INSTALLATION APPROACH:; their respective locations.
Page 5 – The headliner may need to be trimmed.
Page 6 – TRIM RING INSTALLATION:; Cut the trim ring using a Dremel Tool.
Page 7 – MOUNTING THE TRIM RING
Page 8 – on the main PCB and into the Mini-Din Connector on the main PCB.
Page 9 – Positive Switched Dome lighting; CONNECTING THE DOME LIGHTS
Page 10 – No power at Video Monitor; Negative Switched Dome lighting
Page 11 – This Page Intentionally Left Blank
Loading the manual
Installation Guide
1
MM801
8.4" LCD OVERHEAD MONITOR
Installation Guide
P O WE R
M EN U/
E NT E R
ON OFF A UTO
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Page 2 - Installation Guide; Important Notice
Installation Guide 2 Important Notice An LCD panel and/or video monitor may be installed in a motor vehicle and visible to thedriver if the LCD panel or video monitor is used for vehicle information, system control,rear or side observation or navigation. If the LCD panel or video monitor is used for...
Page 3 - MATERIALS INCLUDED IN THIS PACKAGE:; – 7 pcs
Installation Guide 3 MATERIALS INCLUDED IN THIS PACKAGE: 1) MM801 Video Monitor (P/N 136D3649) – 1pc 2) Trim Ring (P/N 102C4007) – 1pc 3) Remote Control (P/N : 136B3650) – 1pc 4) Hardware Package:- ♦ #4 x 5/16” Screws – 7 pcs ♦ #8 x 5/8” Self Drilling Screws – 4 pcs ♦ #8 Washers – 4 pcs 5) 2 Pin Pow...
Page 4 - GENERAL INSTALLATION APPROACH:; their respective locations.
Installation Guide 4 GENERAL INSTALLATION APPROACH: 1) Decide upon system configuration and options that will be installed (i.e.: what components, VCP, Tuner, RF Modulator/external amp, remote headphones, DVD, etc.). 2) Review all manuals to become familiar with electrical requirements and hook ups....
Page 5 - The headliner may need to be trimmed.
Installation Guide 5 VEHICLE PREPARATION: 1) Locate an accessory power source (+12v when key is in the ACC. and run positions, and 0v when key is off). Also locate a good ground wire. Generally, these wires can be found at the ignition switch orfuse-box. 2) The mounting method and location will vary...
Page 6 - TRIM RING INSTALLATION:; Cut the trim ring using a Dremel Tool.
Installation Guide 6 TRIM RING INSTALLATION: This page only covers special installation considerations for the trim ring installation.If the video monitor is to be installed in a vehicle with the trim ring, it may need to be trimmed to fit thecontour of the vehicle headliner. 1) In this installation...
Page 7 - MOUNTING THE TRIM RING
Installation Guide 7 Roof Roof Support Headliner 5"x9"x3/4" PlywoodBlock (4) #8x1" self drilling screws Trim Ring Video Unit (4) #8 flat washers (4) #8x3/4" self tapping screws MOUNTING THE TRIM RING
Page 8 - on the main PCB and into the Mini-Din Connector on the main PCB.
Installation Guide 8 1) Insert the Circular Mini-Din Connector of the source Component Harness through the wire tie loop on the main PCB and into the Mini-Din Connector on the main PCB. 2) Pull the wire tie loop tight and cut off the excess.3) Connect the Power Harness to the mating connector on the...
Page 9 - Positive Switched Dome lighting; CONNECTING THE DOME LIGHTS
Installation Guide 9 Red / black - Lamp on Black / red - Lamp common Violet / brown - Lamp Auto To 3 pin connector on Monitor To constant +12vdc To constant +12vdc Factory Door ajarswitch or BodyControl computer Factory Dome light circuit Positive Switched Dome lighting CONNECTING THE DOME LIGHTS Th...
Page 10 - No power at Video Monitor; Negative Switched Dome lighting
Installation Guide 10 Troubleshooting: SYMPTOM: No power at Video Monitor P o w e r b u t n o v i d e o o rsound Picture, but no sound REMEDY: -Verify +12 VDC on Red wire at 2 pin Power Harness behind videomonitor. Verify ground connection with continuity test from knowngood ground to black wire at ...
Page 11 - This Page Intentionally Left Blank
Installation Guide 11 This Page Intentionally Left Blank