Audiovox FR-314 - Manual

ÿþýüû ûù ÿ ÿþý ÿþþ FUNCTION AND LOCATION OF THE CONTROLS 3 4 5 6 7 8 9 10 11 13 1 2 12

ÿ LCD DISPLAY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

USING YOUR FR-314 Turning the Transceiver On or Off Pressing the red power button for 2 seconds will turn the FR-314 onor off. If the button conformation tones are active, the transceiverwill play conformation tones when turned on or off. Auto-shutdown Timer,The FR-314 has an internal timer which ca...

LCD Illumination The FR-314 incorporates an electro-luminescent display. Amomentary press of the monitor button will illuminate the LCD. Thebacklighting will remain lit for five seconds. If the up, down, call orfunction buttons are pressed during this period, the LCD will remainilluminated for anoth...

Selecting the Channel To adjust the channel, press the function button once or until thechannel number flashes on the display. Pressing the up or downbuttons momentarily, within five seconds, will change the currentchannel number. The LCD will indicate the current setting and, ifthe beep conformatio...

ÿ Scanning Channels The FR-314 can scan all 14 FRS channels to search for activetransmissions. To begin scanning, press the function button onceor until the channel number flashes on the display, then hold the upor down button for 2 seconds while the channel number is flashing.When the scan mode is ...

Transmitting a signal To Transmit manually1. Set the desired channel number.2. Press and hold the PTT (Push-to-Talk) button while speaking slowly and clearly in a normal voice, approximately 2 to 3 inches fromthe microphone. 3. The transmission icon will be displayed while transmitting and the signa...

Receiving Signals To Receive1. Turn the transceiver on.2. Check the battery condition on the display. If the battery icon is displayed, charge or replace the batteries. 3. Set the desired channel number.4. Adjust the volume control to the desired listening volume by pressing and holding the monitor ...

Adjusting the Squelch The FR-314 has 5 different squelch settings. These settings deter-mine the strength that an incoming signal must have in order to beplayed by the FR-314’s internal speaker or through a headset. Thehigher the setting, the stronger the signal must be in order for theFR-314 to pla...

Selecting a Call Tone The FR-314 has seven built - in call tones. To select a call tone,press the function button twice or until the LCD displays “ x ” the current call tone number will flash on the right of the display. Pressingthe up or down buttons will select between the seven availablesignals. ...

Adjusting the Vox Trigger Level Whenever the Vox mode is selected, it is necessary to adjust itssensitivity setting. There are four available adjustment levels. Whenusing the vox feature in areas where there is a lot of backgroundnoise, choose setting number 1. To avoid inadvertent transmissionsin q...

Using the Monitor feature The FR-314 has a unique feature which allows a pair of units tooperate as a remote monitoring system. A single unit to be placedin an area and transmit sounds from that area to a second FR-314transceiver. The monitor feature allows the user of the secondtransceiver to check...

ÿþýüû ûù ÿ Using the Monitor feature Continued It is now possible for an FR-314 to receive sounds transmitted bythe remote FR-314 in monitor mode at any time. Pressing and holdingthe PTT button, then momentarily pressing and releasing the monitorbutton on the second FR-314 will initiate an 8 second ...

Button Conformation Tones The transceiver can be set to confirm each press of the function,call, up or down buttons with a beep tone or, if the user prefers,these confirmation tones can be turned off. Whenever the tones areon, the letter B inside the speaker icon will be shown on the display.To turn...

Keypad Lock To prevent the transceiver’s settings from being inadvertentlychanged, the keypad can be locked. When the keypad is locked,only the volume is adjustable, the other functions can be viewed,but not changed. This is useful when the FR-314 is being usedby small children, or when the unit is ...

Remove the batteries from the transceiver if it is not expected tobe used for long periods of time. This will eliminate the possibility ofbattery acid leaking from the batteries and corroding the transceiver.Avoid exposing the unit to water or extremes of temperature.Do not use this device in or nea...

Applies to Audiovox Family Radio Service Products. AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 90 days from the date o...