Audiovox APS-620 - Manual
Audiovox APS-620 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALLATION OF THE MAJOR COMPONENTS:; Do Not Mount The Module In The Engine Compartment
- Page 3 – Do not remove the fuse holders from this wire harness.; WIRING THE 6 PIN MAIN POWER HARNESS Connector “C”:; + 12 volt Battery 1 Source; Starter Output
- Page 4 – Wiring The 2 Pin Door Lock/Unlock Harness Connector “B”:
- Page 6 – Pulsed Ground Output Before Start
- Page 9 – Entry Illumination Ground Output; Programming Tach Rate:; NOTE: All applications require that tach be programmed.
- Page 10 – Setting Up The System Programming Features:
- Page 11 – COMPLETING THE INSTALLATION:; ment. Make sure to clean the surface before affixing the label.
1
128-7829
1 of 12
Model APS-620
Installation Manual
This Remote Start System is designed to be used with
Automatic Transmission- Fuel Injection Vehicles Only!
COMPONENTS:
Control Module
2 Four Button RF Transmitters
Antenna/Receiver
1 1” X 1.75” Foam Pad
6 Pin Main Power Harness
7 Pin Accessory Harness
1 Hood Pin Switch
1/4” Female Spade Connector
2 Pin Door Lock/Unlock Harness
3 Pin Parking Light/Ground Harness
2 Pin LED Assembly
2 Pin Push-Button Valet/Program Switch
3 Pin Antenna Receiver Harness
4 Pin Auxiliary Output Harness
4 Philips Head Black Drill Point Sheet
Metal Screw #8 X 1/2"
Installation/Owners Guide
FEATURES:
-Selectable Ignition Lock & Unlock
-Selectable Door Lock/Unlock Output Timing
-Safe Start (Requires double push of the start button to engage the remote start
function)
-On-Board Parking Light Relay
-Trunk Release Output
-Horn Chirp Output With Selectable Duration
-Selectable RF Start Chirp
-Car Finder Mode (Can elect to have horn beep along with parking lights if
connected)
-Selectable Run Times 5, 10, 15, or 20 Minutes
-Selectable Gas or Diesel
-Automatic Start Timer (Can be set to start your car automatically at 2 or 4 hour
intervals)
-4 Negative Pulsed Aux Outputs Before Start, After Start, During Crank, After
Shutdown (To aid installation in many vehicles with factory alarm systems)
FCC NOTICE
This device complies with part 15 of the FCC rules. Operation of this device is subject to the
following conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Caution:
Changes or modifications not expressly approved by the party responsible for
compliance voids the users authority to operate this device.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 128-7829 2 of 12 INSTALLATION OF THE MAJOR COMPONENTS: CONTROL MODULE: Select a mounting location inside the passenger compartment (up behind the dashboard).The mounting location selected must be within 24" of the ignition switch wiring harness toallow connection of the 6 pin main wiring harne...
3 128-7829 3 of 12 DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MULTI PIN INPUT /OUTPUT HARNESS INTO THE CONTROL MODULE UNTIL ALL CONNECTIONS TOTHE VEHICLE HAVE BEEN MADE. AFTER SELECTING YOUR TARGET WIRES ASDEFINED BELOW, DISCONNECT THE NEGATIVE BATTERY CABLE FROM THE VE-HICLE BATTERY PRIOR TO...
4 128-7829 4 of 12 the circuit and select the correct installation method. In addition you will realizewhy the connection of the safety wire is required for all mechanical switch con-figurations. Failure to make this connection properly can result in personal injury and property damage.In all instal...
