Audiovox APS-597 - Manual
Audiovox APS-597 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – P a g e 2; To program these selectable features
- Page 4 – INSTALLATION OF MAJOR COMPONENTS; Channel 3 & Alternate Channel 3
- Page 5 – WIRING THE SYSTEM; some remote start trigger inputs, will damage the control module.
- Page 6 – trunk release circuits will damage the control module.; be active as long as the transmitter button is depressed.
- Page 9 – Pin Upgrade Telematic Module:; COMPLETING THE INSTALLATION
- Page 11 – THIS PAGE LEFT BLANK INTENTIONALLY
128-7407
1 of 12
Model APS-597
Installation Manual
SELECT
ABLE FEA
TURES
The selectable features can be set manually as explained below
, or with the RF feature programmer
.
T
o
set features using the RF programmer
, follow the instructions packaged with the programmer
.
Factory default settings are indicated by bold text.
Note :
The method of manual override can either be selected to operate from the valet switch or operate as custom code.
Be certain to place a check mark indicating the method used in the box located on the last page of the owner's manual.
NOTE: Keyless Entry Models with no horn output will Flash the Parking Lights instead of chirp where chirp is indicated.
Also, No data will be indicated if a feature is not available for a particular model. The unit will enter the feature but no s
election will be available.
RF Programmable Feature Bank 1 Is For T
ransmitter Programming See T
ransmitter Programming Guide.
RF Programmable Features Bank 2 Is Alarm Selectable Features:
Feature Selection
1 Chirp
2 Chirps
3 Chirps
4 Chirps
5 Chirps
6 Chirps
Default
1st DoorL/UL
1 Sec.
3.5 Sec.
1
Sec
L,
Dbl.
U/L
Dbl L, 1 Sec UL
Dbl
L,
Dbl
UL
1
S
l/350mS ul
1S/1S
2nd Accy Lock
Accy
Lock
On
Accy Lock Off
Auto Locks Off
3rd Accy
.
UL
Accy UL Dr
.
Accy
UL
All
Accy U/L Off
Auto UL Off
4th Headlights
O
n
A
rm
O
n
Disarm
On Both
O
ff
w/ Arm& Disarm
5th Passive Locks
Passive
Active
Active
6th Pass/Act Arm
Passive
Arm
Active Arm
Active
7th Siren/Horn
Siren/Horn
Siren Only
Horn Only
Siren/Horn
8th Horn Chirp
10mS
16mS
30mS
40mS
50mS
16mS
9th O/R Method
Custom Code
V
alet
V
alet
10th 2 Step U/L
O
n
Off
Off
1
1th Chp Del Tx
O
n
Off
Off
12th V
olts/HdW
ir
e
V
oltage Sense
Hardwire
Hardwire
13th Trigger Ckts
NA
14th L/UL Poll
N
A
When using the RF programmer
, enter the program mode as follows:
Turn the ignition on
Press and release valet switch 3 times
turn ignition off then on
Press and hold valet switch for 5 seconds
Siren chirps 2 times indicating RF feature program mode.
Note:
Once you enter the feature programming mode, do not allow more than 15 seconds to pass between steps, or the programming will
be terminated.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
128-7407 2 of 12 P a g e 2 To program these selectable features; Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off Then On Long chirp followed by a long chirp This Action Accesses Feature Bank 2 Al...
128-7407 4 of 12 Page 4 INSTALLATION OF MAJOR COMPONENTS Note: This system allows the transmitter to be programmed for single button lock/unlock or separatebutton lock/unlock. The receiver is set up as follows: Channel #1 = Lock/Unlock/Unlock 2 &Panic Channel #2 = If Programmed, Unlock/Unlock 2 ...
128-7407 5 of 12 Page 5 Drill a ¼ “ diameter hole, and pass the red and blue wires from the LED through the hole, from the front ofthe panel. Firmly press the body of the LED into the hole until fully seated.Valet Switch:Select a mounting location for the switch that is easily accessible to the driv...
