Audiovox APS-25HJ - Manual
Audiovox APS-25HJ – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – WIRING THE SYSTEM
- Page 8 – INSTALACIÓN DE LOS COMPONENTES PRINCIPALES; Interruptores de clavija para el capó y baúl:
- Page 9 – CABLEADO DEL SISTEMA; Conexiones de cableado del arnés de alimentación principal:
- Page 12 – SALIDAS PARA
Page 1
Model APS-25HJ
Installation Manual
PROGRAMMABLE FEATURES
RF Programmable Features :
Feature Selection
1 Chirp
2 Chirps
Default
First
1 Second Door Locks
3.5 Second Door Locks
1 Second
Second
Auto Lock On
Auto Lock Off
Auto Lock Off
Third
Auto Unlock On
Auto Unlock Off
Auto Unlock Off
Fourth
Passive Door Locks
Active Door Locks
Active Locks
Fifth
Passive Arming
Active Arming
Passive Arming
Sixth
Voltage Sense On
Voltage Sense Off
Voltage Sense Off
Seventh
Hi-Jack Start Timer 15 Sec.
Hi-Jack Start Timer 45 Sec
Start Timer 45 Sec.
Eighth
Hi-Jack Feature On
Hi-Jack Feature Off
Hi-Jack Feature On
Note :
When both Passive Arming and Voltage Sensing are selected, you must hardwire the driver’s door pin switch in order to begin
the passive arming sequence.
To program these selectable features;
Action
System Response
Turn ignition on
No response
Flip valet switch on then off 3 times
1 Chirp - LED 1 flash
Within 3 seconds, turn ignition Off
Short chirp, then long chirp
First
Then On
1 chirp = 1 second door locks
Press transmitter button 1 to change
2 chirps = 3.5 second door locks
or
Second
Flip valet switch on then off
2 chirps = auto locks off
Press transmitter button 1 to change
1 chirp = auto locks on
or
Third
Flip valet switch on then off
2 chirps = auto unlock off
Press transmitter button 1 to change
1 chirp = auto unlock on
or
Fourth
Flip valet switch on then off
2 chirp = active locks
Press transmitter button 1 to change
1 chirps = passive locks
or
Fifth
Flip valet switch on then off
1 chirp = passive arming
Press transmitter button 1 to change
2 chirps = active arming
or
Sixth
Flip valet switch on then off
2 chirps = voltage sense feature off
Press transmitter button 1 to change
2 chirp = voltage sense feature on
or
Seventh
Flip valet switch on then off
2 chirp = Hi-jack start timer 45 seconds
Press transmitter button 1 to change
1 chirps = Hi-jack start timer 15 seconds
or
Eighth
Flip valet switch on then off
1 chirp = Hi-jack feature on
Press transmitter button 1 to change
2 chirps = Hi-jack feature off
or
Flip valet switch on then off
Exit Program Mode
or
Turn the ignition switch off
Exit Program Mode
Note :
Once you enter the feature programming mode, do not allow more than 15 seconds to pass between steps, or the programming
will be terminated.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Shock Sensor : Select a solid mounting surface for the shock sensor on the firewall inside the passenger compartment,and mount the sensor using the two screws provided. The shock sensor can also be secured to anyfixed brace behind the dash using tie straps.Whichever mounting method is selected, make...
Page 8 INSTALACIÓN DE LOS COMPONENTES PRINCIPALES Módulo de control: Elija un lugar de montaje adentro del compartimiento del pasajero (arriba y detrás del tablero de instrumentos) y fijecon los dos tornillos provistos. No instale el módulo en el compartimiento del motor dado que no es impermeable. ...
Page 9 CABLEADO DEL SISTEMA Conexiones de cableado del arnés de alimentación principal: Cable rojo con fusible: FUENTE CONSTANTE DE BATERÍA DE +12 VCC Este cable alimenta el módulo de control y controla la sensibilidad del circuito de detección de voltaje que detectael encendido o apagado de una luz...
