Page 3 - PACKING LIST
CD Magazine (P/N ACC-56MAZ) 1 pc. Index label sheet 1 pc. Owner's Manual and Installation Guide 1 pc. Self-tapping screw (M5 x 12) 4 pcs. Seals (A) 1 pc. 5 Meter Din Cable 1 pc. Hexagonal bolt with washer (M5 x 10) 7 pcs. INSTALLATION PARTS OTHER ACCESSORIES MAIN UNIT PACKING LIST Changer Bracket (L...
Page 4 - Installation and Wiring Precautions; BEFORE INSTALLING THE UNIT; Transport Lock Screws; ADDITIONAL 10-DISC MAGAZINES
NOTE: If the changer is to be installed in a car that is equipped with an on-board drive or navigation computer, do not disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under theseconditions, use extra caution during installation not to cause a short circu...
Page 5 - WHERE TO INSTALL THE CHANGER
5 MOUNT ON FLOOR OF TRUNK(HORIZONTAL OR 45 DEGREES) MOUNT ONSIDEWALL OFCARGO AREA MOUNT ON BULKHEAD BEHINDSEAT OF PICKUP TRUCKS MOUNT ON BACKWALLOF HATCH AREA MOUNT ON SIDE OFTRUNK SIDEWALL TRUNK MOUNTING (SEDANS) This is usually the easiest location to use as there is ample spaceavailable. Check th...
Page 6 - INSTALLATION; PROCEDURE FOR HORIZONTAL INSTALLATION
6 INSTALLATION The ACC-56 changer is designed for horizontal (flat), vertical (upright) or 45-degree mounting. It must never be mounted upside-down or on either one of it's sides as explained previously. The position of the built-in anti-vibration springs (left and right side), must correspond to th...
Page 7 - PROCEDURE FOR VERTICAL INSTALLATION
7 PROCEDURE FOR VERTICAL INSTALLATION NOTE:If the anti-vibration spring position has been changed and verified for vertical mounting (as shown on page 6), start with step 2. Hexagonal boltwith washer base (M5 x 8) Bracket (R) Bracket (L) 4 2 Attach bracket (L) and bracket (R) to each side of the uni...
Page 8 - PROCEDURE FOR 45° ANGLE INSTALLATION
8 PROCEDURE FOR 45° ANGLE INSTALLATION NOTE:If the anti-vibration spring position has been changed and verified for 45° angle mounting (as shown on page 6), start with step 2. 4 2 Attach bracket (L) and bracket (R) to each side of the unit,using the hexagonal bolts with washer base (M5 x 8). Mount t...
Page 9 - OVERALL WIRING VIEW
9 OVERALL WIRING VIEW This page is provided to give you a quick look at the entire wiring of the ACC-56. Use it to plan your wire routingpaths and possible connection points. Detailed wiring is explained in the following pages. NOTE: When routing wires and cablesfrom the rear of the car to the dash-...
Page 10 - ORANGE WITH WHITE STRIPE WIRE
10 WIRING THE FM MODULATOR The FM modulator should be positioned near your existingcar stereo and the 15 foot data cable should be connected to it.Make the following connections to the FM modulator: DATA CABLE The 15 foot data cable connects the changer to the FM module.First connect the end of the ...
Page 11 - CAR ANTENNA INPUT; RADIO ANTENNA OUTPUT
CAR ANTENNA INPUT Locate your existing car radio antenna cable. This isnormally a black cable about as thick as a pencil andwill be plugged into a socket on the rear of your carradio. Unplug this antenna lead and plug it into themating female socket on the FM modulator.IMPORTANT - Some Import cars h...
Page 13 - REMOTE CONTROL OPERATING INSTRUCTIONS
CONTROLS LCD Display Track/Disc Scan (SCN) Track/Disc Repeat (RPT) Track/Disc Shuffle (SFL) Reset Button Play/Pause ( / II) Power Off Switch (OFF) Track (TRK) Select ( ) Track (TRK) Search ( ) Disc Select ( +/- ) PREPARING FOR OPERATION 1. Load CD magazine bm and insert into changer as described on ...
Page 14 - USE OF CONTROLS
14 USE OF CONTROLS is provided to protect the unit's microprocessor and laserpickup system and should only be activated under thefollowing circumstances:1. Initial installation after all wiring is completed (this must be done). 2. If abnormal disc operation is encountered, the reset button may be pr...
Page 15 - HANDLING THE DISCS; HINTS FOR CORRECT AND SAFE OPERATION
This CD Changer is designed to be operated only on 12 volt DC negative ground systems. The unit cannot be used on 24 voltor positive ground systems. TEMPERATUREThe unit may not operate correctly in extremely hot or cold temperatures. It is equipped with a built-in thermal protection circuitwhich wil...
Page 16 - USE OF THE CD MAGAZINE
LOADING DISCS INTO THE MAGAZINEThis CD Changer uses a specially-designed magazine to holdup to 10 compact discs. To load discs into the magazine, gripthe tab on the magazine tray into which you will be loading adisc and pull it out gently as shown in Figure 1. Pull out only onetray at a time. Insert...
Page 17 - CD CHANGER OPERATING INSTRUCTIONS; Accessories Supplied:
CD CHANGER OPERATING INSTRUCTIONS This CD Changer is designed to operate through a compatible Audiovox car stereo which incorporates thecontrols and display functions or through the FM section of any car stereo. Please check with your Audiovoxstereo specialist for recommendations of the models that ...
Page 18 - TROUBLESHOOTING
TROUBLESHOOTING An error made in operation or during installation of this product may be mistaken for a system malfunction. Please performthe checks described below before contacting your dealer or service facility. No power Magazine cannot beinstalled CD is not played Noise, skipping, orintermitten...
Page 19 - 2 MONTH LIMITED WARRANTY
AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this productthat should this product or any part thereof, under normal use and conditions, be proven defectivein material or workmanship within 12 months from the date of original purchase, such defect(s) willbe repaired...
