Apple Logic Board - Manual

Apple Logic Board

Apple Logic Board – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
Page: / 20

Table of Contents:

  • Page 3 – Xserve Logic Board -; Figure 2; Place the bottom housing on a sturdy, flat surface and ESD mat.
  • Page 4 – Removing the Installed Logic Board; Memory DIMMs; Figure 3
  • Page 5 – Figure 4
  • Page 6 – Figure 6; Heatsink and Processor, Version 1; blower, and lift the end of the duct as shown.; Figure 7
  • Page 7 – Figure 8; Remove the processor from the server.; Figure 9
  • Page 8 – Heatsink and Processor, Version 2; processor to the logic board.
  • Page 9 – ATA Controller Board; logic boards and remove the board from the server.
  • Page 10 – Power Supply; cable from the drive interconnect board.
  • Page 11 – Logic Board; Remove the board from the server.
  • Page 12 – Installing the Replacement Logic Board; over the four mounting pegs on the chassis floor.
  • Page 13 – Reconnect the power supply to the logic board.; printed on it points toward the logic board, and press down.
  • Page 16 – processor connector and twist until the guide screws into place.
  • Page 18 – PCI/AGP Card Risers and Memory DIMMs; Reconnect the dual- and single-slot risers to the logic board.
  • Page 19 – Battery; panel with the new ID label.; Closing the Server; Carefully slide the bottom housing back into the rack.; parts can damage it or cause injury.
Loading the manual

073-0665 Rev. D

Xserve

Logic Board

Replacement Instructions

Follow the instructions in this sheet carefully. Failure to follow these instructions could

damage your equipment and void its warranty.

Note:

Online instructions covering customer-installable parts are available at

http://www.info.apple.com/installparts/.

Tools Required

The only tool required for this procedure is a Phillips screwdriver.

Opening the Server

The server slides open from the front of the rack. The top cover remains in place in the

rack while the bottom housing (containing all internal components) should be placed on a

sturdy, flat surface.

1.

Alert users that the server will be unavailable for a period of time.

2.

Shut down the server.

Warning: To avoid damaging internal components or causing injury, always

shut down the server before opening it. After you shut down the server, internal

components can be very hot. Let the server cool down before continuing.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 3 - Xserve Logic Board -; Figure 2; Place the bottom housing on a sturdy, flat surface and ESD mat.

Xserve Logic Board - 3 8. Grasp the thumbscrews and slide the bottom housing forward part way to expose the two chassis levers. (Figure 2) 9. While depressing both levers, pull the bottom housing all the way forward and remove it from the rack. Figure 2 10. Place the bottom housing on a sturdy, flat...

Page 4 - Removing the Installed Logic Board; Memory DIMMs; Figure 3

Xserve Logic Board - 4 Removing the Installed Logic Board Note: The replacement logic board does not include memory DIMMs or expansion cards. You must transfer these parts from the current logic board. To remove the logic board, you must first remove: • memory DIMMs • PCI/AGP card risers • heatsink ...

Page 5 - Figure 4

Xserve Logic Board - 5 Dual-Slot Riser 1. Release the thumb screw that secures the riser’s cards to the server. (Figure 4) 2. If there are latches on either side of the riser, lift them slightly to release the riser from the logic board. 3. Pull the riser a short distance to the side to disconnect i...

Other Apple Models

All Apple Other