Page 2 - Copyright Declaration
Motherboard XP-K7S748 Jul. 2, 2004 Jul. 2, 2004 XP-K7S748 Motherboard Copyright Declaration © 2004 Gigatrend Technology Co., Ltd. All rights reserved. No part of this manual may bereproduced, copied, translated, or transmitted in any form or by any means without expresspermission from Gigatrend Tech...
Page 3 - Contents
Contents Motherboard Layout ........................................................................ 4 1. Production Introduction ............................................................. 5 1.1. Feature Summary .............................................................................. 5 1.2....
Page 4 - English; Motherboard Layout
4 English Motherboard Layout CODEC KB_MS COMA LPT USB LAN F_AUDIO AUDIO XP-K7S748 SOCKET A CPU_FAN ATX CD_IN SiS 748 BIOS AGP COMB FDD F_USB BATTERY IT8705F IDE2 963L PCI1 IDE1 PCI2 PCI3 PCI4 F_PANEL PWR_LED DDR2 DDR3 SYS_FAN PCI5 DDR1 RTL8201 SW1 USB
Page 5 - Production Introduction; Feature Summary
English 5 CPU Socket A for AMD Athlon TM XP/Athlon TM /Duron TM processor 400/333/266MHz FSBSupports 1.4GHz and faster Chipset North Bridge: SiS 748South Bridge: SiS 963L Memory 3 184-pin DDR DIMM sockets, support up to 3GB DRAM (Max)Supports DDR400/DDR333/DDR266 DIMMSupports only 2.5V DDR SDRAM Slo...
Page 6 - I/O Back Panel and Connectors & Jumper Setting; Connectors & Jumper Setting
6 English 1.2. I/O Back Panel and Connectors & Jumper Setting 1.2.2. Connectors & Jumper Setting FDD (Floppy Disk Drive Connector) The FDD connector is able to connect a single floppy disk drive via a FDD cable. Usually one edge of the FDD cable is marked in red, please attach this marked ed...
Page 9 - Hardware Installation; Installation of a Socket A CPU and Fan Sink
English 9 2. Hardware Installation 1. Please make sure that the CPU used is supported by your motherboard. 2. Please be aware of the placement position of the CPU. If the CPU does notinsert properly, do not apply force but check the placement position. 3. Please make sure that an even layer of heat ...
Page 10 - Installation of Memory
10 English 2.2. Installation of Memory 1. Before installing or removing memory, please make sure that the computer poweris turned off to prevent hardware damage. 2. Please make sure that the memory used is supported by the motherboard. 3. Memory modules have a foolproof insertion design. The memory ...
Page 11 - BIOS Setup
English 11 3. BIOS Setup BIOS (Basic Input and Output System) stores all the information of the motherboard settings that is needed for system initiation within the CMOS. The CMOS SETUP utility allows the user to make changes in BIOS configurations that are required or to activate certain features.T...
Page 12 - Standard CMOS Features
12 English <F6> Gives the list of options available for each item <F7> Return to Optimized default values (not applicable to main setup screen) <F8> Enters BIOSNow! feature <F9> Displays system information <F10> Saves settings and exits setup 3.2. Standard CMOS Features...
Page 13 - Floppy 3 Mode Support
English 13 n Floppy 3 Mode Support Allows user to configure a Japanese standard 3 Mode floppy drive. Options: Disabled (No 3 Mode drive installed) Drive A (3 Mode Drive installed in A:) Drive B (3 Mode Drive installed in B:)Both (3 Mode Drive installed in A: and B:) n Halt on Tells the BIOS specific...
Page 14 - Advanced BIOS Features; Boot Up Floppy Seek; Init Display First
14 English 3.3. Advanced BIOS Features ø Allows the configuration of advanced settings such as boot sequence, password check, etc. n First / Second / Third Boot Device The user can select the order in which the system will boot. Options: Floppy, LS120,HDD-0~HDD3, SCSI, CDROM, ZIP,USB-FDD, USB-ZIP, U...
Page 15 - Integrated Peripherals
English 15 n IDE1 Conductor Cable Allows user to select the type of IDE1 conductor cable. Prior to selecting the setting, please make sure that the IDE device and cables support the desired setting. Options: Auto, ATA66/100, ATA33 (default:Auto) n IDE2 Conductor Cable Allows user to select the type ...
Page 17 - Power Management Setup; ACPI Suspend Type; System After AC BACK; ModemRingOn
English 17 CMOS Setup Utility-C op yright (C ) 1984-2004 Award So ftware Po wer Managemen t Setup AC PI Susp end Ty pe [S1(POS)] So ft-Off by PWR _BTTN [Off] Sy stem After AC Back [Off] IRQ [3-7, 9-15], NMI [Enab led] ModemRingOn [Enab led] PME Event Wake Up [Enab led] Po wer On b y Keyboard [Disabl...
Page 18 - PnP/PCI Configuration
18 English 3.6. PnP/PCI Configuration ø This menu allows you to configure your PCI slots. You can assign IRQ's for various PCI slots. n PCI4 IRQ Assignment Allows you to assign an IRQ for the fourth PCI slot. Options:Auto,3,4,5,7,9,10,11,12,14, 15 (default:Auto) n PCI1/PCI5 IRQ Assignment Allows you...
Page 19 - Current CPU Temperature; PCI2 IRQ Assignment
English 19 3.7. PC Health Status ø This menu displays the current CPU temperature, the fan speeds, voltages etc. n Current Voltage(V) Vcore / DDR25 / +3.3V / +12V Automatically checks system voltage n Current CPU Temperature Automatically checks CPU temperature n Current CPU/System FAN Speed (RPM) A...
Page 20 - Frequency/Voltage Control; Linear Frequency Control; AGP Voltage Control
20 English 3.8. Frequency/Voltage Control ø This allows user to configure CPU frequency and voltage settings. ø This section is very dangerous for inexperienced users, and therefore it is notrecommended that these settings be altered. An incorrect setting can result in system instability, corrupt da...
Page 21 - Top Performance; Load Optimized Defaults; CPU Voltage Control
English 21 3.9. Top Performance ø "Top Performance" allows faster system start. However, the result may differ depending on system specifications (includes hardware and OS). For example, certain hardware may become unstable under Windows XP but work reliably under the Windows NToperating sys...
Page 22 - Driver Installation; Exit Without Saving
22 English 4. Driver Installation Driver installation for the Windows 98/98SE/200/ME/XP operating systems is simple. Once you insert the provided driver disks into your optical drive, the AUTORUN screen will appear.If this screen does not appear, you can use "D:\setup.exe" (with "D" ...
