Page 2 - Important Safety Information; Installation
2 Important Safety Information You MUST read these warnings carefully before installing or using thehob. If you need assistance, contact our Customer Care Department on08705 350350 Installation z This hob must be installed by qualified personnel, according to the manufacturer’s instructions and to t...
Page 4 - Contents; Guide to Use the instructions
4 Contents Important Safety Information ................................................................................ 2Instructions for the User ........................................................................................ 5 Description of the Hob .........................................
Page 5 - Description of the Hob; INSTALLATION; WHEN THE HOB IS FIRST INSTALLED
5 1. Hob Top 2. Rapid Burner 3. Semi-rapid Burners 4. Auxiliary Burner 5. Control knob for back right burner (semi-rapid) 6. Control knob for back left burner (semi-rapid) 7. Control knob for front left burner (rapid) 8. Control knob for front right burner (auxiliary) Description of the Hob INSTALLA...
Page 6 - HOB BURNERS; Operation
6 HOB BURNERS To light a burner, turn the relevant control knob anticlockwise to the maximum position, then push it down to ignite the burner. Upon, ignition, keep the knob pushed down about 5 seconds, then adjust the flame as required.If the burner does not ignite, turn the control knob to zero, an...
Page 7 - Pan Supports; Maintenance and Cleaning
7 Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. Pan Supports To keep the pan supports in the correct position, they ar...
Page 8 - Something Not Working?
8 Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local AEG Service Force Centre. SYMPTOM There is no spark when lighting the gas The gas ring burns unevenly SOLUTION Check that the unit is plugged in and the electrical s...
Page 10 - Guarantee Conditions; Standard guarantee conditions; Exclusions; European Guarantee
10 Guarantee Conditions Standard guarantee conditions We, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or any part thereofis proved to be defective by reason only of faulty workmanship or materials, we will, at our discretion repair orreplace the same FREE O...
Page 11 - Engineer technical data
11 Burner Dia. Tap By-pass 1/100 mm Auxiliary 28 Semi-rapid 32 Rapid 40 Aeration adjustment none OVERALL DIMENSIONS Width: 580 mm. Depth: 510 mm. Height: 88 mm. Weight: 8 Kg. CUT OUT DIMENSIONS Width: 550 mm. Depth: 470 mm. Thickness: 30 mm. SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear r...
Page 12 - Important safety requirements
12 BURNER RAPID SEMI-RAPID AUXILIARY (large) (medium) (small) POSITION MAX MIN MAX MIN MAX MIN NOMINAL THERMAL POWER kW 2.9 0.65 1.9 0.45 1.0 0.33 NOMINAL FLOW RATE m 3 /h 0.276 0.062 0.181 0.043 0.095 0.031 NOZZLE REFERENCE 119 Adjust. 96 Adjust. 70 Adjust. 1/100 mm NOMINAL THERMAL POWER kW 2.7 0.6...
Page 13 - Location
13 Installation IMPORTANT This hob must be installed by qualified personnel to the relevant British Standards.Any gas installation must be carried out by a registered CORGI installer. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions in...
Page 14 - Gas Connection
14 A) End of shaft with nut B) Washer C) Elbow FO 0814 FO 0264 On the end of the shaft, which includes the GJ 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force. It is import...
Page 15 - Cut Out Size
15 550 470 580 510 Cut Out Size The dimensions of the cut-out are given in the diagram. Building InBuilding over a cupboard ordrawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surf...
Page 17 - Electrical connections
17 Electrical connections Any electrical work required to install this hob should be carried out by a qualifiedelectrician or competent person, in accordance with the current regulations.THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed.Th...
Page 18 - Permanent Connection; Wiring diagram; Replacement of the cable
18 Permanent Connection In the case of a permanent connection, it is necessary that you install a double poleswitch between the hob and the electricity supply (mains), with a minimum gap of 3mm. between the switch contacts and of a type suitable for the required load incompliance with the current el...
Page 19 - Fault Finding; Preliminary Electrical Systems Check
19 Fault Finding Preliminary Electrical Systems Check START Isolate applianceand carry out: A: Earth Continuity check. Has inlet fuse blown? Carry out: C: Polarity check. Electricity supplyshould now besatisfactory. Carry out: D: Resistance to Earth check. Inlet wiringfaulty.Rectify anyfault. Isolat...
Page 21 - Ignition System / Gas Ignition
21 Check gas supply atburner Ignition System / Gas Ignition YES Check plug top fuse andreplace if necessary Check polarity and earthcontinuity of supply point Check earth continuityof appliance Ignitor does not spark Check fitting ofburners Check position of theelectrode Check by pass simmeradjusted...
Page 22 - Commissioning; Pressure Testing
22 Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. 1) Turn the gas tap to the MAX position and ignite.2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several t...
Page 23 - Conversion from Natural Gas to LPG; Method; To adjust the gas rate
23 Conversion from Natural Gas to LPG It is important to note that this model is designed for use with natural gas but can beconverted for use with butane or propane gas providing the correct injectors arefitted and the gas rate is adjusted to suit. Method 1) Ensure that the gas taps are in the 'OFF...
