ADTRAN DDM + H2TU-C - Manual
ADTRAN DDM + H2TU-C – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
JOB
A
ID
61222003L2-22A
0104
DDM+ H2TU-C
CLEI: T1L3X5BA_ _
STATUS LEDs
STATUS
●
RED
Alarm on the H2TU-C loop, H2R loop, DSX or DS1 interface.
✷
FLASHING
Signal Quality of 0 or No Sync on the loop.
●
AMBER
Loopbacks active.
✷
FLASHING
In-band loopbacks armed.
●
GREEN
Functioning properly.
✷
FLASHING
ES, SES, or BPV detected at either DSX or DS1 interface.
RS-232 DB-9 CONNECTOR
■
Used to access the HDSL2 utilities menu tree via VT100 emulation software such as
Terminal, Hyper Terminal – Private Edition, and ProComm Plus.
■
There are two types of terminal emulation modes, Manual and Real-Time. To toggle
between the two modes, type “CTRL” and “T.” To update the screens while in Manual
Mode, press the space bar 3 times. Real-Time Update Mode is the default.
■
Provision terminal port as follows:
Data Rate
— 1.2 kbps to 19.2 kbps
Asynchronous Data Format
— eight data bits, no parity (none), one stop bit, and no
flow control.
■
Hardware Flow Control – disabled.
■
When using a PC with terminal software, be sure to disable any power saving programs.
COMPLIANCE CODES
This product is intended to be installed in an enclosure with an Installation Code (IC)
of “B” or “E” and in Restricted Access Locations only.
WARRANTY
Warranty for Carrier Networks products manufactured by ADTRAN and supplied under
Buyer’s order for use in the U.S. is ten (10) years. For a complete faxback copy of
ADTRAN’s
U.S. and Canada Carrier Networks Equipment Warranty
: (877) 457-5007,
Document #414.
CIRCUIT BOARD 6-POSITION DIP SWITCH – SW1
Provisions the unit. (Default settings are in
bold
.)
SW1-1
■
Selects line coding to AMI or
B8ZS
SW1-2
■
Selects T1-framing to
FRAMED
or UNFRAMED
1
SW1-3
■
Selects T1-framing to SF or
ESF
SW1-4
■
ENABLES
or DISABLES the NIU loopback
SW1-5
■
ENABLES or
DISABLES
the loopback timeout
2
SW1-6
■
ENABLES or
DISABLES
the shelf alarm
1
UNFRAMED operation ignores the setting of SW1-3
2
Default timeout setting is 20 minutes when loopback timeout is ENABLED
CIRCUIT BOARD 5-POSITION ROTARY SWITCH – SW2
Sets the DSX-1 Line Build Out (LBO). (Default settings are in
bold
.)
■
0 — 0-133 feet of LBO
■
133 — 133-266 feet of LBO
■
266 — 266-399 feet of LBO
■
399 — 399-533 feet of LBO
■
533 — 533-655 feet of LBO
D D M + H 2 T U - C
Code
Input Output
Installation Code (IC)
A
—
Telecommunication Code (TC)
—
X
Power Code (PC)
F
C
C A U T I O N
C A U T I O N !
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
For a complete Installation and Maintenance faxback document: (877) 457-5007, Document #695. Please have your fax number available.
SW2
0
0
133
DSX-1 LBO
533
399
266
2
7 1
4
6
3
5
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
