ADTRAN BR10 - Manual
ADTRAN BR10 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
B R 1 / 1 0 2 X M I N I I S D N C H A N N E L B A N K
JOB
A
ID
61150081L2-22A
0201
BR1/10 2X
CLEI: D4MEXZB02_ _
■
For a complete Installation and Maintenance Practice faxback: (877) 457-5007, Document # 662. Please have your fax number available.
■
C A U T I O N
C A U T I O N !
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
COMMONS /OPTIONS
BR1/10 Common Unit required for each side of the 2X chassis
H-LIU – Combination PAU/LIU
P/N 1150179L1
CLEI: D4IMEG02AA
This unit replaces the individual PAU and LIU cards (shown).
PAU – Power/Alarm Unit
P/N 1150078L2
CLEI: D4CIJ8Y2AA
This common unit has no options switches to set, verify the 1 AMP fuse is properly seated..
LIU - Line Interface Unit
P/N 1150079L2
CLEI: D4CIPT02AA
The LIU has no option switches to set. The DB9 connector and rotary switches are used for
testing only.
BCU- Bank Controller Unit
P/N 1150080L1
CLEI: D4CIS7Z2AA
The BCU is the only common unit with option settings on the printed circuit board.
BCU Option Settings:
S1-1 through S1-3 DSX-1 Line Build Out: 0-133ft/133-266/266-399/399-533/533-655
S2-1 Line Code Format: B8ZS/AMI
S2-2 Framing Format: ESF/SF
S2-3 Remote Loopback Selection: PAYLOAD/LINE
S2-4 and S2-5 Timing Mode:EXTERNAL/LOCAL/LOOP/CAU
S2-6 Bank Mode: 8DSL/10DSL
S2-7 through S2-9 Terminal Mode: D4/ D1D/SLC Mode 1D1D/SLC Mode 3 D4/ D1D
Mini U-BR1TE Switch Options
ON
OFF
SW1
B1 SER. ON
B1 SER. OFF
SW2
B2 SER. ON
B2 SER. OFF
SW3
D SER. ON
D SER. OFF
SW4 SC
ON
S.C.
OFF
SW5
LULT
LUNT
SW6
LULT
LUNT
SW7
ZBS ON
ZBS OFF
Faceplate LED on mini U-BR1TE
Red- Indicates no sync to ISDN Switch/NT1
Green- Indicates sync to ISDN Switch/NT1
BCU MANUAL TESTING DIP SWITCHES
LB ON/OFF
Enables and disables DS1 loopbacks for REMOTE/LOC
direction depending on switch setting below
REMOTE/LOC
REMOTE in ESF will initiate a loopback to the far-end BR1/10
side when LB is switched to ON
REMOTE in SF will initiate a loopback at the local BR1/10 side
when LB is switched to ON
LOC provides internal loopback at the T1 data stream at the
local BR1/10 side when LB is switched to ON
DS0/DS1
When set towards DS1 controls the REMOTE/LOC loopback
directions and initiates loopback with LB ON/OFF switch
When set towards DS0 controls the B1/B2 channel selection.
The TEST recessed button initiates test selected on LIU rotary
switches. This option is normally in the DS0 position once the
BR1/10 side is in service
B1/B2
When the switch above is in the DS0 position, B1 and B2
selects the appropriate B-Channel to be tested
Mini U-BR1TE Compatible Access Cards
Mini BR1/10 ISDN U-BR1TE
1150077LX
CLEI: D4C1A2T2AA (Shown)
Mini BR1/10 TR ISDN UBR1TE
1152182LX
CLEI: D4CIA9T2AA
Mini BR1/10 TR DDS DP
1151061LX
CLEI: D4D3M14DAA
Mini BR1/10 DSO DP
1150103L1
CLEI: D4D3D3HDAA
BR1/10 Slot to Channel Bank Slot Cross-Reference Compatibility
BR1/10
1
2
3
4
5
6
7
8
9
10
D4/DID, SLC Mode 3
1
4
7
10
13
16
19
22
N/A
N/A
SLC Mode 1 (Physical Slots)
1
2
4
5
7
8
10
11
N/A
N/A
Digroup-A
1/2
3/4
7/8
9/10
13/14
15/16
19/20
21/22
N/A
N/A
Digroup-B
25/26
27/28
31/32
33/34
37/38
39/40
43/44
45/46
N/A
N/A
Digroup-C
49/50
51/52
55/56
57/58
61/62
63/64
67/68
69/70
N/A
N/A
Digroup-D
73/74
75/76
79/80
81/82
85/86
87/88
91/92
93/94
N/A
N/A
SLC Mode 3 (Physical Slots)
1
4
7
10
13
16
19
22
N/A
N/A
Digroup A/B
25/26
31/32
37/38
43/44
1/2
7/8
13/14
19/20
N/A
N/A
Digroup C/D
73/74
79/80
85/86
91/92
49/50
55/56
61/62
67/68
N/A
N/A
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
