Zenoah G2000T - Manual - manualsarea.com

Page 3 - For safe operation; WARNING

G2000T GB-3 G B 1. For safe operation WARNING This chainsaw has been especially designed for treemaintenance and should therefore only be used bytrained operators when working on trees. 1. Never operate a chain saw when you are fatigued, ill, or upset, or under theinfluence of medication that maymak...

Page 7 - Explanation of Symbols on the Machine

G2000T GB-7 G B 2. Explanation of Symbols on the Machine The port to refuel “MIX GASOLINE” Position: Fuel cap The port to top up chain oil Position: Oil cap Setting the switch to the “O” position, the engine stops immediately. Position: Front at the top of the rear handle Starting the engine. If you...

Page 8 - Installing Guide Bar and Saw Chain

G2000T GB-8 Open the box and install the guide bar and the sawchain on the power unit as follows: The saw chain has very sharp edges. Use thick pro-tective gloves for safety. 1. Pull the guard towards the front handle to check that the chain brake is not engaged. 2. Loosen the nuts and remove the ch...

Page 9 - Fuel and Chain Oil

G2000T GB-9 G B 4. Pour in the rest of gasoline and agitate again for at least one minute. As some oils may be difficult to agitate de-pending on oil ingredients, sufficient agitation is nec-essary for the engine to last long. Be careful that, if theagitation is insufficient, there is an increased d...

Page 10 - Operating the Engine

G2000T GB-10 6. When engine has ignited, first turn in the choke knob to the first-stage position (2) and then pull the starteragain to start the engine. 7. Allow the engine to warm up with the throttle lever pulled slightly. Keep clear of the saw chain as it will start rotatingupon starting of engi...

Page 11 - STOPPING THE ENGINE; CHAIN BRAKE; GUARD AGAINST KICKBACK

G2000T GB-11 G B • When the brake operates, release the throttle leverto slow down the engine speed. Continuous opera-tion with the brake engaged will generate heat fromthe clutch and may cause trouble. • At machine inspection prior to each job, check theoperating condition of the brake following th...

Page 13 - Way of the cooling air; MAINTENANCE AFTER EACH USE

G2000T GB-13 G B 3. Oil filter 1. With a wire hook, take out the oil filter from the feed- ing port. 2. Wash the filter with gasoline. When returning the filter, use a pinchand make sure that the pipe is notfolded and the filter is placed at thebottom of the tank as shown in thepicture. 4. Spark plu...

Page 14 - SAW CHAIN; Maintenance of Saw Chain and Guide Bar; GUIDE BAR

G2000T GB-14 ■ SAW CHAIN It is very important for smooth and safe operation toalways keep the cutters sharp. The cutters need to be sharpened when:• Sawdust becomes powder-like.• You need extra force to saw in.• The cut path does not go straight.• Vibration increases.• Fuel consumption increases. Cu...

Page 15 - Troubleshooting Guide; Case 1. Starting failure; Rough idling

G2000T GB-15 G B 9. Troubleshooting Guide Case 1. Starting failure Make sure the icing prevention system is not working. Check fuel for wateror substandard mix-ture. Replace with properfuel. C h e c k f o r e n g i n eflooding. Check spark ignition. Remove and dry thespark plug.Then pull the starter...

Page 16 - Limited warranty; T H E WA R R A N T Y D O E S N OT A P P LY TO; THIS WARRANTY DOES NOT COVER; THERE ARE NO OTHER EXPRESS WARRANTIES.; ARE LIMITED

G2000T GB-16 Limited warranty Should any failure occur on the product under normaloperating conditions within the applicable warranty pe-riod, the failed part will be replaced or repaired free ofcharge by a ZENOAH authorized dealer. WARRANTY PERIOD: 1 year (6 months if used profes- sionally, and 30 ...

Zenoah G2000T - Manual

Table of Contents:

Summary

Other Zenoah Models