Zenoah TR2001DL - Manual

1. R e a d t h i s m a n u a l c a r e f u l l y u n t i l y o u

completely understand and can follow all
safety notes, precautions, and operating
instructions before using of the unit.

2. Do not operate this tool when you are tired,

ill, or under the influence of alchohol, drugs,
or medication.

3. Always wear eye or face protection and

hearing protection.

4. Do not wear loose clothing, jewelry, short

trousers, sandals, or go barefoot. Do not
wear anything which might be caught by
branches or moving part of the unit. Secure
hair so it is above shoulder length.

5. N e v e r s t a r t o r r u n t h e e n g i n e i n s i d e a

closed room or building. Exhaust gases
contain dangerous carbon monoxide.

6. B e f o r e s t a r t i n g t h e e n g i n e , i n s p e c t t h e

e n t i r e u n i t f o r l o o s e f a s t e n e r s a n d f u e l
l e a k a g e . M a k e s u r e t h a t t h e c u t t i n g
a t t a c h m e n t i s p r o p e r l y i n s t a l l e d a n d
securely fastened.

7. B e s u r e t h e b l a d e g u a r d i s a t t a c h e d i n

place.

8. Fuel is highly flammable. Always keep open

flames and sparks away from the unit and
fuel depot. Do not smoke while refueling the
unit or mixing fuel.

9. When refueling the unit, make sure to stop

the engine and allow it to cool down. Wipe
spilled fuel completely from the unit. Move

848J6593A0 (406)

OWNER’S MANUAL

BRUSHCUTTERS

TR2001DL

1

2

(1) Read the owner's manual.
(2) W e a r a h e l m e t , e a r p r o t e c t i o n a n d e y e

protection.

(3) Warning / Attention
(4) Keep all children, bystanders and helpers

15 meters away from the brushcutter.

Explanation of pictorials

at least 3 meters away from fueling site
before starting the engine.

10.C h e c k t h e c o n d i t i o n o f w o r k i n g a r e a t o

a v o i d a n y a c c i d e n t b y h i t t i n g h i d d e n
obstacles such as stumps, stones, cans, or
broken grass.

11.Keep bystanders and animals at least 15

meters away from the operating point, If you
a r e a p p r o a c h e d , i m m e d i a t e l y s t o p t h e
engine.

12.K e e p f i r m f o o t h o l d s a n d b a l a n c e a t a l l

times. Do not use the unit where footing is
unsteady or slippery.

13.Keep cutting attachment below waist level.
14.Keep all parts of your body away from the

r o t a t i n g c u t t i n g a t t a c h m e n t a n d h o t
surfaces.

15.Warn the operator of the danger of blade

thrust. (Kick back)
Blade thrust may occur when the spinning
blade contacts a solid object in the critical
a r e a . A d a n g e r o u s r e a c t i o n m a y o c c u r
causing the entire unit and operator to be
thrust violently. This reaction is called Kick
back. As a result, the operator can lose
control of the unit which can cause serious
or fatal injury. Kick back is more likely to
occur in areas where it is difficult to see the
material to be cut.

16.When inspecting or servicing the unit, make

sure to stop the engine and disconnect the
spark plug as necessary.

17.Cover the blade when the transporting or

storing the unit. Secure the unit before for

storage or transporting to prevent loss of
fuel, damage or injury.

18.When replacing cutting attachment or other

c o m p o n e n t s , b e s u r e t o u s e t h e p a r t s
supplied or recommended by KOMATSU
ZENOAH.

19.When the unit is turned off, make sure the

cutting attachment has stopped before the
unit is set down.

20.For units equipped with a clutch, be sure

the cutting attachment stops turning when
the engine idles.

21.U s e o n l y f o r t a s k s e x p l a i n e d i n t h e

instruction handbook.

22.D i s c a r d b l a d e s t h a t a r e b e n t , w a r p e d ,

cracked, broken or damaged in any way.

23.Instructions on stopping a coasting blade.

A blade can injure while it continues to spin
after the engine is stopped or throttle control
is released.

24.Stop the engine and blade before removing

material that is blocking or entangling the
cutting attachment.

25.Use a sharp blade. A dull blade is more

l i k e l y t o s n a g a n d t h r u s t . R e p l a c e t h e
f a s t e n i n g n u t a c c o r d i n g t o t h e
manufacturer's instruction.

26.C u t o n l y m a t e r i a l r e c o m m e n d e d b y t h e

manufacturer. Do not let the blade contact
material it cannot cut, such as rocks, metal
etc.

27.Always wear safety boots, additionally a

helmet is required if there is a risk of contact
with falling objects.

For safe operation

Thank you for purchasing a KOMATSU ZENOAH product.
Before using our brushcutter, please read this manual carefully
to understand the proper use of your unit.

1-9 Minamidai, Kawagoe, Saitama, 350-1192 Japan