Zebra P1013372-001 REV. A - Manual

Introduction Components P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 3 Front View, Printer Cover Open The following figure shows components of the Printer. Transfer Film Transfer Station Print Ribbon Printhead(Under Print Ribbon) CardCleaningCartridge Card Cleaning Roller Rejec...

4 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Introduction Components Front View, Laminator Cover Open The following figure shows components of the Laminator. Heater Upper Laminate Cassette(single-sided and dual-sided laminators) Lower Laminate Cassette (dual-sided laminator o...

6 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Introduction Icons Icons Throughout this manual, different icons highlight important information, as follows: Zebra Supplies Genuine Zebra supplies meet stringent quality standards and are recommended for optimal printing quality a...

P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 7 2 Installation and Setup General Information This section will guide you through the installation and setup of your Card Printer. This consists of the following procedures, which should be performed in the order presented. • Unpack...

8 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Installation and Setup Unpacking the Printer Unpacking the Printer Step 1. Inspect the shipping container to ensure that no damage has occurred during shipment. If any damage is apparent, file a claim with the shipper. Step 2. Open...

10 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Installation and Setup Installing the Card Hoppers Installing the Card Hoppers Input Hopper The Input Hopper is positioned on the right side of the Printer and holds the cards to be printed. Step 1. Install the Input Hopper by sli...

Installation and Setup Loading Cards P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 11 Loading Cards Step 1. Remove the wrapping from the card deck. Step 2. Holding the card deck by the sides ( do not touch the print surfaces ), hold it vertically against a flat surface such as a...

12 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Installation and Setup Opening the Printer Door Opening the Printer Door Step 1. Press the Door Release button on the top of the Printer. Step 2. Observe that the Door releases and pops up approximately half an inch. Step 3. Grasp...

Installation and Setup Installing the Cleaning Cartridge P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 13 Installing the Cleaning Cartridge The Cleaning Cartridge cleans the cards entering the Printer from the Input Hopper. The Cleaning Cartridge consists of a Cartridge Frame an...

14 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Installation and Setup Installing the Cleaning Roller Installing the Cleaning Roller The Cleaning Roller cleans the cards entering the Printer from either the Input Hopper or the Single-Feed Input. Step 1. Remove the Cleaning Roll...

Installation and Setup Loading the Transfer Film P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 15 Loading the Transfer Film The ZXP Series 8 printer is designed to work only with Zebra True Colours™ i Series™ Transfer Film for near photographic print resolution and over-the-edge...

Installation and Setup Loading a Print Ribbon P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 17 Loading a Print Ribbon The ZXP Series 8 printer is designed to work only with Zebra True Colours ® i Series™ Ribbons in order to achieve rich, vibrant, image production over the full-c...

18 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Installation and Setup Loading a Print Ribbon Step 2. Load the print ribbon supply spool onto the supply spindles, purple flange side to the left . Step 3. Load the empty take-up spool onto the take-up spindle, blue flange side to...

Installation and Setup Loading the Laminate P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 19 Loading the Laminate Opening the Laminator Door Step 1. Grasp the Door at the bottom front. Step 2. Lift the Door to its upright position. It will remain in that position. Note that the ...

22 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Installation and Setup Loading the Laminate Loading the Laminate Cassette(s) Step 1. Remove the new roll of laminate from its packaging. Step 2. Cut the laminate as shown, as close to perpendicular as possible. Important • The gea...

Installation and Setup Loading the Laminate P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 27 Laminating Contact Smart Cards The laminate for the top surface of a contact smart card has a repeating pattern of an index hole and a rectangular cutout to expose the card’s electrical ...

Installation and Setup Loading the Laminate P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 29 Using Partial-Width Laminate Laminates come in three widths: “Full-Width” laminate is 2 in (51 mm) wide. The full-width laminate is used on the front (i.e., upper) or back (i.e., lower) ...

Installation and Setup Connecting Power P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 31 Connecting Power Step 1. Place the Printer’s power switch in the OFF ( ) position. Step 2. Depending on your local AC voltage, plug the appropriate power cord into the Printer’s power connec...

32 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Installation and Setup Connecting the Printer to your Computer Connecting the Printer to your Computer USB Connection Step 1. Connect the USB cable to the printer and the computer. Step 2. Ensure that the printer’s power switch in...

Installation and Setup Connecting the Printer to your Computer P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 33 Ethernet Connection Step 1. Connect the Ethernet Port on the rear of the printer to an Ethernet Network Port. Step 2. Turn the printer’s power switch to the ON ( ) pos...

34 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Installation and Setup Installing the Windows Printer Driver Installing the Windows Printer Driver Initial Steps Each computer that will use the printer must have the Printer Driver installed. If not already done, connect power to...

Installation and Setup Installing the Windows Printer Driver P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 35 Installing the USB Printer Driver Step 1. If not already done, connect power to the printer. Do not turn power ON. Step 2. Connect the USB port on the rear of the printe...

36 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Installation and Setup Installing the Windows Printer Driver Step 9. The InstallShield Wizard window will open. To proceed with the installation, click the Next button. Step 10. Select Install USB printer drivers , and click the N...

Installation and Setup Installing the Windows Printer Driver P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 37 Step 12. This will bring up the License Agreement window. To proceed with the installation, select the I accept the terms of the license agreement option , and then clic...

Installation and Setup Installing the Windows Printer Driver P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 39 Step 17. The Congratulations window will appear. Step 18. At this point, turn on your printer ; and then click the Next button. The Windows New Hardware Found wizard wil...

40 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Installation and Setup Installing the Windows Printer Driver Installing the Ethernet Printer Driver Step 1. If not already done, connect power to the printer. Turn power ON ( ). Step 2. Connect the Ethernet port on the rear of the...

Installation and Setup Installing the Windows Printer Driver P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 43 Step 14. Identify the printer: • Click on the Search button (arrow below) to search for all the Ethernet printers on the network, select the desired printer, and then cl...

P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 47 3 Operation Introduction Printing with the Card Printer is similar to printing with any other printer in a Windows environment. • The Printer Driver Software is installed on your computer (see Section 2 ). • The Printer is connect...

48 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Operation Card Type Selection Card Type Selection The Card Setup tab allows you to to specify the card type in use. Based on your selection, the printer automatically adjusts various printer properties for optimum print quality. T...

Operation Printing a Sample Card P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 49 Printing a Sample Card Sample card designs are installed with the printer driver. To print a sample card: 1. Access the Card Setup Tab, select Start > Printers and Faxes . Right click on the Zeb...

50 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Operation Manual Card Feed Manual Card Feed A Manual Feed Slot is available for feeding single cards. The Input Hopper must be empty for single-card feeding to work properly. 1. Access the Card Setup Tab: Select Start > Printer...

52 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Operation Operator Control Panel (OCP) Operator Control Panel ( OCP ) The printer is equipped with an OCP Display and three OCP Buttons which give access to the printer menus. The menus can be accessed when the printer status show...

Operation Operator Control Panel (OCP) P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 53 Operational Operational Messages are displayed during the Printer’s normal operation. MESSAGE DESCRIPTION ALARM An error message needs to be cleared before normal operations can resume. CANCE...

54 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Operation Operator Control Panel (OCP) Warning Messages Warnings alert the operator to action that should be taken; the printer will generally continue operation. Error Messages Errors are displayed when a situation causes the pri...

Operation Operator Control Panel (OCP) P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 55 Printer Menu Information Info Menu • Press the PREV button to move up the menu list • Press the NEXT button to move down the menu list • Press the EXIT button to return to the Operating Mode ...

56 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Operation Operator Control Panel (OCP) Main Menu Main Menu MENU Button (Operating Mode Display) RETURN PRINT TEST CARDS NETWORK SETTINGS ADVANCED SETTINGS See Print Test Cards Menu on page 57 See Network Settings Menu on page 58 S...

Operation Operator Control Panel (OCP) P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 59 Advanced Settings Menu Advanced Settings Menu UP DOWN SELECT Main Menu RETURN Displays current language, sets language option (English, French, Spanish, German, Brazilian Portuguese, or Itali...

P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 63 4 Printer Settings and Adjustments Introduction This section describes settings and adjustments that can be made to your Windows ZXP Series 8 Printer Driver. This consists of two major topics: Card Printer Properties . . . . . . ....

64 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Printer Settings and Adjustments Card Printer Properties Card Printer Properties To access the Card Printer Properties, select Start > Printers and Faxes . Right click on the Zebra ZXP Series 8 Card Printer listing, then select...

Printer Settings and Adjustments Card Printer Properties P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 65 General Tab The General tab shows the selected printer and lists the features of the printer. To access the General tab, select Start > Printers and Faxes . Right click o...

66 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Printer Settings and Adjustments Card Printer Properties Sharing Tab On the Sharing tab (Sharing Property Page), you can choose to share the printer over the network and install additional drivers to accommodate different operatin...

Printer Settings and Adjustments Card Printer Properties P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 67 Ports Tab Use the Ports tab to specify the computer port to which the printer is connected. This will have been established at the initial installation of the printer, and w...

68 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Printer Settings and Adjustments Card Printer Properties Advanced Tab The Advanced tab determines the spooling (queuing) of print jobs and determines how spooled jobs are handled relative to the most recent job. To access the Adva...

Printer Settings and Adjustments Card Printer Properties P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 69 Color Management Tab Color Management settings allow you to associate color profiles on the printer based on the type of media being used and printer configuration. The Add ...

70 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Printer Settings and Adjustments Card Printer Properties Security Tab This is the standard Windows security screen, showing user access to various printer control options. Both Print and Manage Printers must be checked for full fu...

Printer Settings and Adjustments Card Printer Properties P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 71 Device Information Tab The Device Information tab provides device information, security status, and printer usage. Access to Media Info and ZXP ToolBox is included. To acces...

74 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Printer Settings and Adjustments Card Printer Printing Preferences Advanced Black Panel Options Pop-Up The Advanced Black Panel Options pop-up window allows you to manage and configure Black Extraction. This window is available wh...

76 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Printer Settings and Adjustments Card Printer Printing Preferences Uv Panel Pop-Up A Uv Panel is a resin-based coating similar to a “K” panel and is used to print invisible images (text or graphics) that will glow in the visible s...

78 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Printer Settings and Adjustments Card Printer Printing Preferences Inhibit Pop-Up The Inhibit pop-up window allows you to select the inhibit panel area for mag stripe, signature panel, or other non-printing areas of a card. This w...

Printer Settings and Adjustments Card Printer Printing Preferences P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 79 Image Control Option The Image Control button brings up the Image Control window, which lets you make color adjustments to compensate for camera or lighting condit...

80 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Printer Settings and Adjustments Card Printer Printing Preferences Encoding Tab The Encoding screen allows the user to set various magnetic and smart card encoding options. To access the Encoding Tab, select Start > Printers an...

82 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Printer Settings and Adjustments Card Printer Printing Preferences About Tab The About Tab shows the copyright and the driver version for the Zebra ZXP Series 8 Card Printer . To access the About Tab, select Start > Printers an...

P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 83 5 ZXP Series Toolbox Introduction The ZXP Series Toolbox provides advanced configuration capabilities and tools to manage the operation of your printer. Note that the ZXP Series Toolbox is a separate application that works indepen...

84 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A ZXP Series Toolbox ZXP Series Toolbox Access ZXP Series Toolbox Access To access the ZXP Series Toolbox from the printer driver, select Start > Printers and Faxes . Then right-click on the Zebra ZXP Series 8 Card Printer listin...

ZXP Series Toolbox Information P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 85 Information Printer This information cannot be edited or changed by the user; however, this information may be useful for Zebra trained and certified personnel in diagnosing or evaluating printer sta...

86 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A ZXP Series Toolbox Information Sensors These characteristics cannot be edited or changed by the user; however, this information may be useful for Zebra trained and certified personnel in diagnosing or evaluating printer sensors st...

ZXP Series Toolbox Information P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 87 Media This screen displays ribbon, transfer film, and laminate details. This data is automatically read and updated from the installed media in the printer. • Ribbon Details include Type, Description...

88 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A ZXP Series Toolbox Information Laminator This information cannot be edited or changed by the user; however, this information may be useful for Zebra trained and certified personnel in diagnosing or evaluating laminator status. • S...

ZXP Series Toolbox Configuration P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 89 Configuration Image Control The Image Control window lets you make color adjustments to compensate for camera or lighting conditions. Keep in mind that these color adjustments modify how the pictur...

90 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A ZXP Series Toolbox Configuration Job Log The Job Log is a utility that builds a database of card transactions in the printer’s host computer. The Job Log records the data encoded on the card’s magnetic stripe, together with date, ...

ZXP Series Toolbox Configuration P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 93 Firmware and Settings The Firmware Download screen allows you to download firmware and firmware updates. Note that firmware updates can also be found at http://zebracard.com under Drivers & Dow...

ZXP Series Toolbox Configuration P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 95 • Temperature and Position Settings - Transfer Temperature Offset: Transfer Temperature Offset is provided to globally change the temperature of the heated rollers. If you have a single card type t...

96 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A ZXP Series Toolbox Cleaning Cleaning Clean Printer The Clean Printer screen gives you the option to clean the printer via the Toolbox; refer to Section 6 , for cleaning via the OCP. • Side Card Path When you click on the Clean but...

ZXP Series Toolbox Cleaning P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 97 • Front Card Path When you click on the Clean button, instructions will appear in the following sequence: 1. Insert the Y Roller Cleaning Card in the front feed slot. Click Ok after inserting the card. ...

98 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A ZXP Series Toolbox Cleaning Clean Laminator The Clean Laminator screen gives you the option to clean the laminator via the Toolbox; refer to Section 6 , for cleaning via the OCP. • Card transport Rollers When you click on the Clea...

ZXP Series Toolbox Print Test Card P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 99 Print Test Card Print Sample Card 1. View the Test Card Library . Use the scrollbar to view all the selections. 2. Set the front side: a. Select (click on) a card from the Test Card Library. b. C...

100 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A ZXP Series Toolbox Technology Technology Magnetic Encoding The Magnetic Encoding screen allows the user to test various magnetic encoding options. For more information on magnetic encoding, refer to Appendix D . Settings: EIN opt...

ZXP Series Toolbox Technology P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 101 Smart Card The Smart Card screen allows the user to test various smart card encoding options. For more information on smart card encoding, refer to Appendix E . • Card Readers: Select the card reader...

102 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A ZXP Series Toolbox Advanced Security Advanced Security Configure Security Enabling driver password protection prevents unauthorized persons from changing the printer configuration settings. Access to various printer screens can b...

ZXP Series Toolbox Advanced Security P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 103 To change the Password: 1. Enter your password in the Old password field. 2. Enter the new password in the New password and the Confirm password fields. 3. Click on the Apply button. Advanced ...

104 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A ZXP Series Toolbox Advanced Security Establish Security Roles Use this section used to establish security roles; i.e., grant and restrict access to various ZXP Series Toolbox screens. The list of users in the drop-down menu (e.g....

ZXP Series Toolbox Print Viewer P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 105 Print Viewer When you print a PRN file, you print directly to the printer, bypassing computer applications and associated printer drivers. This utility can be used to ensure that your printer is wo...

P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 107 6 C leaning Cleaning the Printer Clean your Printer using the Cleaning Cards provided. The regular use of these cards will clean and maintain important parts of your printer that cannot be reached, including the Printhead, Transp...

108 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Cleaning Cleaning the Printer Cleaning the Rollers Step 1. To initiate the cleaning process. a. Press the MENU button on the Operator Control Panel (OCP). The OCP will display the Main Menu. b. Scroll through the Main Menu, and s...

110 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Cleaning Cleaning the Printer Cleaning the Platen Step 1. Open the printer Door. Step 2. Remove the Transfer Film. Step 3. Manually run the Hot Roller Cleaning Card over the Platen. Step 4. Re-install the Transfer Film. Step 5. C...

Cleaning Cleaning the Laminator P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 111 Cleaning the Laminator Initiate the cleaning process: Step 1. Press the MENU button on the Operator Control Panel (OCP). The OCP will display the Main Menu. Step 2. Scroll through the Main Menu, an...

112 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Cleaning Cleaning the Laminator Cleaning: Laminator Media Feed Rollers The default cleaning interval is once every 5000 cards. Step 1. Select Clean Lam Rollers to run the Laminator Roller Cleaning Routine. Step 2. Lift the Lamina...

116 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Cleaning Cleaning the Printhead Cleaning the Printhead Printhead cleaning removes deposits when print anomalies persist. To avoid deposits, only use foam-tipped swabs or pens. Step 1. Place the printer power switch in the OFF ( )...

Cleaning Card Cleaning Cartridge P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 117 Card Cleaning Cartridge The Card Cleaning Cartridge cleans the cards entering the printer through the card feeder. To ensure print quality, the card cleaning roller requires periodic replacement. ...

P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 119 The table on the next page offers causes and solutions to symptoms related to improper operation. Check the table when experiencing any loss of operation or print quality. Use the following figure in conjunction with the table to...

120 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Troubleshooting OCP Error Messages OCP Error Messages ERROR MESSAGE POSSIBLE CAUSE POSSIBLE SOLUTION BOTTOM LAMINATE FEED • Bottom laminate cartridge is not installed properly. • Cartridge is not removed when that side of the car...

128 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Troubleshooting Test Card Descriptions Test Card Descriptions Image Description Print artifacts to look for with this image Mid Gray Flat uniform gray Motion artifacts, banding, platen defects, transfer artifacts, dirt, overall d...

Troubleshooting Ethernet Issues P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 129 Ethernet Issues If both LEDs are off, the printer has not detected the presence of a network cable. To solve the problem: • Verify that the network cable is appropriate and has an RJ-45 connector. ...

P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 131 8 Technical Specifications Standard Features • Thermal transfer and dye diffusion to transfer film • Full color or monochrome reverse transfer printing • Single- and dual-sided printing • Maximum print speed (batch mode; i.e., th...

132 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Technical Specifications Specifications Specifications Encoding Options • Smart card contact encoder – ISO 7816, PC/SC Compliant • Magnetic stripe encoder – ISO 7811 and JIS-II (new and re-encoded; tracks 1, 2, and 3; high and lo...

Technical Specifications Specifications P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 133 Card Compatibility • Card Thickness: 30 – 40 mil • Card Size: ISO 7810 format, Type ID-1, CR-80 • Card Material: ABS; PVC, Composite; TESLIN, Composite; PET; PETG; Polycarbonate; PVC Agency...

134 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Technical Specifications Specifications Electrical • Auto-switching Single-phase AC power • 90V~264V AC RMS and 47-63 HZ (50-60 Hz nominal) • Power consumption: Idle 160 W Printing 340 W Initializing / Warm-up 570 W Sleep 20 W Ph...

Technical Specifications Declarations of Conformity P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 135 Declarations of Conformity For a formal certificate, please contact the Compliance Office at Zebra’s Camarillo facility. EUROPE: Norway Only: This product is also designed for I...

P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 137 A PPENDIX A Printer Configurations Introduction The Part Number of a particular printer is shown on a label affixed to the bottom of the printer; that Part Number identifies the specific configuration for that printer. The chart ...

138 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Printer Configurations Part Numbers PART NUMBER DESCRIPTION Z 8 _ Base Unit _ _ 3 _ _ 4 - - _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Dual-sided printing with single-sided lamination Dual-sided printing with dual-sided lami...

P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 139 Appendix B Setting Custom Card Specifications B.1 Introduction This document is to be used for setting the specifications for cards not listed in the Card type in use dropdown menu; circled below. Setting the specifications for a...

140 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Setting Custom Card Specifications Process Flowchart B.2 Process Flowchart partial transfer? flash? examine card print card start stop no no no no yes yes yes yes adjust transfer temperature adjust transfer speed adjust transfer ...

Setting Custom Card Specifications 3-Step Process P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 141 B.3 3-Step Process Step 1: Select the Card Type From the Card type in use dropdown menu, select Custom 1 or Custom 2 ; and click OK. Note that Custom 1 or Custom 2 have adjustable...

142 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Setting Custom Card Specifications 3-Step Process Step 2: Make adjustments After selecting Custom 1 or Custom 2 , the Card Specifications window will appear. Make the recommended transfer temperature and/or transfer speed adjustm...

Setting Custom Card Specifications 3-Step Process P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 143 Step 3: Print and examine Test Card From the Card Setup tab, print (click on the Test Print button circled below) and examine a test card. The quality of the test card will determ...

146 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Setting Custom Card Specifications Adjustments B.4.2 Partial Transfer Front of card Partial transfer is usually caused by lack of energy being transferred to the card, i.e. the temperatures are too low or the speeds are too fast....

Setting Custom Card Specifications Adjustments P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 149 Back of card Partial transfer is usually caused by lack of energy being transferred to the card, i.e. the temperatures are too low or the speeds are too fast. Step 1. Increase Back T...

152 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Setting Custom Card Specifications Adjustments B.4.3 Warpage Edges curled down Warpage is usually caused by too much energy being transferred to the card; i.e., the temperatures are too hot or the speeds are too slow. Step 1. Dec...

Setting Custom Card Specifications Adjustments P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 155 Edges curled up Warpage is usually caused by too much energy being transferred to the card, i.e. the temperatures are too hot or the speeds are too slow. Step 1. Decrease Front Trans...

158 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Setting Custom Card Specifications Adjustments Irregular Warpage Warpage is usually caused by too much energy being transferred to the card, i.e. the temperatures are too hot or the speeds are too slow. Step 1. Decrease Front Tra...

166 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Setting Custom Card Specifications Adjustments B.4.5 Flash Flash is usually caused by too much energy being transferred to the card (i.e., temperatures are too high or input speed is too slow) and not allowing enough time for the...

Setting Custom Card Specifications Adjustments P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 169 Leading Edge Step 1. Decrease Front Transfer Temperature : a. Go to the Card Specifications window; see Section B.3 . b. Make a note of the default front transfer temperature setting...

Setting Custom Card Specifications Adjustments P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 171 B.4.6 Special Cases Flash on Smart Card Chip Step 1. Decrease Front Transfer Temperature: a. Go to the Card Specifications window; see Section B.3 . b. Make a note of the default fro...

Setting Custom Card Specifications Adjustments P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 175 Flash on Magnetic Stripe Step 1. Decrease Back Transfer Temperature: a. Go to the Card Specifications window; see Section B.3 . b. Make a note of the default back transfer temperatur...

Setting Custom Card Specifications Adjustments P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 179 Excess Leading-Edge Flash on Mag Cards Use image with black printed line or text above the mag stripe (arrows below). To assist with this issue, you can use the Inhibit pop-up window...

P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 181 Appendix C Network Operations This section covers: Adding a Network Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182 Pooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

182 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Network Operations Adding a Network Printer Use this procedure if you have already installed an ethernet printer on your system (refer to Section 2 ), and you want to install a second ethernet printer on the network via the Micro...

184 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Network Operations Step 12. Observe a second Add Standard TCP/IP Port Wizard window. Step 13. Enter the IP Address of your printer. Note that the Port Name will automatically be filled in when you enter the IP Address. Do not cha...

Network Operations P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 189 Pooling Setting Up Printer Pooling Printer Pooling is a standard feature of Windows, which lets you spread your printed output across a pool of several printers. In this example, we will install and setup the t...

190 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Network Operations Using the Printer Pool When the first printer has taken as many jobs as it can handle (that being two jobs - one to be printed immediately, the other waiting), the following jobs “spill over” to the second prin...

P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 191 Appendix D Magnetic Card Encoder Introduction This Appendix includes operation and maintenance requirements for Printers with the optional magnetic card stripe encoder. The magnetic encoder can be set for either high or low coerc...

192 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Magnetic Card Encoder Driver Setting The Card Setup tab allows the user to specify the Magnetic Encoder Card Type in use. Based on your selection, the printer automatically adjusts various printer properties for optimum performan...

Magnetic Card Encoder P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 193 Media Loading Orientation Place the cards in the Input Hopper in the correct orientation as shown (with the magnetic stripe down and facing to the rear). Ensure that the cards are seated properly the hopper....

194 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Magnetic Card Encoder Magnetic Encoder Cleaning The Magnetic Encoder is cleaned as part of the printer cleaning process; see Section 6 . If the frequency of encoding errors increases, the head may need additional cleaning. To cle...

196 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Magnetic Card Encoder AAMVA Alpha-numeric characters on Tracks 1 and 3, numerals only on Track 2. CUSTOM If a custom format is desired, the ISO standard format may be used as a starting point. The standard format can then be modi...

Magnetic Card Encoder P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 197 Encoder Macro Commands With ZXP Series 8 printers, we provide support for pass-through mag encoding commands. The application developer or user can use a preamble or Macro to indicate to the driver that the ...

P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 199 A PPENDIX E Smart Card Options Introduction This Appendix contains information on the additional operations of a Printer equipped with one or more of the available Smart Card options. Smart Cards can have a built-in microcomputer...

200 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Smart Card Options Encoding and Reading Smart Cards Encoding data onto Smart Cards and reading the data previously encoded on them is totally under control of the application software; no operator action is required. If you exper...

Smart Card Options P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 201 Contact Smart Cards Contact Smart Cards have a pad of contacts on the surface of the card that connect to the circuitry embedded into the card. The printer responds to commands that position the card at the con...

202 Zebra ZXP Series 8 Card Printer with Laminator P1013372-001 Rev. A Smart Card Options Contact Station Smart Card Interface When a command to the printer interface sends a card to the Smart Card Contact Station, the printer connects the Smart Card Contact Station to the female DB-9 connector on t...

Smart Card Options P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 203 Contactless Smart Cards Rather than using a contact pad, Contactless Smart Cards use various short-range radio technologies to “connect” to the printer. The printer moves the card to an antenna location on the ...

P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 205 Appendix F Packing the Printer for Shipment Introduction If the printer is to be shipped, it is important to use the original packing and shipping material to prevent damage to the Printer. If the original material is lost, a rep...

P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 209 A PPENDIX G Worldwide Support For Technical Support or Repair Services, contact the appropriate facility listed below. North America and Latin America - Technical Support Phone: +1 877 ASK ZEBRA (877 275 9327)+1 847 913 2259 emai...

Worldwide Support P1013372-001 Rev. A Zebra ZXP Series 8 Card Printer with Laminator 211 Asia Pacific - Technical Support Zebra Technologies Asia Pacific Pte. Ltd.120 Robinson Road#06-01 Parakou BuildingSingapore 068913 Phone: +65 6858 0722 Fax: +65 6885 0838 Email: [email protected] Asia Paci...