Zebra 980293-001 - Manual

980293-001 Rev. A v TABLE OF CONTENTS Installation and Operation . . . . . . . . . . . . . . . . . 1 Unpacking Your Printer . . . . . . . . . . . . . . . . . . . . 2Getting To Know Your Printer . . . . . . . . . . . . . . . . . 3Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Aut...

Unpacking Your Printer 2 980293-001 Rev. A Installation and Operation User Do cum entati on & S oftw are

Step ➋ Attach Interface Cable The printer has either a parallel interface or aserial interface (with optional RJ-11 connector). For additional information on serial cable wir-ing, refer to Appendix A. 980293-001 Rev. A 5 Installation and Operation Parallel Interface Power OFF RJ-11 Interface (Option...

Step ➌ Load Labels 6 980293-001 Rev. A Installation and Operation MOVIE Open Cover Power ON Adjust Holders 1.0 inch 2.5 cm 1.5 inch 3.8 cm MOVIE

Load Labels - continued If the indicator remains dark, see Appendix A -Troubleshooting. 980293-001 Rev. A 7 Installation and Operation Install Roll Thread Through Guides Close Cover Tap Feed Button

Step ™ AutoSense Gap Sensor Adjustment Perform this procedure when loading a newroll. If your printer has the label dispenser option, turn OFF the label taken sensor. 8 980293-001 Rev. A Installation and Operation MOVIE Power OFF Hold Feed Button Power ON

AutoSense Gap Sensor Adjustment - continued If the indicator remains orange or red, see thetroubleshooting steps. 980293-001 Rev. A 9 Installation and Operation When Indicator Flashes, Release Feed Button 4 MO3351F 16 V3.21 Serial port : 96,N,8,1 Image buffer size:245K Fmem:000,0K,019.9K avl Gmem:00...

Label Dispenser Option 10 980293-001 Rev. A Installation and Operation Open Door Use a Stylus to Switch On the Label Taken Sensor Remove Several Labels Push Liner Through Slot Close Door MOVIE

Appendix A - Troubleshooting Problem Solution or Reason STATUS Indicator Does not light when powerswitch is turned to ON (I)position. 1. Check power connections from A.C. outlet to power supply to printer. Lights GREEN, but printerwill not print. 1. Check interface cable connections from computer to...

Other Support Resources The first troubleshooting reference source is thetable on the previous page. Next, contact thedealer where you purchased your printer. Zebra Technologies also provides a variety ofinformation and user support services: • Internet : http://www.eltron.comftp: //ftp.eltron.com e...

Serial Interface Cable Wiring The figure below displays the cable wiringrequired to use the printer's RS-232 serialinterface. 16 980293-001 Rev. A Appendix A - Troubleshooting N/C RxD TxD DTR GND DSR RTS RI CTS Printer Host 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 DB-9 Pin # DB-9 Pin # Female DB-9 to Mal...

Cash Drawer Cable Wiring The figure below displays the pin assignmentsfor the printer's retail cash drawer interface. Re-fer to the cash draw manufacturer's documenta-tion for proper drawer wiring. *+24 volts D.C. at no greater than 1.5 amps. 980293-001 Rev. A 17 Appendix A - Troubleshooting PRINTER...

Parallel Interface Cable Wiring The figure below displays the cable wiringrequired to use the printer's Centronics parallelinterface. +5 volts at 300 mA for external device (e.g. KDU or scanner) Appendix A - Troubleshooting 18 980293-001 Rev. A PRINTER DB-25 Pin No. Centronics Pin No. Female DB-25 t...

Appendix B - Accessories Accessories available for the printer are listedbelow. Always refer to the ELTRON part num-ber when placing an order. For the name of anEltron brand dealer in your area, call: 1(805) 579-1800 or the nearest Zebra Technologies office (located on the back of this manual). Desc...