Zebra 3742 - Manual - manualsarea.com

Page 2 - Industry Canada Notice:; ii

COPYRIGHT NOTICE This document contains information proprietary to Zebra Technologies Corporation. This docu- ment and the information contained within is copyrighted by Zebra Technologies Corporation and may not be duplicated in full or in part by any person without written approval from Zebra Tech...

Page 3 - TABLE OF CONTENTS; Installation and Operation; iii

TABLE OF CONTENTS Installation and Operation Unpacking Your Printer . . . . . . . . . . . . . . . . . . . . 2 Getting To Know Your Printer . . . . . . . . . . . . . . . . . 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Attach Power . . . . . . . . . . . . . . . . . . . . . ....

Page 4 - iv

General Cautions and Warnings This page describes general safety and maintenance warnings and cautions for the printer and are referenced throughout the manual. Warning - Shock Hazard The printer should never be operated in a location where it can get wet. Personal injury could result. Warning - Sta...

Page 6 - Unpacking Your Printer

Page 7 - Getting To Know Your Printer

Getting To Know Your Printer 980344-001 Rev.A 3 Installation and Operation

Page 8 - Installation; The following steps will guide you through the; Step; SHOCK HAZARD WARNING; Power OFF

Installation The following steps will guide you through the installation of the printer, media and software. Step 1 - Attach Power SHOCK HAZARD WARNING See page iv Installation and Operation 4 980344-001 Rev.A O XXXXXXXXXXXXXX XXXXXXXX XXXXXXXXX Power OFF Check Power Module Voltage Plug Into Power M...

Page 9 - Parallel Interface

Step 2 - Attach Interface Cable 980344-001 Rev.A 5 Installation and Operation Parallel Interface Serial Interface

Page 10 - Open Cover

Step 3 - Load Media Installation and Operation 6 980344-001 Rev.A Open Cover Open Print Head Open Guides MOVIE MOVIE MOVIE

Page 12 - Install Roll

Step 3 - Load Media (cont.) Installation and Operation 8 980344-001 Rev.A 2722 Install Roll Media OUT OUT OUT OUT OUT OUT OUT OUT 2742 / 3742 Install Roll MOVIE

Page 13 - Thread the Media; Seat Media Roll

Step 3 - Load Media (cont.) 980344-001 Rev.A 9 Installation and Operation Thread the Media MOVIE MOVIE Seat Media Roll

Page 14 - Close Guides

Step 3 - Load Media (cont.) Installation and Operation 10 980344-001 Rev.A Close Guides Close Guides 2742 / 3742 MOVIE

Page 15 - Close Cover; Close Print Head

Step 3 - Load Media (cont.) 980344-001 Rev.A 11 Installation and Operation Close Cover MOVIE MOVIE Close Print Head

Page 16 - If the indicator fails to light, refer to; Press FEED Button

Step 3 - Load Media (cont.) If the indicator fails to light, refer to Appendix A - Trouble Shooting. Run the AutoSense routine. Installation and Operation 12 980344-001 Rev.A Press FEED Button O Power ON

Page 17 - Start your computer and follow the installation; Computer ON

Step 4 - AutoSense Step 5 - Install Software Start your computer and follow the installation instructions on the compact disc (CD). 980344-001 Rev.A 13 Installation and Operation O O 2 UKQ1813 4.00 Serial port : 96,N,8,1 Image buffer size:245K Fmem:000,0K,019.9K avl Gmem:000K,0241K avl E I8,0,001 rY...

Page 18 - Place Media In Rear

Using Fan-Fold Media Installation and Operation 14 980344-001 Rev.A Place Media In Rear Face Print Surface UP Insert & Load Media

Page 19 - Label Dispenser; Printers with an optional label taken sensor can

Label Dispenser Printers with an optional label taken sensor can dispense a single peeled label. Remove the label to automatically print the next label. 980344-001 Rev.A 15 Installation and Operation Expose 15CM of Labels (2722 Shown) Peel Exposed Labels Cut End of Exposed Liner (2722 Shown) Pull Pr...

Page 20 - Label Dispense Option; Insert Liner

Label Dispense Option Installation and Operation 16 980344-001 Rev.A TLP 2722 Insert Liner (2742 Shown) Pull Liner Through (2742 Shown)

Page 22 - Thermal Transfer Ribbon Loading; This feature is supported on TLP model; Thermal Transfer; Ribbon Path

Thermal Transfer Ribbon Loading This feature is supported on TLP model printers, only. Installation and Operation 18 980344-001 Rev.A Thermal Transfer Print Head Mechanism MOVIE Ribbon Path

Page 25 - Appendix A - Troubleshooting; Problem

Appendix A - Troubleshooting Problem Solution or Reason POWER indicator does not light GREEN when power switch is turned to ON (1) position. 1. Check power connections from A.C. outlet to power supply to printer. POWER indicator lights GREEN, but printer will not print. 1. Check interface cable conn...

Page 26 - Clean the

Printer Maintenance 22 980344-001 Rev.A Clean the Print Head Don’t Clean Rollers with Cleaning Pen MOVIE

Page 27 - OD; Dump Mode; command in

Printer Configuration Settings The printer has flash (non-volatile) memory to store printer configuration settings. The settings are stored in flash memory and are set by programing, printer drivers or the AutoSense routine. The settings are shown on the Dump mode printout or can be reported back to...

Page 28 - Printer

Serial Interface Communication Configuration The printer’s serial port is configured with the Y command for the printer. The printer supports interface data rates from 1200 to 38,400 baud. See the programmer's manual for details. The printer’s serial port default configuration is: 9600 baud 8 bit da...

Page 29 - The figure below displays the cable wiring; PRINTER; Female DB-25 to Male Centronics; HOST

Parallel Interface Cable Wiring The figure below displays the cable wiring required to use the printer's Centronics parallel interface. +5 volts at 300 mA for external device (e.g. PrintServer) 980344-001 Rev.A 25 PRINTER DB-25 Pin No. Centronics Pin No. Female DB-25 to Male Centronics (Cable) HOST ...

Zebra 3742 - Manual

Table of Contents:

Summary

Other Zebra Models