Page 2 - Important Safety Information
3 Important Safety Information You MUST read hese warnings carefully before installing or using the hob.If you need assistance, contact our Customer Care Departmenton 01635 521313 Installation ● This hob must be installed by qualified personnel,according to the manufacturer’s instructions and tothe ...
Page 3 - Guide to Use the instructions; For the User; Contents; For the Installer
4 This appliance complies with the followingE.E.C. Directives:* 73/23 - 90/683 (Low VoltageDirective); * 93/68 (General Directives);* 89/336 (ElectromagneticalCompatibility Directive);* 90/396 (Gas Appliances),and subsequent modifications Guide to Use the instructions The following symbols will be f...
Page 4 - Description of the Hob
5 1. Hob Top 2. Auxiliary Burner 3. Semi-rapid Burners 4. Ultra-rapid Double-crown Burner 5. Rapid Burner 6. Ignition pushbutton 7. Control knob for front left burner (auxiliary) 8. Control knob for back left buner (semi-rapid) 9. Control knob for central burner (ultra-rapid) 10. Control knob for ba...
Page 5 - Operation; Using the Wok Stand
6 Operation HOB BURNERS To light a burner, push the relevant control knob in,turn it anticlockwise to maximum position, anddepress the ignition pushbutton marked by a smallelectric spark symbol. Then adjust the flame asrequired.If the burner does not ignite, turn the control knob tozero, and try aga...
Page 6 - Maintenance and Cleaning
7 Before any maintenance or cleaning can becarried out, you must DISCONNECT thehob from the electricity supply. The hob is best cleaned whilst it is still warm, asspillage can be removed more easily than if it is leftto cool. The Hob Top Regularly wipe over the hob top using a soft clothwell wrung o...
Page 7 - Something Not Working?; Service and Spare Parts
8 Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local ZanussiService Force Centre. SYMPTOM ■ There is no spark when lighting the gas ■ The gas ring burns unevenly SOLUTION ◆ Check that the unit is plugged in and the electrica...
Page 8 - Peace of Mind for 24 Months
9 ZANUSSI GUARANTEE CONDITIONS We, Zanussi, undertake that if, within 24 months ofthe date of the purchase, this Zanussi appliance orany part thereof is proved to be defective by anyreason only of faulty workmanship or materials, wewill, at our option, repair or replace the same FREEOF ANY CHARGE fo...
Page 9 - Instructions for the Installer; Engineer technical data
10 OVERALL DIMENSIONS Width: 680 mm. Depth: 510 mm. Height: 72 mm. Weight: 12 Kg. CUT OUT DIMENSIONS Width: 560 mm. Depth: 480 mm. Thickness: 30 mm. Ignition HT Spark Spark Generator Ispra Control's BF 50066 - 240V 0.6 YA T 120 Spark Gap Fixed Rear Left Burner (semi rapid)Heat Input 2.0 kW (6824 BTU...
Page 10 - Important safety requirements; Location
11 INSTALLATION GUIDANCE INSTRUCTIONS CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE INSTALLATION GUIDANCE INSTRUCTIONS CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITH A COOKER HOOD ABOVE 700 mm 400 mm 100 mm 400 mm 50 mm 50 mm 55 mm 650 mm 400 mm 400 mm 100 mm 50 mm 50 m...
Page 11 - Gas Connection; Installation; Cut Out Size
12 Rectangular cut-out size for hob A) End of shaft with nutB) WasherC) Elbow It is important to install the elbow correctly,with the shoulder on the end of the thread,fitted to the hob connecting pipe.Failure to ensure the correct assembly willcause leakage of gas. FO 0814 Gas Connection Connection...
Page 12 - Fitting the Hob into the worktop; Building In; Building over a cupboard or drawer
13 ON/OFF SWITCH FLEXOUTLET ON/OFF SWITCH FLEXOUTLET FO 0763 FO 0764 30 20 min 60 a b FO 1013 1 2 3 50 50 FO 2039 FO 0199 a Fitting the Hob into the worktop Carry out the building in of the hob as follows: • put the seals supplied with the hob, on theedges of the cut out: place them exactly onthe fr...
Page 13 - Electrical connections
14 Electrical connections Any electrical work required to install thishob should be carried out by a qualifiedelectrician or competent person, inaccordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liabilityshould these safety measures not beobserved. This...
Page 14 - Wiring Diagram
15 A. IGNITOR SWITCH B. IGNITOR UNIT B L N 0 1 2 3 4 5 6 220/240 A Wiring Diagram
Page 15 - Fault Finding; Preliminary Electrical Systems Check
16 Fault Finding Preliminary Electrical Systems Check A. EARTH CONTINUITY CHECK -Appliance must be electricallydisconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary. a) Test leads from any appliance earth point to earth pin on plug. Resistance shouldbe less than 0.1 Ω (Ohm), ch...
Page 16 - Ignition System / Gas Ignition
17 Ignition System / Gas Ignition YES Check plug top fuse andreplace if necessary Check polarity and earthcontinuity of supply point Check earth continuityof appliance Ignitor does not spark Check fitting of burners Check position of theelectrode Check by pass simmeradjusted Light burner manually Ch...
Page 17 - Commissioning
18 Commissioning When the hob has been fully installed it will benecessary to check the minimum flame setting. To dothis, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turnthe control knob from MIN to MAX several times...
Page 18 - Servicing
19 A: Removal Of Hob Top 1. Remove all control knobs, pan supports, burner caps and burner crowns. 2. Remove 2 screws for each burner.3. Remove 6 fixing screws from the pan support hinges, and remove the hinges from the hob. 4. Lift hob top at the rear and disengage it from the front locators. B: Re...
