Zanussi ZDT 6454 - Manual - manualsarea.com

Page 2 - Contents

Thank you for selecting ourappliance We wish you lots of enjoyment with your newappliance and we hope that you will considerour brand again when purchasing householdappliances.Please read this user manual carefully andkeep it throughout the product life cycle as areference document. The user manual ...

Page 3 - Safety information; Correct use

Safety information In the interest of your safety and to ensure thecorrect use, before installing and first using theappliance, read this user manual carefully, in-cluding its hints and warnings. To avoid unnec-essary mistakes and accidents, it is importantto ensure that all people using the applian...

Page 4 - Installation; Control panel; Functions buttons

Installation • Check your dishwasher for any transport damage. Never connect a damaged ma-chine. If your dishwasher is damaged con-tact your supplier. • All packaging must be removed before use.• Any electrical and plumbing work required to install this appliance must be carried out bya qualified an...

Page 5 - MUST

• the setting of the water softener,• deactivation/activation of the audible sig- nals. IMPORTANT! Setting mode Always remember that when:– setting the water softener,– deactivation/activation of the audible sig- nals, the appliance MUST be in setting mode: • Press On/Off button, All programme light...

Page 6 - Audible signals; end of programme; Select and start a washing programme

Audible signals Audible signals have been introduced to helpindicate which operations the dishwasher isperforming:• setting the water softener,• end of the programme,• intervention of an alarm due to malfunction. IMPORTANT! Factory setting: audible signals activated. Deactivation/activation of the a...

Page 8 - Washing programmes

IMPORTANT! When the washing programme has finished, itis recommended that the dishwasher is un- plugged and the water tap turned off. Washing programmes Programme Degree of soil Type of load Programme descrip- tion Intensive 70° Heavy soil Crockery, cutlery, potsand pans PrewashMain wash2 intermedia...

Page 10 - Setting the water softener manually (see table); The dishwasher is factory set at level 5.

The softener should be adjusted according tothe hardness of the water in your area. Your local Water Authority can advise you on thehardness of the water in your area. Water hardness Adjusting the water hardness setting Use of salt °dH °TH mmol/l manually electronically 51 - 70 91 - 125 9,1 - 12,5 2...

Page 11 - Filling with dishwasher salt

1. Press the On/Off button. The dishwasher must be in setting mode. 2. Simultaneously press and hold function buttons B and C until the lights of the func- tion buttons A , B and C start flashing. 3. Press function button A , the lights function buttons B and C turn off while the light of function b...

Page 14 - Loading cutlery and dishes

Loading cutlery and dishes Sponges, household cloths and any object thatcan absorb water may not be washed in thedishwasher.• Before loading the dishes, you should: – Remove all left over food and debris.– Soften remnants of burnt food in pans • When loading the dishes and cutlery, please note:– Dis...

Page 16 - Use of detergent

Move the front runnerstops (A) of the upper bas-ket outwards and slide thebasket out. Refit the basket in thehigher position and re-place the stops (A) in theiroriginal position. IMPORTANT! When the basket is in the higher position you will notbe able to use the cup racks. Use of detergent IMPORTANT...

Page 17 - Unloading the dishwasher; Care and cleaning; Cleaning the filters

For programmes withprewash add an addition-al detergent dose in com-partment B . When using detergenttablets: place detergenttablets in compartment A . Close the lid. Unloading the dishwasher • Hot dishes are sensitive to knocks. The dishes should therefore be allowed tocool down before removing fro...

Page 18 - Cleaning the spray arms; External cleaning

Clean filters A , B and C thoroughly under runningwater. Turn the handle about 1/4turn anticlockwise andremove filters B and C . Remove filter A from the base of the washingcompartment. Put the flat filter A back in the base of the washingcompartment and ensurethat it fits perfectly underthe two gui...

Page 19 - Environmental concerns; Packaging material

2. Leave the door ajar to prevent the forma- tion of any unpleasant smells. 3. Leave the inside of the machine clean. Frost precautions Avoid placing the machine in a location wherethe temperature is below 0°C. If this is unavoid-able, empty the machine, close the appliancedoor, disconnect the water...

Page 20 - Something not working

Something not working The dishwasher will not start or stops duringoperation.Certain problems are due to the lack of simplemaintenance or oversights, which can be solved with the help of the indications describedin the chart, without calling out an engineer.Switch off the dishwasher and carry out th...

Page 22 - Technical data; Hints for test institutes

Consumption values The consumption values are intended as aguide and depends on the pressure and thetemperature of the water and also by the var- iations of the power supply and the amount ofdishes. Consumption values Programme Programme duration (in minutes) Energy consumption (in kWh) Water (litre...

Page 23 - Water connection

rinse aid respectively and using the test pro-gramme (see "Consumption values"). Full load: 12 standard place settings Amount of detergent required 5 g + 25 g (Type B) Rinse aid setting position 4 (Type III) Upper basket Cutlery basket Lower basket cup racks: position A Installation WARNING!...

Page 26 - Guarantee conditions; European Guarantee

Fitting under a counter IMPORTANT! Carefully follow the instructions on the enclosedtemplate for building in the dishwasher and fit-ting the furniture panel. WARNING! The dishwasher must be secured against tilting.Therefore make sure that the counter it is fixedunder, is suitably secured to a fixed ...